Dan Vadas

Thank you all for the Likes and comments. These are one thing that is keeping me going with this build - another is that I'm thoroughly enjoying it  .
 
The two compressed air tanks. The ends are slightly domed. I cut some scrap paper roughly to shape to prevent any crushing later. The skin is only glued along it's edge :



I've fitted all the main wheels and finished the brake mechanism for them. The brake shoes needed a little sanding to bed them in properly :



To hold the wheels into the tube axles I mushroomed the ends of some tight fitting styrene rod with a small soldering iron and filed them as flat as possible :


The drive axle needs to be a solid fit as the two wheels have to turn in synchronisation. The crank pins are offset by 90 degrees from each other so that one wheel is vertical while the other is horizontal. This keeps the drive going without any stopping. To make sure they don't slip on the axle I made a keyway for each and also used CA glue to hold them to the axle :


Danny

!WOW!  awesome job Danny....look'in great  

Well, you can "fire" it up, but just once!

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

OK Phil, let's try these for starters
 
1. I'm assuming you're using an acid-free PVA white glue, aka Craft Glue. Use a nice thick one - the more water content the glue has the more warping you will get.
 
2. Use as little glue as possible to still get a good bond. Too much glue will ...... you get the picture  .
 
3. Use an appropriate applicator. I usually use a squeeze bottle - one with a 2mm tip for large parts like bulkheads or decks, and a much smaller 0.6mm needle-tip one for smaller parts. You could also use a paintbrush for large areas - put the glue into a small container like a plastic medicine cup or similar item and brush it on.
 
4. Work quickly. You don't need to cover the entire area with glue, small areas without glue won't matter, but you need to get the pieces together before the glue dries too much. If it does, apply another thin layer over it.
 
5. On very large things like decks - don't attempt to do too much at once. You may need to do it in two or more sections. I usually align it all and tape down the "finish" end to my work surface. Then I tape a couple of "stops" to each side and the end of the surface so it is easily re-aligned accurately later. Now I run a bead of glue down the "start" end while keeping the "finish" end aligned in the stops, press it down and let it dry enough so it won't shift. Now lift the "finish" end and start applying glue at the "start" end, pressing it down with a flat piece of wood about 20mm behind the glue as you go. When it's all done press the entire deck down with your flat timber and - this is important - bend the piece gently (ends down, middle up) to "pre-stress" the part. Now slip it under a sheet of glass on a flat surface and let it dry THOROUGHLY (over-night).
 
I hope this helps a bit. The main point is - don't use too much glue.
 
Cheers, Danny

I'll post an answer to that in my next one later today Phil, I'm in a bit of a hurry at the moment and wanted to show an update on my loco.
 
Here's where I'm up to at the moment, details of how I got there will follow a bit later :





Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Put an electric motor in it and watch the mechanism go through the motions. I realize you can't "fire" it up.  Great build, Danny.

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

I'll post an answer to that in my next one later today Phil, I'm in a bit of a hurry at the moment and wanted to show an update on my loco.
 
Here's where I'm up to at the moment, details of how I got there will follow a bit later :





Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Ken - fire up a paper model ????? I don't think that will end well  .
 
I'm going backwards in the following posts to show some of the construction involved in the earlier post of my progress.
 
Quite a bit of work in building the two steam cylinders. I had a few re-does with these, as I didn't understand the basic principles of how they actually worked. Thanks to a couple of other build logs, Stephan and Lothar on German Paper Modelling sites, I eventually got them together the right way up and also WORKING  . In these next pics I've cut apart one of my early failures. I actually managed to save every part and rebuilt the little section :

The shaft should have gone right through the piece. I had added a paper roll to glue the legs to - wrong :

Sometimes a single-edged razor blade works better than a scalpel for cutting parts off as it's about half the thickness :


Some of the parts for the end plates etc :

How I keep multiple pieces aligned on an otherwise difficult part :


These two little pieces were very difficult to roll due to the cutouts in the middle. They turned out quite well  :


Some finished sub-sections :


Lots of laser-cut bolt heads and how I cut them off the sheet :

These name plaques turned out really well. They are laser-engraved, the gold colour was applied with a Pitt Pen :

The finished cylinders. I'll put the name plaques on near the end of the build :

Danny

Thank you, Danny.  
 
I bought the Mont Marte glue that you recommended a while back.
 
I’ll give it a go with the Big Fitz and let you know how it goes.
 
Moab, thanks for the heads up.

I'll post an answer to that in my next one later today Phil, I'm in a bit of a hurry at the moment and wanted to show an update on my loco.
 
Here's where I'm up to at the moment, details of how I got there will follow a bit later :





Danny

OK Phil, let's try these for starters
 
1. I'm assuming you're using an acid-free PVA white glue, aka Craft Glue. Use a nice thick one - the more water content the glue has the more warping you will get.
 
2. Use as little glue as possible to still get a good bond. Too much glue will ...... you get the picture  .
 
3. Use an appropriate applicator. I usually use a squeeze bottle - one with a 2mm tip for large parts like bulkheads or decks, and a much smaller 0.6mm needle-tip one for smaller parts. You could also use a paintbrush for large areas - put the glue into a small container like a plastic medicine cup or similar item and brush it on.
 
4. Work quickly. You don't need to cover the entire area with glue, small areas without glue won't matter, but you need to get the pieces together before the glue dries too much. If it does, apply another thin layer over it.
 
5. On very large things like decks - don't attempt to do too much at once. You may need to do it in two or more sections. I usually align it all and tape down the "finish" end to my work surface. Then I tape a couple of "stops" to each side and the end of the surface so it is easily re-aligned accurately later. Now I run a bead of glue down the "start" end while keeping the "finish" end aligned in the stops, press it down and let it dry enough so it won't shift. Now lift the "finish" end and start applying glue at the "start" end, pressing it down with a flat piece of wood about 20mm behind the glue as you go. When it's all done press the entire deck down with your flat timber and - this is important - bend the piece gently (ends down, middle up) to "pre-stress" the part. Now slip it under a sheet of glass on a flat surface and let it dry THOROUGHLY (over-night).
 
I hope this helps a bit. The main point is - don't use too much glue.
 
Cheers, Danny

OK Phil, let's try these for starters
 
1. I'm assuming you're using an acid-free PVA white glue, aka Craft Glue. Use a nice thick one - the more water content the glue has the more warping you will get.
 
2. Use as little glue as possible to still get a good bond. Too much glue will ...... you get the picture  .
 
3. Use an appropriate applicator. I usually use a squeeze bottle - one with a 2mm tip for large parts like bulkheads or decks, and a much smaller 0.6mm needle-tip one for smaller parts. You could also use a paintbrush for large areas - put the glue into a small container like a plastic medicine cup or similar item and brush it on.
 
4. Work quickly. You don't need to cover the entire area with glue, small areas without glue won't matter, but you need to get the pieces together before the glue dries too much. If it does, apply another thin layer over it.
 
5. On very large things like decks - don't attempt to do too much at once. You may need to do it in two or more sections. I usually align it all and tape down the "finish" end to my work surface. Then I tape a couple of "stops" to each side and the end of the surface so it is easily re-aligned accurately later. Now I run a bead of glue down the "start" end while keeping the "finish" end aligned in the stops, press it down and let it dry enough so it won't shift. Now lift the "finish" end and start applying glue at the "start" end, pressing it down with a flat piece of wood about 20mm behind the glue as you go. When it's all done press the entire deck down with your flat timber and - this is important - bend the piece gently (ends down, middle up) to "pre-stress" the part. Now slip it under a sheet of glass on a flat surface and let it dry THOROUGHLY (over-night).
 
I hope this helps a bit. The main point is - don't use too much glue.
 
Cheers, Danny

Amazing!!!!...Moab