donrobinson

Looks and sounds like a good wood, even used for boat building . I would certainly give it a try

Thanks David, you are soooo right about it being never ending 

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Thanks David, you are soooo right about it being never ending 

Thanks Dave. Yes I have a mill also they are both Sherline the lathe is a 4400 and the mill is a 5400, if you are thing of buying get one of their packages that come with accessories. I also highly highly recommend getting the digital read out at the same time, it really helps with accuracy and is a real saviour when it comes to repetitive cuts.  

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Should be fun to watch this one come together

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Thanks David, you are soooo right about it being never ending 

Thanks Dave. Yes I have a mill also they are both Sherline the lathe is a 4400 and the mill is a 5400, if you are thing of buying get one of their packages that come with accessories. I also highly highly recommend getting the digital read out at the same time, it really helps with accuracy and is a real saviour when it comes to repetitive cuts.  

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Thanks David, you are soooo right about it being never ending 

Thanks Dave. Yes I have a mill also they are both Sherline the lathe is a 4400 and the mill is a 5400, if you are thing of buying get one of their packages that come with accessories. I also highly highly recommend getting the digital read out at the same time, it really helps with accuracy and is a real saviour when it comes to repetitive cuts.  

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Hey Mike get it down, it is real good stress relief!
 

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Thanks Dave. Yes I have a mill also they are both Sherline the lathe is a 4400 and the mill is a 5400, if you are thing of buying get one of their packages that come with accessories. I also highly highly recommend getting the digital read out at the same time, it really helps with accuracy and is a real saviour when it comes to repetitive cuts.  

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Good morning everyone, I hope all is good and you are ready for another day of modelling. thanks to all for visiting.
 Well another milestone has been reached. Planking is finally complete! After approximately 1200 individual planks, two layers on hull and two layers on deck, this part of the build is now behind me. I opted not to simulate caulking as I usually don't really care for it, however, with my deck I am realising maybe I should have. Looking at my hull I thought there was enough definition between the planks but for some reason the deck is not so. It is very hard to see the butt ends and it almost looks like it maybe one solid sheet of wood. At any rate I am not about to tear it up. As of now it has two coats of wipe on poly and I will put on another two or three.
 The next step will be installing the covering board or waterway which will entail laterally bending a 6 mm plank to the shape of the stern, so we'll see how that works.
 Installing the planking
I used Weldbond glue, ca glue is not required for this step.  Weldbond, with a little burnishing, adheres in seconds proving to be adequate as I had no lifting of the planks after installation.
 Here are a few pictures:
 

Here is my new found plank shear, works great for cutting long angles. I recommend for those of you who have admirals to wait until she is gone before using this tool
 

And here it is in place, well that is not quite true as the one shown above had the glue applied to the wrong side!!
 

This is the burnishing tool I use. Simply just apiece of 13 mm (1/2") square stock. Doing this helps spread and level the glue and flattens out the plank. Sanding and  scraping was so much easier, I think I spent a maximum of 20 minutes of sanding the deck. Well worth the effort to try this if you are not doing it already.
 

 
 As you can see there are no real defined planks or butt ends, but trust me when I say it is a four plank shift and all shift lines are straight 
 
 That's it for today, I hope you enjoyed. Thanks for stopping by and we'll see you soon

Looks like you are getting it done, good stuff.