RGL
-
Posts
5,348 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by RGL
-
I reckon dark gloss green would work too, it is personal taste really as to where you display it so it looks right -
OK, pointy end of the ship done finally. I've pretty much replicated the AOTS for all the stays and running rigging.
-
I really have no idea why they are set up that way but I don't think if worry about it too much, it won't get in road of any of the other rigging at all.
-
Oh yes, 5-0 and Thankyou skull. I'll take some more photos if you wish with a ruler for dimensions if you wish, I imagine the angles will vary with each kit. I'll finished the rigging on the boom which I'll attach tomorrow.
-
The bowspit cap was cut from an off-cut of walnut that sits just outside the bees (about 2mm) - see photo. It sits at 90 degrees to the waterline but the angle at the top and bottom and the two holes run parallel to the angle of the bowspit. Done with a simple lead pencil and a sanding block to get the dimensions and angles correct. I drilled 2 holes and widened them, the lower one square and the upper one round at the angle of the bowspit. I then cut a small groove for the flagstaff and used a microfile to widen it to fit to seat 1/2 the circumference of the flagstaff. You then need 6 rings for blocks and rigging.
-
I have no idea how the silly smiley face got there.
-
Make sure to do a dry fit of the topmasts before you fit it all so they a) fit and sit square within the width of the inner tops hole. I did the fit which worked at first, then after all the shrouds went on it can be one a very tight fit.
-
Wow
-
I used the CC Photo etch fret. The crows feet thingy does not have enough holes! You'll have to do one by hand.
-
Ok, the whole mast tapers for the cheeks, with the green bit being full circumference. I did it on the lathe. I filed the sides above the green for the cheeks so they are fairly flush. The woulding was filed into the cheeks and used ratan for the hoops. The metal bands were just cut to appear as if they go under.
-
The "leather" liner is copper tape painter brown and the netting is commercial from Cornwall. I was going to try and hand sew it but it would have looked like crap at this scale. I did about 3 versions to get it right whilst I was watching the 5th test.
-
Bowspit cap, and horses and netting. As I said to slog I attached the blocks first to the cap. I've been dreading this part for years, but it came off quite easily really, only a days work in it for the netting.
-
Um, not sure what you mean, but this is how I did mine,
-
Sweet, a whole room. Off to the porno shop for married blokes then (Bunnings)!
-
This is the first Atlantic kit I have seen on this forum (or any other) I've seen, and the most beautiful ship. I'll be watching this with interest as it will be my next build after the Endeavour.
-
I hope your new place is planned around the ship!
-
Nice and square, but I'd do all the rope work and blocks before you stick it on for good
-
Last post of the year I promise! Bit of serendipity today as I actually read the plans and looked at the replica and the Topgallant shrouds have no ratlines! I'm finished with them! Shrouds and backstays in place. Lots of work on the bowsprit before I can add the last stay. next year it is.
-
Probably a bit too tight as it does kink a bit. The first shroud needs to be served all the way down to the deadeye to stop wear on the sail. I didn't fix my tops until I'd finished the shrouds as it let my fat fingers in to seize them. That being said, I never did get the deadeyes aligned properly but "meh"! At 1/64 some things just won't matter as there whole rigging thing makes it look so busy. Janos Caroline is just so perfect and neat it makes mine look like the cat did it. I've almost finished to top gallants so only a few ratlines to go.
- 517 replies
-
- 1
-
-
- Endeavour
- Artesania Latina
- (and 1 more)
-
Such a detailed ship, the amount of work is mind boggling. Well done
-
Looking good mate, I also love your tool box, I reckon you spent hours on that. Let the pain begin for shrouds and ratlines!
-
Nice work, good to see you back
-
There is a sense of achievement finally fitting the topgallants. The topgallant futtock shrouds and thimbles were attached first which gets really fiddly seizing them properly to the Topmast shrouds. Strangely, the masts ended up aligned! 12 shrouds and 4 backstays to go. Finally given the Endeavour's strong ties to Australia, a boxing day BBQ is always on the cards, so the BBQ photo. Hope you all had a happy Christmas.
-
Something completely different! I like it!
-
Looks really good!
Our Emblem ®
