Jump to content

Recommended Posts

Good evening everyone, 

 

As you can see by the photo this is the deck plan for my 1/32 trawler, there are a lot of pointy bits, which i guess woulld not happen, i am laying planks over this and woundered if any one had any idea how it should look, even though a lot of it will never be seen  is the decking plan wrong?

15589047470897715386278613933040.jpg

15589046012686936515452339025782.jpg

15589045288814090429738425108469.jpg

Link to comment
Share on other sites

From what I read, it is not angle that controls the decision to nib or not, it seems to be width, as John said above, when the plank must be narrowed to 1/3 it's normal width, nib. Some thought into what lies underneath, to nail to, is also important, hard to secure a pointed board and prevent leakage as the vessel works and the sun and cold have their way with it.     :pirate41:

Edited by jud
Link to comment
Share on other sites

Thank you 

 

I moved on to the boat deck to see if i could make any progress on this nibbling 

 

But i still think i am getting it wrong im not sure if i should be rebating into the margin as well, but for tonight i have had an attempt on scrap wood to fit the margin to the planking 

15589821565806015642323727013583.jpg

15589821020385714013927929127559.jpg

Link to comment
Share on other sites

6 hours ago, popeye the sailor said:

looks very good Kevin......you'll need to make the margin 'blanks' wider to make the indentions for the nibbing.  appears your working with a 4 mm margin.  although,  John's example has the diagonal cut meeting the next plank.  I've never done it myself either.

Agreed, but if the concept is correct then i will proceed with what i have started, to make the margins wider i think will interfere with everything that has to go on this area however when i do the Amerigo Vespucci i will do this system again 

 

Link to comment
Share on other sites

13 hours ago, Kevin said:

Agreed, but if the concept is correct then i will proceed with what i have started, to make the margins wider i think will interfere with everything that has to go on this area however when i do the Amerigo Vespucci i will do this system again 

 

 

19 hours ago, popeye the sailor said:

looks very good Kevin......you'll need to make the margin 'blanks' wider to make the indentions for the nibbing.  appears your working with a 4 mm margin.  although,  John's example has the diagonal cut meeting the next plank.  I've never done it myself either.

Appologies my friend i regretted saying that i would continue as i was going,  im here for advice so 3rd attempt, no margins yet 

15590697785496530187675188112161.jpg

Link to comment
Share on other sites

Thank you for the comments this is how i am tonight 

 

Another question would the same wood type be used on the margins, i am doing this in lime strips 1mm x 5mm and purchased 1mm lime plank but it is very very brittle and i think unusable was wondering if birch would look silly, also this will not be a pristene build but a well used working static cutaway trawler 

 

also would the margins ever be painted?

 

15591620047414118848692224907062.jpg

 

 

15591620977654189414911133435313.thumb.jpg.7a751b33633dad5ca990c8d3f776daf1.jpg

Edited by Kevin
Link to comment
Share on other sites

thank you everyone for the comments and PM's

 

Well i completed the boat deck planking, there will be a couple of small areas that are not cluttered with trawler gear

 

i dont think it turned out to bad, this is prior to any sanding

 

my next question is, should i treenail, and what would be the best best of going about it?

 

IMG_4276.thumb.JPG.27ac351341dc2b7a4437eb6c6248877c.JPGIMG_4290.thumb.JPG.80007f0be6bc13343ca9619c03e0debb.JPG

IMG_4291.JPG

Edited by Kevin
Link to comment
Share on other sites

  • 4 weeks later...

Hi Kevin - Your work looks really nice and far nicer than a trawler would be.  I think I prefer your version though as modern trawlers can be really basic vessels without much thought about the finer side of carpentry joints.  Its more about practicality over looks due to the battering they get whilst out at sea earning a living.  Your doing a great job and I'm looking forward to seeing your progress. 

Link to comment
Share on other sites

  • 4 weeks later...

Sorry i have just seen your post, the decking was another step going towards the dark side, so an opportunity to do something a bit different, lol only the readers of these forums will ever see her, so i dont have to face the rivet counters on the pond side or at a show, the build log continues as per the signature link 

IMG_4445.JPG

IMG_4562.JPG

Link to comment
Share on other sites

  • 6 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...