Chuck

Looking good so far...dont worry about the warped BF....You can straighten that out quickly with the filler blocks as was mentioned.  Enjoy the model and dont hesitate to ask any questions.  
 
Chuck

Thanks...I am fixing up the wales as we speak.  I will post another picture soon after its done.  I noticed after I posted the photos that that I didnt take the wales down at the bow enough before painting them.  Basically, in actual practice,  the wales would fit into the same rabbet.  Therefore they would not be thicker than the surrounding planking at the bow where it enters the stem rabbet.  They gradually reduce in thickness until they are the same as the surrounding planks.
 
This is a nice little detail that no one would probably ever notice but after its done it will make the model even more historically accurate.  I am reducing the thickness right now and will repaint.
 
See this contemporary model from the rogers collection...notice how the wales dont stand proud of the planking along the stem rabbet.   They are flush....and all fit into the rabbet nicely as compared to my model which will soon be all fixed up.  This is true for most ships during this period including frigates like the Winchelsea.  But because its one of those little details often overlooked...I always forget.... and have to go back and fix it later.  Its a carry-over habit from my kit building days where this is never mentioned.
 
I also included a picture of a mermaid class frigate 1780ish.   Look at the stem where the wales enter the rabbet.
 
 
 

 
Chuck

I dont think so....You should be OK.
 
Chuck

I dont think so....You should be OK.
 
Chuck

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

Thanks...I am fixing up the wales as we speak.  I will post another picture soon after its done.  I noticed after I posted the photos that that I didnt take the wales down at the bow enough before painting them.  Basically, in actual practice,  the wales would fit into the same rabbet.  Therefore they would not be thicker than the surrounding planking at the bow where it enters the stem rabbet.  They gradually reduce in thickness until they are the same as the surrounding planks.
 
This is a nice little detail that no one would probably ever notice but after its done it will make the model even more historically accurate.  I am reducing the thickness right now and will repaint.
 
See this contemporary model from the rogers collection...notice how the wales dont stand proud of the planking along the stem rabbet.   They are flush....and all fit into the rabbet nicely as compared to my model which will soon be all fixed up.  This is true for most ships during this period including frigates like the Winchelsea.  But because its one of those little details often overlooked...I always forget.... and have to go back and fix it later.  Its a carry-over habit from my kit building days where this is never mentioned.
 
I also included a picture of a mermaid class frigate 1780ish.   Look at the stem where the wales enter the rabbet.
 
 
 

 
Chuck

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I dont think so....You should be OK.
 
Chuck

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

Thanks...I am fixing up the wales as we speak.  I will post another picture soon after its done.  I noticed after I posted the photos that that I didnt take the wales down at the bow enough before painting them.  Basically, in actual practice,  the wales would fit into the same rabbet.  Therefore they would not be thicker than the surrounding planking at the bow where it enters the stem rabbet.  They gradually reduce in thickness until they are the same as the surrounding planks.
 
This is a nice little detail that no one would probably ever notice but after its done it will make the model even more historically accurate.  I am reducing the thickness right now and will repaint.
 
See this contemporary model from the rogers collection...notice how the wales dont stand proud of the planking along the stem rabbet.   They are flush....and all fit into the rabbet nicely as compared to my model which will soon be all fixed up.  This is true for most ships during this period including frigates like the Winchelsea.  But because its one of those little details often overlooked...I always forget.... and have to go back and fix it later.  Its a carry-over habit from my kit building days where this is never mentioned.
 
I also included a picture of a mermaid class frigate 1780ish.   Look at the stem where the wales enter the rabbet.
 
 
 

 
Chuck

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

Thanks...I am fixing up the wales as we speak.  I will post another picture soon after its done.  I noticed after I posted the photos that that I didnt take the wales down at the bow enough before painting them.  Basically, in actual practice,  the wales would fit into the same rabbet.  Therefore they would not be thicker than the surrounding planking at the bow where it enters the stem rabbet.  They gradually reduce in thickness until they are the same as the surrounding planks.
 
This is a nice little detail that no one would probably ever notice but after its done it will make the model even more historically accurate.  I am reducing the thickness right now and will repaint.
 
See this contemporary model from the rogers collection...notice how the wales dont stand proud of the planking along the stem rabbet.   They are flush....and all fit into the rabbet nicely as compared to my model which will soon be all fixed up.  This is true for most ships during this period including frigates like the Winchelsea.  But because its one of those little details often overlooked...I always forget.... and have to go back and fix it later.  Its a carry-over habit from my kit building days where this is never mentioned.
 
I also included a picture of a mermaid class frigate 1780ish.   Look at the stem where the wales enter the rabbet.
 
 
 

 
Chuck

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I added the first two strakes below the wales.  This was to get the drop plank out of the way.  The drop plank was shaped from a piece of card stock first just to get the hang of it.  After I was satisfied that it fit OK I  cut the real ones from wide stock the same thickness as the planking.  They were pre shaped as you can see.  You can also see my pencil on the edge to simulate the tarred seams. Now I will line off the remainder of the hull into two belts and finish the planking.  I also painted the first of many layers of red paint on the counter at the stern.
 
Chuck
 

 

 

 

 

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!

I have started to line out the hull for planking.   There are 20 strakes under the wales.   The first two are already done....those were the ones with the drop plank.  So I measured midship for the remaining 18 strakes.  They will be 3/16" wide.   Interestingly,  the strakes fit perfectly as they did on the contemporary draft.   There will be just two belts of strakes.   The first will have the remaining 8 under the wales.  The bottom belt will have ten.  Basically the hull was split in half down to the bottom of the square tuck as shown in that contemporary planking expansion.
 

 
I used black line tape to split the hull into the two belts.  I am spending a great deal of time examining it from all angles until I am pleased with it.   Then I marked along the tape and removed it.  All there is left to do is to take the space remaining in belt one on each bulkhead and transfer it to a tick strip.
 

 
The tick strip is divided into eight with the help of the planking fan.   Then the tick marks are transferred back to that bulkhead.  Once again I am amazed at how the cutter is so well designed by the naval architects.  Almost every bulkhead except for the four forward bulkheads have strakes exactly 3/16" wide.  Its a straight run to the square tuck with 3/16" planks.  No tapering/widening required in this first belt . Only those at the extreme bow need to be tapered which is a huge time saver.
 

 
This will not be the case in the lower belt.  The strakes will get wider at the stern as they run off the hull and also require tapering at the bow.  But it should be a very very close match to that original planking expansion for 1806.  Yippee for me.  It all worked out.
 
I also started fixing the wales at the bow which you can see in the photos.  They are now the proper thickness entering the rabbet or nearly so....almost there!!