EdT

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed

Young America - extreme clipper 1853
Part 238 – Head Sails Running Rigging
 
Each of the three stays described in Part 235 carries a triangular headsail.  Each of these sails is rigged with three lines of running rigging – a halyard to raise the head of the sail along the stay, a downhaul to bring the head down, and a double sheet to restrain the clew of the sail on the windward side.  When bent to the stay, the tack at the lower end of the sail is tied off low on the stay.  Then as the luff of the sail along the stay is secured with rope "hanks" the halyard is hauled up to raise the sail along the stay.  Both the halyard and the downhaul are shackled to the sails head cringle.  On the "unsailed" model, the halyard and downhaul eye splices are secured to the shackle, which is "stopped" to the lower end of the stay with a short length of rope as shown in the first picture at the base of the topmast stay.
 

 
In the picture the smaller downhaul is led down and through a single block back to its belaying point on the forecastle.  The next picture shows the lower ends of the inner and outer jib stays rigged in this manner.
 

 
The downhauls and halyards for the topmast staysail and outer jib lead back on the starboard side and those for the inner jib are rigged on the port side.  The next picture shows the three halyards where they pass through blocks hooked under the topmast trestletrees.
 

 
The lines lead down through fairleads in the top to the fife rails below.  The next picture shows the block arrangement at the topmast head, a double block on the starboard side for the staysail and outer jib halyards and a single block on the port side for the inner jib halyard.
 

 
The next picture shows the staysail and outer jib halyards belayed on the fore mast fife rail.
 

 
As will be seen in the next picture, the rope coils on the rails are quite small because the halyards are fully overhauled along the stay when there are no sails.
 

 
The next picture shows the belayed inner jib halyard on the port side.
 

 
Conversely, most of the downhauls must be coiled at the belaying points so sufficient line will be available to run up to the head of the sails when they are hauled up to the tops of the stays, so the three large coils in the next picture contain sufficient line for that.
 

 
Finally, the sheets – a pair for each sail.  These are shackled to eyebolts on either side of the forecastle, run through bullet blocks at the ends of a double pendant shackled to the clue of each sail, and belay on cleats on the forecastle breast beam.  One side or the other is used, with the lee side slack.  On the unsailed model, I have omitted the pendants and intend to coil each sheet adjacent to its eyebolt as shown in the next picture.
 

 
The picture shows the starboard sheet for the topmast staysail secured to its eyebolt.  When passed through the pendant block on this side, this line would be belayed on the innermost cleat on the breast beam. Eyebolts for the other head sails are arranged to the left on the rail, astride the mooring cleat.
 
Ed
 

Young America - extreme clipper 1853
Part 237 – Fore Spencer Gaff
 
The term "spencer" describes gaffs rigged on masts with square sails – except for the spanker gaff at the mizzen.  They were used to support fore and aft sails that were occasionally used, or sometimes to suspend pennants to keep them out of the other rigging.  The fore spencer gaff is shown in the first picture.
 

 
The gaff is a small, very simple spar attached to the mast with a gooseneck/eye fitting.  Stops for the standing lift are roughly centered on the spar as shown in the picture.  The upper end of the lift has an eye splice shackled to the eyebolt in the top.  A stop cut into the end of the spar will take a doubled "vang" pendant pair with a single block spliced into each end.  The long pendants may be seen in the next picture.
 

 
Each vang pendant is attached to a simple whip, with the standing end seized to an eyebolt on the main rail.  The fall is belayed nearby on the main pin rail.  In the picture the falls are temporarily clamped to center the gaff.  The next picture shows them belayed to the main pin rails port and starboard.
 

 
The limited required movement of the gaff requires a relatively short fall, so the coil of rope shown in the next picture is fairly small.
 

 
The masking tape shown over the open beams, does not do a lot for the photographs, but my sanity demands it.  I finally acquiesced to this after yet another part dropped into the hold and could not be retrieved.  While it is relatively easy to blow out small bits of thread, the main mast fid did not respond to this.
 
Finally, a test for clearance around the outboard boats is shown in the next picture. 
 

 
I need to think about this and decide if a lead block would be appropriate for this relatively small line, perhaps on one of the backstays.  I love rework.
 
Ed
 

Young America - extreme clipper 1853
Part 236 – Fish Tackle
 
The fish tackle is a triple purchase tackle suspended by a hook from the pendant described in an earlier post.  A second, large hook is fastened to the lower block of the tackle.   The purpose of this gear is to lift the anchors to stow them on the forecastle or to move them to the catheads.  The required weight of anchor for a ship of Young America's tonnage would be about 5000 pounds, so even with the mechanical advantage of 6 of the triple tackle, several hundred pounds of force had to be applied to the lift – unless another tackle was added to the fall.  The first picture shows the large bottom hook and the 12" double lower block of the tackle.
 

 
I still have quite a few blocks left over from the 1:96 Victory model, so with some re-scaling I have not yet had to make any.  There will be plenty of that later.  The next picture shows the  lower block strapped to the hook and being secured to the tackle rope with two seizings.
 

 
The tackle fall is a 3½" rope spun to the ~1" (.016") diameter from 2 strands of No. 60 Crocheting cotton and dyed with non-fading natural walnut extract stain.  The small seizings are simply an overhand knot – pulled tight, wet with glue, and the ends sliced off later.  The next picture shows the other hook being strapped to the upper 12" triple block.
 

 
The block is held in a surgical clamp in a bench vise for this.  For this small strapping a single overhand knot simulates the eye seizing at the hook and another overhand knot serves for the splice of the strap under the block as shown in the next picture.
 

 
Dilute, darkened glue is applied to the splice to fix it. The excess thread is then sliced off.   In the next picture the tackle has been rigged.
 

 
The upper block is hooked to the pendant and the lower end is hooked over a leg the forestay.  The fall is belayed and draped for convenience over the forecastle rail – one possible configuration.  The next picture shows a closer view.
 

 
The coil of rope was made separately from a length of line that would be sufficient in using the tackle.  Every foot of lift would require hauling six feet of rope. The line was coiled around a dowel, wetted with diluted glue, shaped and allowed to partially dry before mounting.
 
 
Ed

Young America - extreme clipper 1853
Part 235 – Fore Topmast Stays
 
There are three forward stays from the topmast head to the bowsprit – the topmast stay proper, the inner jib stay, and the outer jib stay.  The first is the primary structural stay, consisting of a doubled 9" rope looped over the over the shrouds and backstays at the topmast head, then down and under opposite sides of the bowsprit with the ends brought up and seized to the opposite leg.  The two lines are brought together to form a collar below the crosstrees and also at the bottom above the seizings.  The collar is served and leathered and the lower ends are served on both legs up to the seizings.  The first picture shows this stay placed over the masthead after the tissue leathering was glued to it.
 

 
The collar is clamped where it will be seized together and the glue on the leathering was left to dry in this shape.  I used straight PVA white glue for this so when dry the collar will still be flexible.  In the next picture, the two legs of the stay have been passed under the bowsprit, in position for seizing.
 

 
The next picture shows a closer view of the lower area.
 

The two legs do not cross under the bowsprit, so one short leg is seized above the stay and the other below. In the next picture, three seizings have been put on each side and the two legs have been seized together at the top of the served areas.
 

 
Excess seizing thread and stay rope have yet to be trimmed off.  Brushing the seizings and the stay where the ends will be clipped with darkened wood glue will seal the serving and the seizing knots so the excess can be trimmed off.
 
 In the next picture the inner and outer jib stays have been served, leathered and put over the masthead and are clamped where the collars will be seized.
 

 
The leather is simulated on the glued-on tissue strips using acrylic artist's color.  The lower ends of these two stays are shown in the next picture. 
 

 
These each pass through sheaves in the bowsprit, under upper cleats on the martingale and are shackled to eyebolts on the hull – the inner jib stay on the starboard side and the outer on the port side.  After seizing the upper collars, they were pulled taut through the hull shackles and seized.  These stays are served from above the sheaves to their ends at the side.  The inner jib stay attachment is shown in the next picture.
 
 
 The stay is seized to a shackle fabricated with its eyebolt before insertion into the hull. 
 
These last two pictures and the next were taken after installing the fish tackle and some of the jib/staysail running rigging, so some of this appears in the pictures.  Each of these three stays carries a head sail.  This work will be described in later posts.  The last picture shows the ship with all the forward topmast stays rigged.
 
 
 
 
Ed
 

update :
 
Floor planks and 10 deck supporting pillars mounted....
 
Nils
 

 
 

 
 

 
 

 
 

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed

What a wonderful project, truly inspiring.
I haven't read every single page, just areas that apply to my own project, and have already learned and knowing now to proceed, I'll gladly follow your procedures.
Thanks to you sir, for sharing this wonderful adventure.
Greetings from Germany,
Michael

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed

Extraordinary metalwork, Johann.  Bravo.
 
 
Ed

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed

Goog morning

Thanks very much Keith,
 
am pleased you like the spindle fastening points....
 
the stb. floor half is now permanently planked and mounted. The pine-planks are 3 x 100 mm long and 0,7 mm thick. The three square  outcuts take up the gratings to the bilge. The overstanding outside edges of the floor will be trimmed off when the hull gets faired for planking...
 
Nils
 

the three gratings, per side, for access to the bilge
 

 
 

 
 

 
the glue is applied from underneath, once the floor half is correctly positioned
 

update...
 
cutting out the floor halves from 0,8 mm ply for the cargo hold bottom (still to be planked...), and attatching the brass M4 thread-plates under the floor for the stand`s two spindles..., also checking out the deck-supporting pillars midships...
 
Nils
 

card template halves... will do...
 

 
 

the threaded brass fastening plates are enbedded safely between supporting lugs...
 

dry fit of pillars, the floor halves can be slipped in through the frame deck-beams...
 

 
 

 
 

here one wooden floor half (with overlapping) braces in dry fit

Update...
 
put some more stringers on, mounted the fancy support brackets for the high poop-deck grating, and am shaping the card template halves for making the cargo hold floor. I think I need`nt remove the deck beams for doing so, the card templates and later the thin planked ply floor halves can easily be slipped in through the frames from above....
 
Nils
 

 
 

 
 

 
 

 
 

 
 

 
 
 
 
 

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed

beautifull, the rigging is fantastic

It's allways a pleasure, if I get an mail that you have prepared a new update of your fantastic build. I love the elegant clipper ships and hope that I will have in the future the possibility to build a model of one - perhaps Young America

Great info Ed, and you were very meticulous in your work - would never know that they had changed.  I will need to watch for similar lead issues when i get to the rigging.
 
cheers
 
Pat

Young America - extreme clipper 1853
Part 239 – Revisions - Spencer and Headsail Rigging
 
The running rigging described in the last two parts has been revised.  In the case of the spencer gaff the fall of the vang was obstructed by the outer boats on the skid beams.  To correct this, I added lead blocks to the forward topmast backstay and led the fall down to its pin through a fairlead on that stay.  The first picture shows the original configuration on the port side and the revision on the starboard side.
 

 
The revised rig retains the same eyebolt for the standing leg of the vang, which then passes through the block on the shortened pendant, then through the lead block and a fairlead, both on the forward topmast stay.  The fall then belays on the same pin as before.  The next picture shows the starboard lead block and fairlead.
 

 
The old rope coils and belaying were removed as shown in the next picture.
 

 
A cotton swab soaked in isopropanol was laid on the rope for a few minutes to soften the wood glue. The rope was then easily removed.
 
The other revision involved the halyards on the three headsails.  I initially considered three typical configurations for these – no blocks, a single block whip from the deck, and a single block at the head of the sail.  I installed the first, simplest method as described in Part 238.  Shortly after installing these, I thought more about this and was concerned about no mechanical advantage on these rather large sails.  In checking (belatedly) the 1870's photo of the ship in New York, the blocks at the lower ends of the stays are clearly visible.  So, that configuration has now been installed on all three stays.  The foot of the topmast stay is shown in the next picture after revision.

This may be compared with the first photo in Part 238.  The revised lower rigging of the outer jib halyard is shown in the next picture.
 

To avoid re-rigging the downhaulers, the lower blocks were strapped to the shackle in place – a most difficult task, especially with shaky hands. The shackle eye was tied first, then the splice at the base of the block.  The inner jib stay at the left of the picture has not yet been converted. 
 
The upper ends of the stays are shown in the next picture with the standing ends of the halyards tied to the stays.
 

The last picture shows all three halyards converted.
 

So, we are now back on track after a short detour.
 
Ed