Beef Wellington

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

It must be very satisfying putting all of this together, they fit so well!  🙂  Love the approach, wish I could emulate!

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

OC, Carl, Rob, Thomas, Mike, Dave, Pat and all the likes...definitely helps keeping one moving forward!
 
Finally, have all the guns in position an the breeching ropes in place.  Amazingly time consuming, no more need be said, and glad its behind me.  I did allow myself the small concession of using a ringbolt for the less visible guns, and went with a ringbolt and ring for those visible in the waist area.  Despite the latter being more 'correct', the jury is still out on whether the results totally warrant it at this scale as the eyebolts only version seems acceptable to my eye (comparison photo below).   As usual, dilute PVA was used to help keep the breech ropes in position and to try give them a sense of weight.  Photos seem to call attention to all the little dings and dents that seem unavoidable and thankfully not really noticeable during normal viewing.
 
A very simple jig was used to help keep lengths consistent.  When using rings, I found that opening up a ringbolt using a small metal point and reclosing was easier, faster and predictable than opening up the ring itself.
 

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Thanks everyone for continued interest, kind comments.and likes...
 
Block Stropping:
I've started stropping blocks for the hauling tackles.  I'm opting for a double-single block combination, although I've read that doubles were only used on 32lb'ers.  What I think this really means is that the tackle consisted of 2 double blocks.  For a mid-range 18lb'er, a double-single seems appropriate and makes engineering sense.
 
This seems yet another painfully slow repetitive process!  With this progressing in the background, will be intersperse with other sundry items.  Whilst not too difficult once the approach has been proven, clumsiness never quite seems to diminish.  Overall, happy with the way these turned out which is really testament to the fantastic blocks that Syren produces.  The picture below is the result of 3 solid evenings work....sufficient for the waist guns.
Hooks were threaded with 0.3mm Syren line, and secured using 4 alternating overhand loops using tan Uni-thread (barely visible given its so close in color, but is what was also used for the breech rope seizing).  For the 1/8" double block, the strop was twisted through 90 degrees while securing to ensure the appropriate alignment with the block. GS-Hypo was applied and left to dry before trimming off excess Uni-thread Line held in position around the block and then secured with a simple overhand loop Dilute PVA applied to the overhand loop and the stropping around the block.  Was very liberal with this as it is not visible when dry, and anything that provides additional security seems silly to ignore. Trim excess stropping line once PVA has dried
 
Waist Beams:
First off, a correction needed to be made to the interior bulkhead to correct the position of the beam at the front of the main mast.  The position of these had been taken literally from the plans very early in the build and it was clear that they are not in the appropriate position relative to the mainmast.
 
Secondly, needed to finally decide how to deal with the supplied walnut beams.  These have a pretty rough grain and require a lot of cleanup to get nice smooth curves after removing from the sheet.  Following the scheme shown on the contemporary models (painted red with upper natural face of boxwood), thin strips of overwide boxwood strips were liberally glued to the top of the beam,  gradually sanded back and painted when flush.  The lamination is virtually undetectable, and it also helps ensure the walnut grain is minimised.  Filler can be used in any stubborn imperfections.  Although a bit of a cheat, I just couldn't face cutting my own from box, and quite honestly, I doubt I could get satisfactory results with tools at my disposal.
 

 
Sub-Deck alterations:
Increasing the thickness of the beams also has the benefit that the top of the beams are flush with the sub-deck.  Hoping this means that the gang boards can now be planked with the sub-deck providing a solid base, but remaining invisible from normal viewing angles.  Slots were cut into the sub-deck to accommodate the laminated top surface.  Picture hopefully self explanatory.
 
In position, the next required adjustment is revealed.  The waist opening in the sub-deck has perfectly parallel sides.  After studying various deck plans, it appears more appropriate for the gangboards to follow the line of hull (i.e. planks are constant width throughout their length).  The approximate width of the gang boards were estimated from the AOTS plans and transferred to the deck.  The hashed area indicates what will need to be remove.  In actuality, more will be removed to set it back from the actual edge of the planking proper.
 
Back to stropping more blocks....
 

Slow but steady progress on planking. 
At first, I was in doubt and fear about how to carry out this process, but I must say that I enjoy it very much .

Wonderful work, Jason! And your attention to detail is amazing. It is a rare treat to see this kind of detail on the trunnion mountings!
 
Thomas

Stunning work Jason!
I really like your attention to details. Not to mention how good she looks fully armed !

Excellent work Jason!

That is seriously nice work Jason; she is looking good with her 'teeth' added.
 
cheers
 
Pat

Very nice work on those guns Jason, I got off lightly having only a dozen on my little Cutter.
Love the natural drape you’ve achieved on the breeching ropes , and impressed that you went with the proper hitch for the ring bolt seizing.
 
Your little jig for rope length will prove useful for me in the very near future.
 
B.E.

OC, Carl, Rob, Thomas, Mike, Dave, Pat and all the likes...definitely helps keeping one moving forward!
 
Finally, have all the guns in position an the breeching ropes in place.  Amazingly time consuming, no more need be said, and glad its behind me.  I did allow myself the small concession of using a ringbolt for the less visible guns, and went with a ringbolt and ring for those visible in the waist area.  Despite the latter being more 'correct', the jury is still out on whether the results totally warrant it at this scale as the eyebolts only version seems acceptable to my eye (comparison photo below).   As usual, dilute PVA was used to help keep the breech ropes in position and to try give them a sense of weight.  Photos seem to call attention to all the little dings and dents that seem unavoidable and thankfully not really noticeable during normal viewing.
 
A very simple jig was used to help keep lengths consistent.  When using rings, I found that opening up a ringbolt using a small metal point and reclosing was easier, faster and predictable than opening up the ring itself.
 

I think you're right Dowmer, having pre-made the hatch surrounds to the plans as I thought,  I obviously didn't take the round down sufficiently to the deck level, and then forgot all about it as I moved onto other stuff.
 
Thanks for the heads up, we need more members to point things out that puzzle them or don't seem right to help keep us on track.
 
B.E.

B.E.
 
I have a question that has been nagging at me.  In one of your previous pictures of your hatch coamings it shows the edge square with the top rounded off.
 

 
I always thought the edges were rounded down to the deck to prevent nasty ankle injuries etc.  Here’s a picture of what I mean.
 

 
 
Are there other ways to model them?  
I’m certainly no expert, and I don’t mean to be critical, but I’m always looking for accurate or contemporary ways of construction.
 
Thanks