Chuck

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

Nicely done, Chuck.

That tuck frame is a really cool detail.  The red counter is a great example of how colorful ships could be in period.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

The Square tuck....Thank goodness this isnt a real POF project.  Here is the simplified version.
 
The photo below shows the first beam added which to create teh base for the stern post.  It runs down the center of the square tuck so I can glue the stern post on later.  It is 1/8" thick and 7/32" wide.  The same width as the stern post
 
The same photo below shows the second timber....how I took a wider piece that was 1/8" thick.  I shaped it so the seam between the lower counter and this timber was very tight.   Then I measured and marked it so it would be 1/8" wide as well.  This will of course be repeated on the other side once it is planked.
 

 
The finished timber below.
 

 
Then it was time to create the side piece which will finish the square tuck frame....this was the hardest piece but not that difficult at all.   I just took a larger 1/8" thick piece of boxwood and shaped it to fit tightly against the two timbers I just just completed.  I tried to get real tight seams. At the same time,  it hangs off the side of the hull.  Then I traced the shape of the hull against the back of this piece.
 

 
Heres what the tracing looks like.  The piece was cut to shape on the scroll saw.
 

 
Then,  this piece was temporarily glued back in position with just a small dot of CA.   This was done because it will need to be removed after it is faired with the hull planking.  See below.  And as done before,  I drew another line to establish a 1/8" wide finished timber.  This was cut out and glued into position finishing the frame for the square tuck on this side of the hull.
 

 
Here is what it looks like.
 

 

 
Finally....it was planked inside with vertical planks the same width as the hull planking.  Tarred seams were simulated.   I was very careful to get very tight seams.   In actual practice these planks would be normal thickness and the ends resting in a rabbet along the edges of the square tuck frame.
 
In my case though,  I just faked it using planking that was actually 1/8" thick which is the same thickness as the frame.   It all worked out in the end.  I am quite pleased with the results as this is normally a really tough detail to model convincingly.   Now to touch up the red paint on the counter or maybe its just best to wait till the planking is all done.
 

 

 

 
I can now start planking the last belt  on the starboard side.

wonderful work Chuck !
 
Nils

Beautiful craftsmanship Chuck! Hope you and yours have a great Holiday Season! 
 
Cheers