Jump to content
MSW Spring Donation Drive

mrcc

Members
 View Profile  See their activity

  • Posts

    418

  • Joined

  • Last visited

 Content Type 

Everything posted by mrcc

  1. mrcc
    Don't know why I was scared to tackle the tapering of the yards and masts without a mini lathe... So easy to do with a cheap mini plane and a bit of time and patience. I just divided the mast /yard into increments, knowing what my end diameter is and planed the furthest to the midway taking gentle cuts with the plane as to not gouge into the wood. I constantly measured with my caliper being careful not to take too much off and then sanded first roughly with 80 and then final sanded with 120 to get the perfect taper.
  2. mrcc
    Thanks Popeye for the input, I think I will affix the chains just above the strake and thus onto the hull, even though it may not be historically accurate. I think it will be impossible to find the chains to match should I wish to extend the chains by a link or two. The other problem with regards to tapering the masts are likely best tackled with a drill and the problem here is the main mast is a diameter of 12 mm which will not fit in the chuck but I am sure I will find a workaround. Cheers
  3. mrcc
    Still hemming and hawing over what to do with the masts... I have noticed with this hobby that the further you progress in skills, the more perfectionistic you become and with these masts, I feel I do not want to tackle them quite yet and I keep mulling over the fact that I should buy a proxxon mini lathe to truly do them justice. Anyways, one problem that I have from the picture below is that the chains don't reach as far down as they should according to the plans. My understanding is that they should anchor into the upper of the two lower strakes pictured. Either I put the series of strakes a bit to low and perhaps I put the chain plate a bit too high as well... and thus the problem. Question: just anchor them into the hull and don't worry about anchoring them into the strake or try and purchase the chains to match and extend them a bit further down. This is an old kit from Mamoli and it will be difficulty to find a perfect match of the existing chains.
  4. mrcc
    After lots of "hemming and hawing"... Should I buy a mini lathe or not... I decided to tackle the tapering of masts in the most basic way. I marked out the main mast at the point where the taper begins from 12 mm and ends at 5 mm on a piece of cardboard and dividing the total distance, that by the difference of 7 mm, marked out my hashmarks on the cardboard, and began with the mini planer to strip the dowel from the end to the base in ever less increments, constantly measuring with the caliper. I kept the dowel at about 1 mm larger than need and plan to final finish the taper with sandpaper... which I ran out of, thus the lack of pictures with final finished mast. This process took me all of 10 minutes with the new sharp planer that I had and was pleasantly surprised at how well it turned out. Glad I saved some money in the non purchase of the mini lathe but would still love to own one nevertheless.
  5. mrcc
    Thanks Ian/Popeye for the kind regards... I was Ian, going to put a Danish or Tung oil finish on until I saw your Brazzera finish... and that easily convinced me to do the wipe-on poly. Now I am contemplating what to do next with the masts and tapering of them. I feel a bit intimidated with the prospects as I will likely taper them with just a hand mini planer and sandpaper. Would love to invest in a proxxon mini lathe...
  6. mrcc
    As more evident on these images...
  7. mrcc
    And I used a contour gauge to mark out and notch the chain plates, also further notching out the spaces to allow the deadeyes to fit more easily, further adding a mahogany strip on the outside, prior to affixing the plates on the hull.
  8. mrcc
    And here are images of my hull with 3 coats of satin wipe-on poly. The images/photos are taken with the fresh, most recent coat of finish, and appear much more glossy than what they really are...
  9. mrcc
    Hi Scott, thanks for the kind compliments... I also peek in quietly to your Mamoli build log. Actually I found the castings to be very good in my kit. Thanks Ian, trying to keep up to your level of finish on the Brazzera. I will likely do 3 coats of finish and see how it looks. Do you think a 4th coat will add extra depth to the finish? Thanks Popeye, the finish is satin (Wipe-on Poly). The ship's boat are loose for now as I turn the S. Maria over and upside down to do my finish coats for the time being.
  10. mrcc
    Thanks again Popeye for checking in... On this update, I have to report that I spent hours getting the cap railings to fit properly. I would have to additionally say that I am now an expert at steam bending. The cap rails are beautiful beechwood strips and once soaked and steamed, and once bent on the flat iron, they contorted and twisted lengthwise. So with the main/middle deck and having the cap rails bent at each end with steam bending, I found them to be a real challenge to place them properly. The foredeck and half deck were relatively easy. The pictures below have the Humbrol varnish applied and look very good in my opinion.
  11. mrcc
    Hi Glenn, you have created such a wonderful build log... I love the historical details, the pictures of the real ship, planning and solutions above what the Billing kits allow, and the workmanship of course. Perfect in all regards!
  12. mrcc
    Thanks JB... The Mamoli kits build out very nicely in my opinion. Overall I am very happy with the kit... The instruction material is weak, also the setting of bulkheads and decking can be a real challenge at the beginning of the build to get right, given my older kit and non laser cut bulkheads... but once past these issues, the kit can really shine, especially with regards to the supplied strip wood and supplied castings.
  13. mrcc
    And here are some images of the decks with the railings installed, just recently varnished with Humbrol matt varnish. The lighting is perhaps not the best with these images...
  14. mrcc
    More details to report... Lots of fun adding some of the ornamentation to the ship. I believe the casting are a brass based metal, a soft, easy to bend material. I painted them with a primer and then added the acrylic paint colors according to my own instinct. The recommended color scheme by Mamoli is certainly not to my liking. I must admit that the castings are very well done and in my opinion are looking great on the ship.
  15. mrcc
    I think this is what you are looking for...
  16. mrcc
    Thanks Popeye, Mustafa for your fine compliments... much appreciated. The stove was the kit supplied stove, unaltered and unpainted. I was debating whether to accent some of the features of the stove with paint.
  17. mrcc
    And more details on the deck... the hatch, stove, and pinnace cradles glued down onto the deck.
  18. mrcc
    The windlass... the belfry parts...
  19. mrcc
    More time to post some progress... I am very happy how the smaller boats, the pinnace's came out. A few add on modifications compared to how Mamoli set them out to be built...
  20. mrcc
    Yes Ian, I was going to do Danish or Tung Oil but your finish with Wipe on Poly is stunning... Did you wipe or brush it on?
  21. mrcc
    Wow, what an amazing job Ian... Very nice! One quick question, how did you do the finish on the hull? Wipe-on Poly? It's perfect!
  22. mrcc
    I agree, Beautiful!
  23. mrcc
    Thanks Slideways... do not know if I would say with ease. Cheers!
  24. mrcc
    Another minor issue once found attaching the stern decoration is that the opening was too big too completely cover with the metal badge so I added some inside trim (would be hidden anyways) and once painted with a brass color (different from the white, blue, and red coloration scheme that Mamoli indicated), I glued it down with CA.
  25. mrcc
    Here's the close-up... it is offset ever so slightly to the left but not noticeable on the picture. Also I should have placed the top portion of the rudder a little closer as the pintle was not pushed in far enough onto the keel prior to the CA setting. The most obvious issue though is I sanded back too much into the keel board and into the plywood... Any suggestions in how to fix? Laminate a piece of 0.5 mm walnut strip and then sand back I guess...

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...