Beef Wellington

Beautiful work Simon, fantastic work with the CNC machine, I have no idea how you do it but the results speak for themselves.  Just amazing, well done indeed!

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Happy Thanksgiving to all of those in the US!  Unfortunately the  shipyard has had to suddenly close due to a minor, but messy, health and safety violation involving a clumsy thumb and Xacto knife - nothing serious but plasters/band-aids preventing fine work.
 
Good opportunity to sit back and ponder gun rigging as I'll need to order additional materials from Syren.  Think I'm done with additional detailing on the cannons in the interests of sanity;
Monograms are from Syren, given a quick dash of 'dark iron' Cpaint and glued into place with CA Cap-square eyebolt made with wire and the cap square joint bolt is one of the smaller PE ring bolts.  
 
First mock up of potential rigging, as previously discussed, the breech rope is 0.88mm Syren line.  This line does make the half hitch a little more cumbersome, but think it can still work, even though they will be somewhat hidden even for most visible guns in the waist.  Going to live without the wheel lynch pin and cap square pin/chain.
 
Cannon rigging:
Breeching rope does require some dilute PVA to hold into position on the button.  Wanted to give the hauling tackle a feeling of 'weight', and have been experimenting assembling these off the model using a serving machine to get consistent spacing and also do the frapping.  Procedure still to be finalised…
 
Details as follows:
Block are 1/8" (3.18mm) single/double blocks from Syren Blocks are stropped with 0.012"(0.3mm) line Port tackle line is 0.008" (0.2mm) line Hooks are 4mm from Syren (these are black plastic which I ordered some time ago and don't think Chuck still offers them which is a shame as they seem easy to work with)

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Lots of good discussion regarding colours!   I seem to be in a minority not finding the 'new' colour to be anathema and the basis for determining it entirely reasonable.  I wonder what 'evidence' there is/was for the prior colour… other than years of public display of a colour that was itself possibly just speculation.  I would love to be in the alternate universe where the current/past colours are reversed - probably exactly the same arguments 🙂

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Lots of good discussion regarding colours!   I seem to be in a minority not finding the 'new' colour to be anathema and the basis for determining it entirely reasonable.  I wonder what 'evidence' there is/was for the prior colour… other than years of public display of a colour that was itself possibly just speculation.  I would love to be in the alternate universe where the current/past colours are reversed - probably exactly the same arguments 🙂

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Lots of good discussion regarding colours!   I seem to be in a minority not finding the 'new' colour to be anathema and the basis for determining it entirely reasonable.  I wonder what 'evidence' there is/was for the prior colour… other than years of public display of a colour that was itself possibly just speculation.  I would love to be in the alternate universe where the current/past colours are reversed - probably exactly the same arguments 🙂

Before I go too much further I want to get the guns mounted on the upper deck and rigged. That means getting all the aiming and running in / out ropes ready. I ordered 110 boxwood 3mm blocks from cornwall model boats and some extra 0.1mm natural thread. The plan is as follows (excuse my drawing)
 
Rig three of the following with two single blocks. One will go on each side, with the falls nearest to the bulkhead. One will go at the rear of the gun for pulling away from the bulkhead to reload... the fall will be nearest the gun on this one. The ropes in use are 0.5mm for the main rope, and 0.1mm for stropping(?) the block. I'm using 2mm hooks at either end (available separately from caldercraft through CMB)... These have been blackened with brass blackener, making the whole thing much easier, as the holes don't have to be opened up again as they would with painted hooks. Superglue is used on the end of the rope to help get it through the hooks / blocks as necessary. The 21cm at the bottom is the scale length of the rope, however in practice I'm making these shorter, as the plan is to put cheese at the end of each rope.  I've put a photo of these in construction at the bottom too... I can't remember who suggested making these by putting them onto the stick side of masking tape, but it's genius! Thanks to you!
 


 
I realise I haven't mentioned the breach rope... I'm using some rope I had left over from Royal Yacht Caroline, which looks really nice... I think it's about .75mm, and a nice light grey colour. It's untwisted in the centre and the loop placed over the cascabel.
 
So... 11 side tackles done... I'll be fully rigging all the visible guns but not the rest... They'll have breaching ropes, but not side tackles. (That is, unless I change my mind, which may well happen... we'll see.
 
Once the guns are in place, I'll finally install the gratings, pillars, chain pumps, hand pumps, bitts, manger, elm-tree pumps, and gun shot racks... I also need to remember to put the cleats in... Once that's done, we'll really be making some good progress, and it'll be onto the head rails. At least, that's the plan. Should keep me going for a while!
 
Still loving this build. It's by far the most complicated I've ever attempted, but it rewards patience, and nothing's so hard it can't be done with forethought and planning. (oh yes, and you lovely ladies and gents on modelshipworld to give inspiration and encouragement!)
 
Anyway - happy building
 
Rob

Happy Christmas to you all
 
I've had a wonderful Christmas so far, and it's included some time to work on Ethalion.
 
I've completed the rigging of guns 3-9 on the starboard side, and started guns 3-9 on the port. Eventually I remembered that double-sided tape was far better than masking tape wrapped round for making the coils of rope. The extra stickiness made life much easier.
 


 
I've also finished making up the shot racks that surround the gratings on the upper deck. A simple jig was made to align the drilled holes.
 

 

 
Anyway - back to making training tackles... (12 pairs of blocks still to rig!)
 

 
Happy building
 
Rob

Happy new year! Hope everyone's having a great start to 2019.
 
Gun rigging is continuing apace... Not much difference to show in photos, as I've mainly been rigging blocks and making up training tackles.
 
To add a little variety, I started working on the beams that will cross the gap between the walkways. These are provided in the kit as six beams in walnut. (part 44)... having done so much of the build with Walnut, I wanted to keep with that option. I considered trying to bend the box, but I was concerned that it would quickly spring back. Instead, I decided to shape them from 6mmx2mm stock.
 
The box strip was laminated to make up the 4mm width, and then the walnut part used as a template.

Parts sat roughly in place...

Lots of good discussion regarding colours!   I seem to be in a minority not finding the 'new' colour to be anathema and the basis for determining it entirely reasonable.  I wonder what 'evidence' there is/was for the prior colour… other than years of public display of a colour that was itself possibly just speculation.  I would love to be in the alternate universe where the current/past colours are reversed - probably exactly the same arguments 🙂

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Happy New year to everyone!  First off my apologies for not being on the site as much as usual and checking in on everyone's progress, something I hope to rectify soon. 
 
My progress has been limited, some small steps have been taken, and problems encountered that stopped me in my tracks for a while.
 
Channel Brackets:
The kit supplies PE channel support brackets, unfortunately I found this unworkable as is as the profile impinged on the decorative molding, they're also a little wider than indicated on the plan.  The PE parts are scored pretty heavily at the bending points so trying to tweak these was not really an option.  The problem also identified by others is that there are not enough provided in the kit (per the AOTS there are 3 shown on the mizzen, 6 for main and 4 for the fore channel) and only 11 provided, so the kit is 2 short.  Further analysis suggests its likely 3 short as there are 2 brackets used between ports, and it appears that one is simply hidden behind the stock of the anchor on page 69.  I'm going to reflect 5 brackets on the fore channel.  Another slight complication is that the mizzen brackets need to be smaller to account for the lower position of the channel in the open rail configuration I'm following.  Basically I needed to make my own, and without any really good photos to follow went with my gut.
 

 
Not having any other suitable materials handy, my eye turned to one of the spare sets of PE from other CC kits I had purchased a while back.  Not sure which kit, but a little filing and cutting to length allowed the chains to be workable.  These also appear to be almost exactly the same narrower width as shown in the AOTS profiles.  The center portion of the Diana PE part was re-purposed to attach to the channel.  Exactly the same approach was taken for the mizzen, except that the top of the Diana PE part was used and different dimensions for the bracket supporter.  This was all rather fiddly and took rather longer than I'd care to admit... 🙂
 

 

 
Cannons....finally:
Once the channel supporters were in place I could then proceed with installation of the cannons.  These are now glued in place (using CA), I didn't pin these in place as this would have been a little problematic at this stage, and they seem quite secure as is.  Breeching ropes were attached off the ship prior to installation.  Another self imposed delay was decision to go with 'light brown' Syren line rather than the 'tan' used previously - this seems to have a tone that blends better with the colour palette.  The Syren line is very nice to work with and the usual trick of using dilute PVA was used to fine tune the final profile.  For these more obscured cannons, I used a simple eyebolt to secure the breach rope, for the more visible ones in the waist, I want to explore using ringbolt as per practice, but even using a simple eyebolt gives a satisfactory result to my eye at this scale.
 

 
And finally, the exterior shot...in retrospect I'm happy with the decision to install the channels and brackets first as I'm pretty sure there would have been collateral damage to cannons during installation.  5 down, 23 to go.

Tumbe-home bulwark.
 

Thank you all for your feedback.  
 
I continue to build a model. Mast

I have started to work on rudder.
Hinges are made from 0.3mm brass sheet, 0.9/0.7mm Albion Alloys tube and 0.6mm wire.

Work continues on stern decoration. CNC machining could be very frustrating.
I have great difficulties with machining, due to unexpected movement of tool into the part (-Z axis). Full inspection of machine was needed incl. mechanical and electrical parts. Also programming was changed and I finally (after two weeks of work and several destroyed parts/ tools) managed to get undamaged part. 
Windows were also made from 0,3mm transparent plastic sheet.

Small update, working on windows and stern decoration. All from boxwood.

Hello everyone,
 
it has been long since the last update. I make some progress on Mercury, but my build speed is very very slow due to disability caused by illness.
 
I managed to finish wales and started with stern. I really like to work with ebony wood, but is very difficult to process.