Cathead

Started on the masts last week.  I was pretty ignorant to how many parts were involved in building them up, and the Occre instructions are borderline horrible especially regarding the mast tops, I had to watch quite a few videos just to show steps that aren't even in the instruction book.  I'm really starting to understand why people avoid kits that have bad instructions.  Another common complaint I see about this kit is most of the builders seem to run out of 1mm brass rod.  I ran out before I even started on the masts, and the masts require quite a bit of the material for the railings on the tops,  I broke down and just ordered 10 bucks worth of brass rod from amazon and that should last me for many future kits.
 
Lower mainmast and foremasts, Mizzen mast work has just started and was in the garage drying with a fresh coat of shellac.

 
Bowsprit ready for some rigging.

 
I also decided to add a head to the ship with some 2x1 walnut strips, this wasn't part of the kit but I thought the ship looked a little naked with nothing there to fill the void. It's not accurate to plans or anything, and I may add a seat of ease and toilet paper holder in the future. 

 
How the ship is currently looking.

 

With longer days, and warmer weather, progress has slowed down as my focus has shifted a bit to being outdoors more as spring arrives.  I do still work on Cheerful daily though.  I'm working on the chain plates.  As with the backstay plates, I cut strips out of a 6" x 12" brass sheet.  I then cut the 8 chain plates longer than needed.  Next I shaped the tops of all 8.  Being my first ship build, I had to do some research when I got to Chuck's instructions, "Assuming this isn't your first ship model, the angles for each chain plate were found in the usual way."  Glenn (glbarlow) had some good photos in his Cheerful build log that show how to rig a temporary mast to get the desired chain plate angles.  I made a jig to get the rake of the mast correct, when compared to the plans.  Then I secured the mast in place with temporary fore and aft stays.  The simulated shrouds are tied off at the correct height and spacing on the mast.  Knowing the chain plates are not exactly the same length this process was key to do before I cut them to length and drilled the lower 2 holes on each chain plate.  I have the port side chain plates finished more or less (they do still need a little tweaking).  Each one is marked on the back for which position it belongs in.
 
Erik

Well, I've made some progress. Glued lengths of red ribbon onto the roof awning to make the roof alternately red and white stripes. But I don't think I'll do it that way again. I've found my wife's wavy scissors won't cut cloth, only paper, so the 'fringe' won't be able to match the roof. So I'll probably just paint the stripes on instead.
 
Also added the mesh netting at the railing and learnt a few things. Next time I'll add the mesh behind the rail before I put the rail on the model. It'll look better. I did this with the rail on the aft half of the vessel - it looks and works better.

And I'm fixing an edging to the deck to cover the edge of the plywood. I discovered some REALLY thin veneer languishing neglected at the Men's Shed and it's ideal - so I've commandeered it all for myself.


Should do for a large number of future models of this paddlewheeler. And it's OK, because they'll be sold as fundraisers for the Men's Shed and the volunteers who operate her. 
 
Steven

Sails…

Carefully trace all sails from drawings. 

 Cut out sail leaving 1/4” to fold over the edge. I use a muslin material purchased at a fabric store. The Kit supplied sail cloth is usually too heavy. 

Fold the 1/4” edge seam and iron it flat for sewing. 

Trim corner to lay flat before sewing. 

Edge seams sewn 1/8” from the edge. 

Trim the under side, fray check the fabric edges and iron out flat. 

Mark up seams with water soluble ink pen. (fine point) 

Sew seams including those for reef points. 

Main Sail sewn and ready for additional details.  Bolt rope, reef point ropes and corner rings. 

Remaining sails cut out ready for sewing. 

Fore Sail 

Stay Sail
Main Top Sail

Fore Top Sail

Jumbo Jib

Jib Sail

Balloon Jib

All Sails sewn and ready for details to be added. 
 
Cheers 🍻 

Hello,
the carpenters finished the great cabin for the captain. It took some time, because the oil has to dry, some days of because of eastern and the good weather we had. But now it is raining again, so we are busy at the yard.




Here the carpenters have the first bulwark allready finished in the raw.

Thanks, Dick. I had been puzzling over this very issue and hadn't come up with a workable solution - apart from perhaps having the ladder going off to the side! (Perhaps great minds think alike.)
 
Certainly, the contemporary pictures are quite equivocal - they could be interpreted as having the ladders either behind or to the side of the mast - except that some show two ladders, one on each side of the mast, each leading down to the relevant gunwale. I don't know if I'm prepared to do two for each mast - I'm still thinking about it.
 
As far as what the rungs should be made of, I know you used wood, and that would probably be easier to make than rope ones, but I'm still not certain which way I'm going to go.
 
Steven

Just a couple of points about Jacob's ladders in latin ships. Make sure the ladder doesnt foul the yard or its tackle on going about. On my round ship I positioned the rope ladder (with rope rungs) side on to the mast. Anyone who has seen circus performers use a rope ladder knows that they clamber up the side of the ladder. This minimises "bellying out" of the ladder which would be worse if the ladder were climbed face on.


Cheers
Dick

I've been doing test runs with the silkspan, gluing it together with the matt acrylic varnish that was recommended. Not too bad. And trying out for painting the crosses on the sails. I've tried various ways of doing it, but still not really happy with the results. From the left - acrylic painted directly onto the sail, a band of different acrylic, painted onto the sail and then outlined in pencil, painted onto a separate piece of silkspan and glued onto the sail. This seems to be the least worst version.

Heart in mouth, I've started gluing the reinforcing strips to the edges of the sails.There's a bit of transparency to start with due to the varnish, but if the test piece is to be relied upon, that seems to fade after awhile as the varnish matures.


But maybe I should have made the sails a bit bigger and folded the edges over, rather than glue on separate strips. I think it would have been easier.
 
I'm also researching rope ladders for the masts. I'd hoped to avoid them, as they often don't appear in contemporary pictures and several pictures show crewmen shinnying up shrouds, not using ladders. Unfortunately, a Genoese round ship from a few short decades different has an undeniable rope ladder, though the top end isn't in the picture.

So I've been checking out other rope ladders - I have two questions: 1. Where is the top of the ladder fixed to and 2. Are the rungs rope or wood? Here are the pics I've been able to find that are vaguely similar in time period (by "similar" I mean no more than two or three centuries apart!).
  
14th century Chest of St Simeon, Croatia                                                           1360ish St Ursula by Paolo Veneziano
   
1422 from  north doors of the Florence Baptistery by Lorenzo Ghiberti                    1430 approx. St Augustine Departing from Africa by Master of Osservanza
   
Boccaccio by the Maitre des Cleres Femmes du duc de Berry, 1403                                  British Museum Egerton 943  f. 63  Dante embarks on a ship 1st half 14th century
   
Dante on shipboard. Date unknown, but looks 14th century                 Siege of Damietta - frescoes in Palazzo Comunale, Mantua,(1220-1230)
   
From church of San Eustorgio Milan 1336 to 1339                                        Unknown ship - maybe 13th century
 
                                                     
Detail from Icon of Virgin and Child, Church of St Kassianos,                         Martyrdom of St Ursula from the Belles Heures du Duc de Berry                                   
Nicosia, end of 13th century                                                                            1405-9 Met Museum BH Lg19v 178v   
 
Surprisingly, most of them seem to come only up to the bottom of the "crows nest" (I couldn't call it a top - too confusing) or even lower, leaving the sailors to clamber up over the sides of the thing to get in - unless there's a lubber hole in the floor of the top, but they seem too small to allow for that.                                                      
 
Steven

This stage of the build is hard as you do a lot but there is not a lot to show as finished. The more of the rigging you can do off the model the easier it will be and better it will look. It is just hard to resist putting it on the model so you can see progress.
 
Good work.

I have been making progress on many fronts but nothing completed yet. I wanted to provide a status of the build up to this point though.
 
First the sails. I am in the process of adding the bolt rope to the fore and main courses, after adding the reinforcement pieces. I have been progressing from loop to loop on each sail so I can do about three loops a day because of the time for the matte medium to dry. Once the bolt rope is done I will be making the holes along the top of the sails and in the thin reinforcement strip for the reefing points.
 

 
I have finished painting the 3D printed cutter. I used a bright white paint for the outside of the hull but gave it a wash of diluted unbleached white paint as a final coat. I painted the rub rail and the hull up to the gunwales black. I have started adding the interior wood pieces so I should have that finished up soon and lash it to the deck.
 

 
The rest of the activity has been focused the bowsprit, masts, and booms, I have the sections made and finished, so I am adding the details and stropping and adding the blocks and deadeyes.
 
Bowsprit:

 
Booms:

 
Main mast:

 
Fore mast:

 
Hopefully I'll have some completed items to report on soon.

Very nice progress Eric! I agree with Keith and John, she is truly beginning to look like the photos of her and your work on the canvas looks great. As for your paddlewheel, that is one of my favorite parts to build. Just the details that go into them add to the beauty of these boats. 
 
-Brian 

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!

Time for a big dump of progress photos!
 
I completely failed to take photos of building the roof for the pilot house and cabin, but it wasn't complicated. I just cut a thin sheet of wood to the shape I wanted, spread glue on the "rafters", and secured everything with rubber bands.
 
The photo story picks up again as I applied the simulated canvas. I used the same method as I did on Arabia: strips of masking tape held down with a thin layer of wood glue. When that's dried overnight, I trim the edges and paint it. It's held up perfectly on that last model, I really like the texture, and it's more forgiving to work with than tissue paper or silkspan or other options. Plus it's dirt cheap. Here's a sequence showing the progression of slightly overlapping layers on the gently arching cabin roof:



And the same for the pilot house:
 


I'll use some pastels to weather this a little, dull it down, and give it some subtle variation in tone.
 
In the meantime I worked on laying out the support posts for the hog chains, which needed to be carefully situated to run just along the outside edge of the cabin roof. So I marked the final location of the cabin and carefully laid out where I wanted the posts to go through the boiler deck. Then I drilled a series of small holes and used a sharp knife tip and then small files to make the final shape:
 

I then made a simple jig for the angle I wanted the posts to sit at, and used this to set them up. Here they've already been cut and painted. The black tips are meant to represent the iron caps that actually held the hog chains onto the wooden posts.

And here are a few shots of the fore and aft hog chain posts resting in place (not yet glued); you'll notice I temporarily removed the chimneys to avoid any possible damage as I worked on all this:
 



I also built the assembly that goes over the stern, which I'd left off until now since it rises above the boiler deck and I didn't want to bump or snap it while doing earlier work on the deck.
 


Finally it was time to start attaching things for good. Here I've glued down the cabin and pilot house (big step!):
 

And while that was drying I got started laying down the "canvas" on the boiler deck, working up to the aft part of the cabin. I'll let this all dry completely before proceeding up either side of the cabin.
 

A close look will also show that I built and attached the little L-shaped guard wall around the staircase up to the boiler deck.
 
Once all the boiler deck canvas is laid, I'll (re)cut the hog chain post holes, paint it carefully (trying to avoid the cabin walls), then attach the stern piece. At that point the model will really be coming together though a lot of detail work remains to be done (not to mention the paddle wheel, which I'm dreading).
 
Thanks for reading (or at least skimming) through that big dump of updates!