TJM Posted February 21 Author Share #91 Posted February 21 (edited) Log entry 22 A bit of progress. I have completed the lower shrouds and spent a couple of evenings with the futtock staves and shrouds. Up close, it is not the neatest work - I find it quite difficult to deal with the thin thread! From a little distance, it looks alright to me. The manual says to wait with the backstays until the yards are fitted, but I had a slight tilt to one side from the topgallant and up on the main mast, so I wanted to temporarily attach the backstays to correct this while I work on the topgallant shrouds. If I can work around them, I will leave them in place and otherwise it is not very much work to detach them and re-do the two lanyards. BR TJM Edited February 21 by TJM Thukydides, The Gimps Chimp, rcweir and 6 others 9 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
TJM Posted March 10 Author Share #92 Posted March 10 (edited) Log entry 23 I am still here! I have just had very few days where I have been able to get any work done in the workshop. I have completed the ratlines on lower main mast shrouds and sre working on the upper mizzen shrouds. My plan is to complete all shrouds and ratlines and then do the yards before continuing with the stays. BR TJM Edited March 10 by TJM The Gimps Chimp, wvdhee, Glenn-UK and 7 others 10 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
wvdhee Posted March 10 Share #93 Posted March 10 Looking really good 😃 TJM 1 Quote Walter. Current build: Thinking about it Finished build: HMS Flirt Link to comment Share on other sites More sharing options...
TJM Posted March 10 Author Share #94 Posted March 10 4 hours ago, wvdhee said: Looking really good 😃 Thanks! 😊 Mr Whippy 1 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
TJM Posted March 19 Author Share #95 Posted March 19 (edited) Log entry 23 I have now completed all the mast shrouds - milestone reached! I estimate that I need another 4-5 evening sessions to do the remaining ratlines. But after that I get to continue with the yards! The topgallant shrouds visually adds some much needed bulk to the top of the model, so I was very pleased with the improved look after yesterdays work! BR TJM Edited March 19 by TJM Spelling ccoyle, Theodosius, DB789 and 5 others 8 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
allanyed Posted March 20 Share #96 Posted March 20 (edited) Overall VERY neatly done! You may want to redo the blocks under the tops as they appear to be upside down so the line would rub against the tail rather than over the would be sheave. It may be easier to just drill the upper holes rather than unrig and re-rig. Allan Edited March 20 by allanyed TJM, Thukydides and Ryland Craze 3 Quote PLEASE take 30 SECONDS and sign up for the epic Nelson/Trafalgar project if you would like to see it made into a TV series. Click on http://trafalgar.tv There is no cost other than the 30 seconds of your time. THANK YOU Link to comment Share on other sites More sharing options...
TJM Posted March 20 Author Share #97 Posted March 20 Hi Allan, Thank you for your comment! Do I understand correctly that the one hole in the blocks should be closest to where the block is attached? So that when the line runs down, it would appear to go over the (imaginary) sheave inside the block? allanyed and Thukydides 2 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
Thukydides Posted March 20 Share #98 Posted March 20 14 minutes ago, TJM said: Hi Allan, Thank you for your comment! Do I understand correctly that the one hole in the blocks should be closest to where the block is attached? So that when the line runs down, it would appear to go over the (imaginary) sheave inside the block? Yes, that is correct. As Alan said you could probably just drill a new hole as that might be easier than removing the block and reattaching it. TJM, Ryland Craze and allanyed 3 Quote Current build: HM Cutter Alert (Vanguard Models) Link to comment Share on other sites More sharing options...
TJM Posted March 20 Author Share #99 Posted March 20 (edited) Great, thanks! Both to @allanyed and @Thukydides! Edited March 20 by TJM Mr Whippy, Thukydides and allanyed 3 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
allanyed Posted March 20 Share #100 Posted March 20 TJ You can see from the drawing that there is no room for the line between the sheave and tail piece, only between the sheave and the crown. For our purposes, holes on both ends are fine at most scales as the line will block view of the lower hole. Allan TJM and Mr Whippy 2 Quote PLEASE take 30 SECONDS and sign up for the epic Nelson/Trafalgar project if you would like to see it made into a TV series. Click on http://trafalgar.tv There is no cost other than the 30 seconds of your time. THANK YOU Link to comment Share on other sites More sharing options...
TJM Posted March 24 Author Share #101 Posted March 24 Log entry 24 All of the lower ratlines have been completed! Not much else to say - on with the top ones! BR TJM KARAVOKIRIS, dunnock, wvdhee and 3 others 6 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
TJM Posted April 6 Author Share #102 Posted April 6 (edited) Log entry 25 All the ratlines are now done! Progress has been slow, as I have not had many sessions in the workshop lately - I was away during Easter. I am a bit relieved that this part of the build is done. On one hand, I find that I don't mind doing the ratlines while I do them, but it does take a very long time and it feels like not much overall progress i made while working on them I had thought to continue with the yards, but as you may have spotted, I have ordered and received the 18 foot cutter from Vanguard Models. So now I will take a quick detour with that for a while! The first few planks are on already. BR TJM Edited April 7 by TJM Spelling KARAVOKIRIS, DB789, The Gimps Chimp and 4 others 7 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
TJM Posted April 8 Author Share #103 Posted April 8 (edited) Log entry 26 I have continued to work on the 18 foot cutter. Bending an fitting the tiny planks proved to be easier than I expected! Here are some pictures of the finished hull before sanding: I am quite happy with how it looks so far and with a little more taper of the first 3-4 planks it would have been possible to avoid using stealers altogether. I managed with just two. The plan is to paint the hull below the waterline as per the instructions, so it matters little anyway. This is a really nice little mini project within the bigger build! BR TJM Edited April 9 by TJM wvdhee, Blue Ensign, rcweir and 5 others 8 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
wvdhee Posted April 8 Share #104 Posted April 8 Looking nice! TJM 1 Quote Walter. Current build: Thinking about it Finished build: HMS Flirt Link to comment Share on other sites More sharing options...
TJM Posted April 13 Author Share #105 Posted April 13 Log entry 27 Just a small update on the cutter. The outside has been sanded an the temporary bulkheads removed without issues, much to my relief! Now to decide how much cleaning on the inside to do. It is very difficult to sand properly and the material is very thin already... TJM KARAVOKIRIS, mugje, wvdhee and 5 others 8 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
TJM Posted April 15 Author Share #106 Posted April 15 Log entry 28 the cutter is close to completion. I am missing the top bulwark (if that is the correct term....), painting and attaching the rudder and the oars. Cochrane paid a visit to inspect the progress (though he is still in a... pale state himself!). It is not perfect and the macro shots are harsh on it! From a reasonable viewing distance, I think it looks ok. It will make for a great upgrade to the deck of Flirt, for sure! BR TJM Thukydides, Mr Whippy, KARAVOKIRIS and 1 other 4 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
TJM Posted April 19 Author Share #107 Posted April 19 Log entry 29 The cutter is now completed and installed on the deck. I am really happy with the decision to add this, and to me it was definitely worth the time and effort. As you see, Cochrane has also gotten some colours. I am severely out of practice when it comes to miniature painting at this scale. Faces and eyes are never easy at this scale, but I used to be able to do better! 10 years ago... Anyways, he is just there for scale, so this will have to do. Now I can continue with the bowsprit boom and rigging. BR TJM Mr Whippy, ccoyle, Moonbug and 9 others 12 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
TJM Posted April 29 Author Share #108 Posted April 29 Log entry 30 Rigging of the bowsprit is now complete: It went well overall, though it is difficult to get to some part of it! How @Thukydides and others manage to make such beautiful knots and splices at this scale is beyond me! Hats off to you! But from a few feet away, I am happy with how my efforts are turning out. Now, on with the yards. BR TJM Thukydides, ccoyle, Ryland Craze and 6 others 9 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
wvdhee Posted April 29 Share #109 Posted April 29 Looking great! Some of these riggers here are insanely good indeed yes 😉 TJM 1 Quote Walter. Current build: Thinking about it Finished build: HMS Flirt Link to comment Share on other sites More sharing options...
TJM Posted May 9 Author Share #110 Posted May 9 Log entry 31 It has been a while since my last post, but I have not been idle! It is just that progress is slow for me at this point of the build and I have not had much to show until now. I have made and mounted the yards on the foremast: I am excited to see the final 'shape' of the ship starting to appear, thought a lot of rigging is still missing. Now I just need to repeat the last week's work to get the main mast to a similar state! BR TJM Blue Ensign, mugje, whitejamest and 4 others 7 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
wvdhee Posted May 9 Share #111 Posted May 9 Looking great! It's a lot of rigging yes 😉 TJM 1 Quote Walter. Current build: Thinking about it Finished build: HMS Flirt Link to comment Share on other sites More sharing options...
Thukydides Posted May 9 Share #112 Posted May 9 Looking very nice. The rigging is my favorite stage (apart from the ratlines) for this reason. You start to see the ship come to life. Every block and line you add makes a difference. Nipper, TJM and wvdhee 3 Quote Current build: HM Cutter Alert (Vanguard Models) Link to comment Share on other sites More sharing options...
TJM Posted May 23 Author Share #113 Posted May 23 (edited) Log entry 32 The yards are now done! I must admit that preparing the second set for the mainmast was not the most interesting part of this build. I think I am more of a 'hull guy' than a 'rigging guy'... But it is done and I a happy with the result! Apart from the anchors and the swivel guns, this concludes the building of parts and all that remains now is three plans of standing and running rigging. And while I am sure some challenges will present themselves, I am looking forward to this process as there is not much exact repetition and every line will add a new feature to the model. I hope to make more frequent updates than of late in this part, as there will be more visual progress to show. BR TJM Edited May 23 by TJM chris watton, Thukydides, wvdhee and 5 others 8 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
TJM Posted May 26 Author Share #114 Posted May 26 Log entry 33 I have now added the main and main preventer stays, including the first of the crowsfeet. It was a bit fiddly to thread the thin crowsfeet line through the bulwark, and I think it is a bit longer than it should strictly be, but I won't redo it. I will just make the foremast crowsfeet a matching length . BR TJM DB789, rcweir, dunnock and 7 others 10 Quote Current Build: HMS Flirt 1782 - Vanguard Models - 1:64 Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.