Trussben

Thank you Jim...
 
I have completed all of the hatches, gratings and partners to be placed on deck.  You have seen how the gratings were made.  The two hatches are pretty similar.  The only difference is they have cover boards rather than gratings within in the coamings.
 
 The photo below shows the laser cut coamings assembled.  There is no need to remove the laser char from the lap joints at the corners.  In fact it probably isnt a good idea at all.  They are precision cut so you end up with a perfectly squared up coaming the correct size.  You can and should sand both sides of the sheet before removing these laser cut parts to clean the char from those sides.  Just glue them up using the same right angle jig provided earlier.   Then sand the char off the top of the completed coaming being careful to keep the round-up consistent. 
 
You can see the smaller hatch completed.  The larger one shows the three cover boards also laser cut waiting to be glued into position.  But this you will also note the ledge created on the inside of the coaming that the cover boards will sit into.  These are laser cut for you and can be glued on the port and starboard insides of the coaming.
 

This photo shows the three coverboards in the coaming.  They are pretty thick, but only so they are flush with the center of the coaming to allow for the round-up.   The round-up along the sides of the coverboards should be sanded flush to the top edge of the coamings along the P & S sides.  I know some folks like to show one or two coverboards off the coaming.  You can do this if you want to.  But then you should sand that roundup into the bottom of the coverboards as well.   But I will show them all in place like the contemporary model.
 

To finish off the hatches...round off the corners using the right angle jig like you did for the gratings.   Trim them down to the top of the deck planking.   The bolts were added using black fishing line in the same way.   The iron ring for handles were made just like those on the lower platforms.  Exactly the same.
 

Also shown in the photo above are the mast and capstan partners.   These are completely laser cut for you.  They have etched lines to show the separate sections.   All you have to do is sand them clean and round off the corners as described earlier for the capstan partners only.  Soften the top edges as well.  Add the fishing line bolts and the eye bolts on the main mast partners.  Now some of these can be glued onto the model.  They are all ready to go so you can start planking the decks.
 
BUT there are a some like the main mast partners and capstan partners that need some extra work.   I will describe that next.   For example the elm pump tubes below the main mast partners and the capstan drum as well.
 
More to follow...but here is a photo with the all of the hatches, coamings and partners simply test positioned on the model.  They are not glued into position yet.   I did however glue the smaller grating and coaming on the forecastle deck in permanently....those are all finished up.  Its getting there!!!
 

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Finishing up Chapter5 with the gunport lids and I thought I would share how I make these.

1. Scotch tape is placed over each of the gunports and then the outline of the port and the position of the plank seams is traced onto it with a pencil.
2. Pieces of the correct width wood to match the planking widths are edge glued together about 1” wide and then the Scotch tape is pulled off the hull and aligned to the wood seams.
3. I roughly sand down to the outline of the outside of the port, and then fine sand while checking the fit until I get a snug fit it the port it is intended for.
4. Add the backing piece to each and paint the insides red.
 

I had to clean up the Dockyard before going on vacation, but thought I would post a couple of pictures of the two models, both in the same scale and of roughly the same timeframe - 1764 for Winchelsea and 1776 for Pegasus.

I am just about to post an update with those...LOL
 
The gratings for Speedwell are different but the same basic concept.  They are a different scale to reflect the larger size needed.  They will have 1/16" square openings which at 3/8" scale would be a 2" hole.  Just right and exactly the same number of holes as the contemporary model.
 
These will all be included in the chapter along with the jig needed.
 
I will have construction pics really soon.
 
I have been distracted lately with the topic on the SOS where the staff and admin are trashing this project relentlessly....but its a lot fun to watch.   Many of you guys have sent me messages alerting me about it.
 
I have to thank Ben however for being a brave soul to have something nice to say about it knowing he will get the wrath for it.   I must be the worst kit designer in the world if you read some of that stuff over there.  But seriously...dont put yourself out there because if you do say anything positive about Syren or any of my projects on SOS they will lambaste you.  So no worries.   Dont put yourself in that position.  Its not worth it.   Most folks know its all nonsense.  And I am well aware.  But thanks for the positive notes of private support.
 
Anyway...back to building gratings.

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Finishing up Chapter5 with the gunport lids and I thought I would share how I make these.

1. Scotch tape is placed over each of the gunports and then the outline of the port and the position of the plank seams is traced onto it with a pencil.
2. Pieces of the correct width wood to match the planking widths are edge glued together about 1” wide and then the Scotch tape is pulled off the hull and aligned to the wood seams.
3. I roughly sand down to the outline of the outside of the port, and then fine sand while checking the fit until I get a snug fit it the port it is intended for.
4. Add the backing piece to each and paint the insides red.
 

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

finishing up treenailing
 
ben

Thanks Greg, that’s high praise from you!
 
ben

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

You gotta love seeing the "Byrnes Bench"!!

Great News Ben...Glad to see you almost making sawdust again.

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Well the move was completed after our new home was built on Oak Island.
The new model workshop/office is far smaller than my previous one at only 13x13 but I’m using shelving and other things to maximize space which is ongoing.
Winchelsea is now waiting for me to start Chapter 7 on the Quarter Deck hopefully in the next couple of weeks as soon as I find all the parts!

Channels
 
Initial progress on channels, a really fun opportunity to cut away some of that moulding I so lovingly added a long time ago.

But before starting that I decided to bite the bullet to remove and replace the port lids. As I’ve mentioned a few times I have broken and glued back these lids too many times to count, all of course due to carelessness. It took some delicate work to remove them and the hinges without damaging the hull, especially the friezes.
 
This time I used the wider, thicker hinges @Chuck offers. Unlike I failed to do before I kept these movable rather than fixed.  I can now display these more like the right most port. My lesson learned is to install the port with both ends of the hinge on the lid, not one part on the hull and the other on the lid then threading the wire to connect them. This time I was able to keep the hinge tight enough to hold position. My first effort ended up with ‘floppy’ lids so I had to glue them into a fixed position, and by consequence made them vulnerable to my careless movements.
 
Though it took several days it was a good call to take this step back and get a better result. I’m happy to report the friezes all survived as did my sanity.

Well the friezes survived around the ports anyway.  Cutting away moulding the exact width and shape needed for the channels was pucker time, go slow, measure once, twice, three times before cutting, did I mention go slow. @FrankWouts was wise to factor this in at the time he installed his moulding, wish I’d thought of that.
 
I did remove and replace the frieze below the fore channel, it didn't prove necessary for the main and mizzen.

The beauty of this forum is the willingness to share means and methods. Something I always try to do and certainly take advantage of myself. This surgical tool, for podiatry I think, is absolutely perfect. My thanks to @Blue Ensign for sharing it. Two choices for replaceable blades: The wider chisel blade is thin, sharp and the perfect width for pushing through the moulding, keeping a clean edge on the remaining moulding either side. The smaller blade that opens up the slot for the strap perfectly. I have used this tool repeatedly for many varied purposes when my even my mini-Veritas chisels (@DelF) prove to large. A multi purpose sharp, light tool for model work. I have not yet tried them on my feet.
 
I have a wood chisel set for my lathe that until now were a bit too large to be useful. However one of those with a tight, sharp curved edge was perfect to notch and shape the moulding to match the channel. You can see the wood handle in the background, I failed to include it in the photo.
 
The tall height gauge, courtesy of @Stuntflyer, was very helpful in keeping the channels level with the waterline, I added the bubble level to make sure it was first level itself.  I need a better platform for it than a bowl, but it does the job. The tumblehome of the hull distorts what level seems just looking at it, the gauge brings it to actual level.

Long ago I acquired ebony deadeyes I wanted to use, however the center diameter of these proved too large for Chuck’s nice acrylic strops. So after splitting a few to learn that I went to Chuck’s make your own 5mm and 6mm versions. I still had a desire to go with ebony, but didn’t like my result just painting them black so I went with this ebony wood dye. With the thickness of water it takes 4 coats (and maybe still one more) to get them there, I like the  resulting look. It’s hard to tell in the photos but the boxwood grain still shows through and they look more “natural,” not perfectly black. The little paint stand is a strip of wood with the mill cutting a groove its length.
 
I didn’t take any photos of constructing the actual channels. Not much to it, just removing char, minimal shaping, and gluing together the three layers, and of course multiple coats of WOP.



So here where it stands. I’m going to wait until I have all the 5 and 6 mm deadeyes finished and both port and starboard channels installed before finishing these (including straightening the smiling faces) to ensure uniformity. Not too much to go on chapter 11 after that, I’ve been working on the gangways, posts and ladders in parallel to the channels so it's fitting and mounting them. I’m of mixed thoughts on the swivel guns - so decision deferred for now.
 
As always thanks for stopping by - I appreciate your taking the time with your likes and comments.

Hi Alan,
 
I feel your pain, I think I have redone parts of my Indy plans at least 3 times up to now, but it does make me much faster the second/third time around and I understand a lot more each time through. Steep learning curve with this stuff.
 
Ben