drobinson02199 Posted May 2, 2021 Author #31 Posted May 2, 2021 Deck fittings built and installed. Regards, David Wintergreen and Ryland Craze 2 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
drobinson02199 Posted May 7, 2021 Author #32 Posted May 7, 2021 I have now completed work on the hull. Added: Deadeyes on channels Cannons Stanchions and railing Anchor cable Some side rigging The manual says to wait to rig the anchors until the other rigging is complete (makes sense), but I installed the anchor cable across the deck and through the hawse because it would be tough to get at after the mast rigging is up. You can see the excess at the bow held with paper clips for later attachment to the anchors. Next step is the mast and yards. Regards, David AJohnson, oneslim, Dfell and 2 others 5 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
drobinson02199 Posted May 16, 2021 Author #33 Posted May 16, 2021 Mast is up and four shrouds rigged. There are two more shrouds on each side, but the ratlines only go across the first four, so easier to do the ratlines next before I put up the other two shrouds. Regards, David Dfell and Wintergreen 2 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
drobinson02199 Posted May 23, 2021 Author #34 Posted May 23, 2021 Ratlines are now done. They are done in a natural thread, and then dyed black. Now I can rig the last two shrouds on each side. Regards, David Dfell and Wintergreen 2 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
drobinson02199 Posted May 25, 2021 Author #35 Posted May 25, 2021 Remaining two shrouds rigged on each side -- they don't get ratlines. Also installed the shroud cleats. I haven't seen anything like these on other ships I've built, and I think they are kind of cool. The manual says paint them black, but as with the hull-mounted cleats, I left them unpainted and I think they will show better this way. Nothing is actually rigged to them in the finished model. Regards, David bruce d, PRS, Wintergreen and 1 other 4 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
Wintergreen Posted May 27, 2021 #36 Posted May 27, 2021 David, you're doing a fine job with the rigging. The ratlines looks absolutely smashing, nice and even all the way. Well done! drobinson02199 1 Quote Happy modelling! Håkan __________________________________________ Current build: Atlantica by Wintergreen Previous builds Kågen by Wintergreen Regina by Wintergreen Sea of Galilee boat, first century, sort of... Billing Boats Wasa Gallery: Kågen (Cog, kaeg) by Wintergreen - 1:30, Billing Boats Regina - 1:30, Billing Boats Dana,
drobinson02199 Posted May 27, 2021 Author #37 Posted May 27, 2021 Hakan: Thanks for the comment on my ratlines. I use a homemade jig that helps me keep the spacing uniform and the ratlines level. I have included a couple of pictures below. I find that I make a new jig for each ship because the spacing varies. Regards, David Wintergreen 1 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
DPhilbrick Posted May 28, 2021 #38 Posted May 28, 2021 This is looking amazing. Great work. drobinson02199 1 Quote
drobinson02199 Posted May 29, 2021 Author #39 Posted May 29, 2021 Installed the bowsprit and side rigging for it. The stays on each side of the bowsprit are the same thread that was specified for the shrouds. When it's under tension, it twists. So if you rig the blocks loose all the way (the way you'd do with a deadeye) and then tighten them, the block on the stay spins and the rigging between the blocks twists -- bad look. The way I solved it was to attach the thin thread to the eyebolt on the block attached to the stay, pass it through the block at the hull only, and then tension it. That causes the stay block to twist, and if you hold the twist there and then finish rigging the thin thread back through the block on the stay, the rigging aligns when you re-tension it and looks as you see in the picture. But it took some work to figure out a solution. Regards, David Wintergreen 1 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
drobinson02199 Posted June 3, 2021 Author #40 Posted June 3, 2021 Yards are now up, with sheets rigged to two of them. Regards, David bruce d and Wintergreen 2 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
Glenn-UK Posted June 3, 2021 #41 Posted June 3, 2021 Just discovered your build log. You are building a great model. I am building the Alert and I have just finished adding the hull decorations. drobinson02199 1 Quote Glenn (UK)
drobinson02199 Posted June 4, 2021 Author #42 Posted June 4, 2021 I've completed all of the stays. Some nice rigging at the bow. As I noted earlier, the heavier black threads twist when under tension, so the trick with those is to pre-tension them and then rig the blocks to other blocks. That keeps things straight when under tension. Regards, David bruce d, Wintergreen, AnobiumPunctatum and 1 other 4 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
zappto Posted June 5, 2021 #43 Posted June 5, 2021 wowy, great work. Will be a beautifull ship! drobinson02199 1 Quote Current build: Mamoli - La gloire 1778 Finished builds: Mamoli - Friesland 1663 Mamoli - Lexington 1776
drobinson02199 Posted June 8, 2021 Author #44 Posted June 8, 2021 Alert is finished! Nice kit from Vanguard Models and Chris Watton. A set of photos is in the Kit-Built Ship Gallery. Regards, David VTHokiEE, Oboship, Haliburton and 8 others 11 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
ccoyle Posted June 8, 2021 #45 Posted June 8, 2021 Over the years, you've had a lot of nice models take their turn on that shelf! drobinson02199 and bruce d 2 Quote Chris Coyle Greer, South Carolina When you have to shoot, shoot. Don't talk. - Tuco Current builds: Brigantine Phoenix, DS Børøysund
killickthere Posted June 18, 2021 #46 Posted June 18, 2021 Hello David, I'm very interested in building this model after I finish my Bounty launch. Your build is beautiful. One question... I noticed the cannons are not rigged. Any particular reason? Does the kit not come with the blocks and cordage to rig them? Thanks! Quote
drobinson02199 Posted June 18, 2021 Author #47 Posted June 18, 2021 Hi Killickthere: I don't have my manual any more to check, but I just looked at the pictures on the Vanguard site and they are not rigged on the model pictured. But there are eyebolts on each side of the cannon carriages for rigging, which I did install, so you can certainly do it yourself if you have some spare hardware -- and there may be enough spares in the kit to do it. I still have eyebolts left over (they are photo-etched brass). Hope this helps. Regards, David killickthere 1 Quote David Robinson Boston, MA area Completed: Constructo J.S. Elcano, Artesinia Latina Sanson, Dumas Mt. Washington, Bluejacket Nantucket, Amati Revenge, Artesania Latina King of the Mississippi, Amati Grand Banks Heritage 46, Amati HMS Fly, Amati Titanic, Dumas Chris Craft Commuter, Mantua Cutty Sark, Mantua Bruma, Kolderstok Batavia, Vanguard Models HM Cutter Alert, Caldercraft HMS Victory, Dumas USCG Fast Response Cutter Currently Building: Amati Bismarck
killickthere Posted August 10, 2021 #48 Posted August 10, 2021 Thank you David. Sorry I just saw this post. I just received my kit today, yippie! I will probably rig the guns. Thank you for the info. Thukydides 1 Quote
GrandpaPhil Posted August 10, 2021 #49 Posted August 10, 2021 Congratulations! Well done! Quote Building: 1:200 Russian Battleship Oryol (Orel card kit) 1:64 HMS Revenge (Victory Models plans) 1:64 Cat Esther (17th Century Dutch Merchant Ships)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.