DaveBaxt Posted May 25, 2021 Author Share #211 Posted May 25, 2021 27 minutes ago, Tim Moore said: Well done Dave! Congrats on pushing through all that rigging. Thank you Tim for all your help, especially with the rigging Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
DaveBaxt Posted May 25, 2021 Author Share #212 Posted May 25, 2021 41 minutes ago, Gregory said: A Very nice Bounty! I think you may have set a record for completing a kit, not counting James H. and his Vanguard prototypes.. Thank you Gregory for all your help and keeping an eye on my progress. Best regards Dave Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
Gregory Posted May 25, 2021 Share #213 Posted May 25, 2021 Any plans for your next ship? Quote “Indecision may or may not be my problem.” ― Jimmy Buffett Current builds: Rattlesnake On Hold: HMS Resolution ( AKA Ferrett ) In the Gallery: Yacht Mary, Gretel, French Cannon Link to comment Share on other sites More sharing options...
DaveBaxt Posted May 25, 2021 Author Share #214 Posted May 25, 2021 1 hour ago, Gregory said: Any plans for your next ship? Yes I have been looking at the Endeavour by Caldercraft due to local interest. However I understand it is quite a difficult model to build for a beginner. I won,t be starting my next model until October/November when the autumn begins to settle in. AJohnson 1 Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
Gregory Posted May 25, 2021 Share #215 Posted May 25, 2021 1 hour ago, DaveBaxt said: I understand it is quite a difficult model to build for a beginner. Who's a beginner? I think your experience with the Bounty should move you up a notch or two.. AJohnson 1 Quote “Indecision may or may not be my problem.” ― Jimmy Buffett Current builds: Rattlesnake On Hold: HMS Resolution ( AKA Ferrett ) In the Gallery: Yacht Mary, Gretel, French Cannon Link to comment Share on other sites More sharing options...
AJohnson Posted May 25, 2021 Share #216 Posted May 25, 2021 37 minutes ago, Gregory said: Who's a beginner? I think your experience with the Bounty should move you up a notch or two.. Agreed! I think you will be able to build an excellent Endeavour 👍 Well done on your Bounty build! 👏 Quote Andrew Current builds:- HM Gun-brig Sparkler - Vanguard (1/64) , HMAV Bounty - Caldercraft (1/64) Completed (Kits):- Vanguard Models (1/64) :- HM Cutter Trial , Nisha - Brixham trawler Caldercraft (1/64) :- HMS Orestes(Mars), HM Cutter Sherbourne Paper Shipwright (1/250) :- TSS Earnslaw, Puffer Starlight Link to comment Share on other sites More sharing options...
DaveBaxt Posted May 25, 2021 Author Share #217 Posted May 25, 2021 Thank you guys you are both very kind and it gives me confidence to proceed with the HMS endeavour. Best regards Dave AJohnson 1 Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
Gregory Posted May 25, 2021 Share #218 Posted May 25, 2021 Looking forward to your build.. You have several months to ask questions and prepare.. Don't wait till the build starts.. I wish more members would ask questions like you have during your Bounty build.. Quote “Indecision may or may not be my problem.” ― Jimmy Buffett Current builds: Rattlesnake On Hold: HMS Resolution ( AKA Ferrett ) In the Gallery: Yacht Mary, Gretel, French Cannon Link to comment Share on other sites More sharing options...
DaveBaxt Posted May 25, 2021 Author Share #219 Posted May 25, 2021 1 hour ago, Gregory said: Looking forward to your build.. You have several months to ask questions and prepare.. Don't wait till the build starts.. I wish more members would ask questions like you have during your Bounty build.. Funny you should mention that. I already have a few questions and I haven't seen the kit yet!. Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
Gregory Posted May 25, 2021 Share #220 Posted May 25, 2021 Just start a topic in the General Ship Model Kit Discussions Quote “Indecision may or may not be my problem.” ― Jimmy Buffett Current builds: Rattlesnake On Hold: HMS Resolution ( AKA Ferrett ) In the Gallery: Yacht Mary, Gretel, French Cannon Link to comment Share on other sites More sharing options...
ccoyle Posted May 25, 2021 Share #221 Posted May 25, 2021 Excellent work, Dave! Congratulations! DaveBaxt 1 Quote Chris Coyle Greer, South Carolina When you have to shoot, shoot. Don't talk. - Tuco Current builds: Brigantine Phoenix, Bf 109E-7/trop Link to comment Share on other sites More sharing options...
DaveBaxt Posted May 25, 2021 Author Share #222 Posted May 25, 2021 (edited) 22 minutes ago, Gregory said: Just start a topic in the General Ship Model Kit Discussions I already did a few days ago. I will of coarse add any question I may have, as they arise. I will eventually start another blog once I have purchased the Endeavour kit which should be sometime next month. I am also planning on buying either a drill press or even a milling m/c at some stage before I start building in the hope of producing better elements of the model . I also have a thread running on this subject too. Edited May 25, 2021 by DaveBaxt Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
Gregory Posted May 25, 2021 Share #223 Posted May 25, 2021 I will be watching.. I Don't have any experience with Caldercraft, but I think they are a cut above some kits i have worked on. I like the look of walnut, but you will find it's detractors among some ' purists '.. I wonder how it responds to " Chuck's edge bending method " ? LyleK1 1 Quote “Indecision may or may not be my problem.” ― Jimmy Buffett Current builds: Rattlesnake On Hold: HMS Resolution ( AKA Ferrett ) In the Gallery: Yacht Mary, Gretel, French Cannon Link to comment Share on other sites More sharing options...
LyleK1 Posted May 25, 2021 Share #224 Posted May 25, 2021 I wonder how it responds to " Chuck's edge bending method " ? I've been using Chuck's method on my Bounty build. Considering that I'm working with 5mm X 2mm walnut and in some cases 10mm X 2mm, it works well but it does take a little extra time. It takes about 20-30 minutes to soak a piece long enough to bend it and you may need to bend it twice to keep it from snapping! I use almost an exact set-up to Chucks except I use a sealing iron for heat. Check out my build log for more details and pictures if you're interested. BTW, Dave, your build is beautiful! Well done! The Endeavor is on my short list too... I'll be watching for your log! AJohnson 1 Quote Lyle "The only thing that stays the same is the constant state of change" Completed Builds: Occre HMS Terror - https://modelshipworld.com/gallery/album/2065-hms-terror-occre/ NRG Half Hull Project - https://modelshipworld.com/topic/23546-half-hull-project-by-lylek1-nrg/ 1:130 1847 Harvey - https://modelshipworld.com/gallery/album/2125-1847-baltimore-clipper-harvey-1130-scale/ Scott Miller's Sea of Galilee Boat - https://modelshipworld.com/topic/29007-sea-of-galilee-boat-by-se-miller-120-scale-lylek1/ In progress: Artesania Latina HMS Bounty - https://modelshipworld.com/topic/26817-hms-bounty-by-lylek1-artesania-latina-148-scale/ Waiting for dry-dock space: Model Shipways - USS Constitution Master Korbel - Cannon Jolle 1801 A Scratch build -TBD Link to comment Share on other sites More sharing options...
DaveBaxt Posted May 26, 2021 Author Share #225 Posted May 26, 2021 6 hours ago, LyleK1 said: I wonder how it responds to " Chuck's edge bending method " ? I've been using Chuck's method on my Bounty build. Considering that I'm working with 5mm X 2mm walnut and in some cases 10mm X 2mm, it works well but it does take a little extra time. It takes about 20-30 minutes to soak a piece long enough to bend it and you may need to bend it twice to keep it from snapping! I use almost an exact set-up to Chucks except I use a sealing iron for heat. Check out my build log for more details and pictures if you're interested. BTW, Dave, your build is beautiful! Well done! The Endeavor is on my short list too... I'll be watching for your log! Thank you Lyle for your input. I did exactly the same for the Bounty using a heating Iron and Chucks method of marking off and bending edge ways and as you say takes a bit more time but turned out quite good in the end. I will take a look at your log and compare notes haha. For the record the Bounty's first layer of planking is also Walnut where as the Endeavour is lime. The Bounty's first layer was also 6mm wide x 1.5mm thick which wasn,t without issue but I ended up soaking overnight as this seemed to be the only way to bend the planks on their edge. I did not need to do this with the second planking as it was only 0.5mm thick.The Endeavour's second planking 1mm thick so I might have to soak this too for sometime. Bestregards Dave Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
DaveBaxt Posted May 26, 2021 Author Share #226 Posted May 26, 2021 8 hours ago, Gregory said: I will be watching.. I Don't have any experience with Caldercraft, but I think they are a cut above some kits i have worked on. I like the look of walnut, but you will find it's detractors among some ' purists '.. I wonder how it responds to " Chuck's edge bending method " ? I used Chucks method of bending edgeways on the Bounty using 6 mm x 1.5 mm Walnut strips. and was not without its problemms. I ended up soaking the strips overnight , enough for the next day and this worked fine .At the time I was informed that there was minimum shrinkage with Walnut but I did use a heating Iron as well . The second layer was much easier although also Walnut was only 0.5mm thick and 4 mm wide. The Endeavours first planking is lime so hoping it will be easier to work with. Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
Baker Posted May 26, 2021 Share #227 Posted May 26, 2021 Well done, a very nice model. DaveBaxt 1 Quote Regards, Patrick Finished : Soleil Royal Heller 1/100 Wasa Billing Boats Bounty Revell 1/110 plastic (semi scratch) Pelican / Golden Hind 1/45 scratch Current build : Mary Rose 1/50 scratch große-jacht / Yacht D'Oro 1/50 Corel Gallery : Revell Bounty Pelican/Golden hind 1/45 scratch Shore leave, non ship models build logs : ADGZ M35 funkwagen 1/72 Einhets Pkw. Kfz.2 and 4 1/72 Autoblinda AB40 1/72 122mm A-19 & 152mm ML-20 & 12.8cm Pak.44 {K8 1/2} 1/72 10.5cm Howitzer 16 on Mark. VI(e) Centurion Mk.1 conversion M29 Weasel 1/72 SAM6 1/72 T26 Finland T26 TN 1/72 Autoprotetto S37 1/72 Opel Blitz buses 1/72 Boxer and MAN trucks 1/72 Hetzer38(t) Starr 1/72 Cleaning the 1/72 military collection Si vis pacem, para bellum Link to comment Share on other sites More sharing options...
Trond Posted May 26, 2021 Share #228 Posted May 26, 2021 Grats for finish the Bounty. You've done a marvelous job Dave. It really look nice. Looking forward to follow your next project. AJohnson 1 Quote Trond 'Patience Is a Virtue' Current Build: HMS Bounty - Billingboats Link to comment Share on other sites More sharing options...
DaveBaxt Posted May 26, 2021 Author Share #229 Posted May 26, 2021 9 minutes ago, Trond said: Grats for finish the Bounty. You've done a marvelous job Dave. It really look nice. Looking forward to follow your next project. Thanks Trond. I am still popping in to have a look at your progress from time to time Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
DaveBaxt Posted May 26, 2021 Author Share #230 Posted May 26, 2021 20 hours ago, LyleK1 said: I wonder how it responds to " Chuck's edge bending method " ? I've been using Chuck's method on my Bounty build. Considering that I'm working with 5mm X 2mm walnut and in some cases 10mm X 2mm, it works well but it does take a little extra time. It takes about 20-30 minutes to soak a piece long enough to bend it and you may need to bend it twice to keep it from snapping! I use almost an exact set-up to Chucks except I use a sealing iron for heat. Check out my build log for more details and pictures if you're interested. BTW, Dave, your build is beautiful! Well done! The Endeavor is on my short list too... I'll be watching for your log! I definately like your version of the Bounty with the open decks. It is a credit to the hobby. Hopefully one day I will return to the Bounty once again and have a go at the Artesinia Bounty once I have honed my skills a bit more. Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
LyleK1 Posted May 26, 2021 Share #231 Posted May 26, 2021 5 hours ago, DaveBaxt said: I definately like your version of the Bounty with the open decks. It is a credit to the hobby. Hopefully one day I will return to the Bounty once again and have a go at the Artesinia Bounty once I have honed my skills a bit more. I think your skill level is great! Good luck with your next build and stop by my log once in a while! Always appreciate feedback! DaveBaxt 1 Quote Lyle "The only thing that stays the same is the constant state of change" Completed Builds: Occre HMS Terror - https://modelshipworld.com/gallery/album/2065-hms-terror-occre/ NRG Half Hull Project - https://modelshipworld.com/topic/23546-half-hull-project-by-lylek1-nrg/ 1:130 1847 Harvey - https://modelshipworld.com/gallery/album/2125-1847-baltimore-clipper-harvey-1130-scale/ Scott Miller's Sea of Galilee Boat - https://modelshipworld.com/topic/29007-sea-of-galilee-boat-by-se-miller-120-scale-lylek1/ In progress: Artesania Latina HMS Bounty - https://modelshipworld.com/topic/26817-hms-bounty-by-lylek1-artesania-latina-148-scale/ Waiting for dry-dock space: Model Shipways - USS Constitution Master Korbel - Cannon Jolle 1801 A Scratch build -TBD Link to comment Share on other sites More sharing options...
DaveBaxt Posted June 15, 2021 Author Share #232 Posted June 15, 2021 And finally the displayed in her case Trond, GrandpaPhil, Gregory and 1 other 3 1 Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
LyleK1 Posted June 15, 2021 Share #233 Posted June 15, 2021 Very nice! DaveBaxt 1 Quote Lyle "The only thing that stays the same is the constant state of change" Completed Builds: Occre HMS Terror - https://modelshipworld.com/gallery/album/2065-hms-terror-occre/ NRG Half Hull Project - https://modelshipworld.com/topic/23546-half-hull-project-by-lylek1-nrg/ 1:130 1847 Harvey - https://modelshipworld.com/gallery/album/2125-1847-baltimore-clipper-harvey-1130-scale/ Scott Miller's Sea of Galilee Boat - https://modelshipworld.com/topic/29007-sea-of-galilee-boat-by-se-miller-120-scale-lylek1/ In progress: Artesania Latina HMS Bounty - https://modelshipworld.com/topic/26817-hms-bounty-by-lylek1-artesania-latina-148-scale/ Waiting for dry-dock space: Model Shipways - USS Constitution Master Korbel - Cannon Jolle 1801 A Scratch build -TBD Link to comment Share on other sites More sharing options...
GrandpaPhil Posted August 18, 2021 Share #234 Posted August 18, 2021 Congratulations! Well done! Quote Building: 1:64 HMS Revenge (Victory Models plans) 1:64 Cat Esther (17th Century Dutch Merchant Ships) Link to comment Share on other sites More sharing options...
DaveBaxt Posted August 18, 2021 Author Share #235 Posted August 18, 2021 3 hours ago, GrandpaPhil said: Congratulations! Well done! Thank you! Your reply is appreciated Morten and GrandpaPhil 1 1 Quote Completed St Canute Billings Dec 2020 Completed HMS Bounty Amati May 2021 Finished Currently building HM Bark Endeavour Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.