Jump to content

SS Warkworth 1875 by Moony - 1/48 - PoB - early Steam Collier built in iron


Recommended Posts

Hello wood-, iron- and steelworms!

 

post-23296-0-03261400-1453151688.jpg

 

The very first thing I've to admit is the scale is nominally 1/36 - but due to an enlargment fault it is only 1/40. So I said to myself "Damed 4 dots beside the lne... it could have been the drying of the paper or the wrapage in the big copy machine... so I decided to take the plans as they are - and do the start with them.

 

post-23296-0-67758600-1453151668.jpg

 

I've got a thread about the plans here: http://modelshipworld.com/index.php/topic/12596-ss-warkworth-an-early-steamer-not-too-big-please/ andall the planing facts will be placed there.

 

post-23296-0-47716100-1453405820.jpg

 

The S/S Warkworth was built in 1874 in Newcastel up on Tyne on the shipyard of C.S.Swan & Co, out of iron. I'didn't find a prpper date of launch only this date on the (usualy coloured) sideview of S/S Warkworth. This can mean she was launched on the 8th II. 1875 or the drawing is dated to this day. Does anybody know something about dating traditions in the shipyards on Tyne? 

 

The ship was ordered by H.Andrews who was connected with Broomhill Coal Co. for the coal transport and built in a progressiv design. It is now known that if the angle of the water flowing to the line of the keel after is exceeding about 18°, the flow of water toward the propeller is liable to be turbulent in creasing drag. Due to this the lines were altered compared to former designs.

She has got a complete forecastledeck - til the bridge the deck is iron not any longer wooden. To store the new cylindrical Scotch boilers the deck of the  boilerroom had to be raisen - the enginerooms hight had to be extended too - due to standing hammer steammachine with a high and low pressure cylider. This kind of construction was basically used for the next three quarters of a century - till the steam coasters started to disappeare in the mid 1950s.  

 

The captain was no longer near the rudder as used fore the last 3000 years - hhis place went to a flying bridge infront of the funnel - raised on a little platform called "Flying Bride". To seperate it from the "real" bridge connecting the two side wheel boxex earlier. This interestin light construction gave a good overview to the Officer giving orders to the helmsman behind and below of him at the main steering wheel.

 

S/S Warkworth was built to transport coal - so she had two big cargo spaces of 14,15o and 13,ooo cubicfeet - for ther own coal consumption she had a 102 ts coal bunker.

 

She works in coal trffic on the north-east coast of  Great Britain and measured imperial. and registerd with: 160.8 x 27.1 x 12.9 - at 555 grosstons and 334 nettotons. driven by a 70 hp machine on a single propeller.

 

All the data are from Charles V. Waine's books

 

Steam Coaster and Short Sea Traders (2nd Edition 1980)

The Collier Fleets (1st Edition 1990) 

 

As you can see from the pictures there are not too much details that overcome to us. I couldnt find anything about the propeller - with out the fact that it was  a single one... but does he have five, four or three blades? 

 

So I'll start with the building board and the backbone next week. The construction of the bulkheads will be shown in the article about scetches, plans and drawings. As all the pre-work is done there and the  "output" is shown here to you.

 

The real building progress will be shown here - to give you an Idea of the size I built a little figure for you - standing on a €-cent coin and based on a square-inch he is to scale: MrSquare-Inch

 

EDIT 12/Feb/2016:

Due to my flat's groundplan I've to reduce the scale down to 1/4'' to the foot - 1:48...

 

Hope you like him. 

post-23296-0-67888100-1453512659_thumb.jpg

post-23296-0-49738800-1453513799_thumb.jpg

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Hello friends of the S/S Warkworth,

 

now I made my way back from the DIYshop... everything wraped in dustbinliner to protect the plain wood from the ugly snowraining weather outside. 

 

I bought a

 

2000  * 200 * 28 mm plain board as yard board from pline.

 

300 * 250 mm and 10'' * 8'' plywood boards beechen.

 

250 * 600 mm and 200 * 600 mm for the centrl board plywood pine.

 

Now I can start to put mindcraft ine the cuts that'll be done. 

I decided to use two seperate parts for the midships board  due to the fact that the longer plywood boards looked like the waves of the Sea of Galilee. 

 

Now I'm able to start...

post-23296-0-15147700-1453561589_thumb.jpg

post-23296-0-48319100-1453561592_thumb.jpg

post-23296-0-11613500-1453563378_thumb.jpg

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Moony, this looks like an interesting build. It will certainly be a large model.

Ian M.

 

Current build: HMS Unicorn  (1748) - Corel Kit

 

Advice from my Grandfather to me. The only people who don't make mistakes are those who stand back and watch. The trick is not to repeat the error. 

Link to comment
Share on other sites

Hy Ian,

 

 

she is an intresting ship - I'll have to reconstruct a plenty of details still not in the plan at the monemt. 

Oy yes - she'll be a bit about 1600mm long - she is  a tall lady  ;)

 

Here the Centerline

 

the Mainfames placement

 

and todays pi**-take... you pay for 200 mm and what you get is 195 :angry:

 

Next station:

 

a)

cutting out the bulkhead copies.

 

B)

Transfer the bulkheadlines faced to the mainframe with a pairr of compasses.

 

 

post-23296-0-47029200-1453576794_thumb.jpg

post-23296-0-11084800-1453576803_thumb.jpg

post-23296-0-02186500-1453576808_thumb.jpg

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Yes the is starting to beat with her wings... what I hope is that the model will assemble from the parts as logical as it looks like everywhere here. The ship is the resultant of the parts I put together... but not Tamiya is responsible for the fitting of the parts - it's me!. The challange is to get them so fine and realistic as possibe. The close "affinity" of the scales 1/40 (or 1:39,78 to be Pooterish) makes it possible to use some of the 1/35 items like the tiny Meng or CMK screwsets. 

 

   ... but with a plenty of unanswered questions... 

 

For example the pre-Pimsoll Load Line Mark is with an L and R letter but before 1876 there is a diamond not a circle.

The measurement of the iron-ship loading lines is a complete terra incognita for me - so I'll try not to mess around with the load line marks.

 

What I'm interested in iss the changing between the "big work" with the 6 mm plywood on the one hand (I never had without building a scratcher for cats and installing a truss for a child's swing with joisthanger five years ago. I fogot the construction of the high sleeper several years ago with a wrongly adjusted bubble level...  So my tooling partly is too rough - on the other hand I've got some very fine files, tiny cutters and an extra hand with magnifier but the tooling between... there an abyss gives a yawn

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Oh you are rigt, John. And to make matters worse S/S Warkworth built from iron - not from steel. So all the knowledge we finde is useless. I'll have to "digg deeper" to find the right normenclatur for the thicknesses and measurement of rivets and plates, The dimensions of angeliron, the measurements of brachings and so on.

To get the same solidity parts had to have bigger dimensions - this was why steel swiftly replaced iron. Due to the fact that shipbuilding from iron was a British business I'll have to look in the volumes of engeneering magazins to find the information I need.

 

Do you think it might be helpful to ask for information about the applied 1873/74 classification rules at Llody's Register in London?

 

That's what I like... the thrill of research - finding out newish information... to be honest I just have to rediscover them. But the first Llody's Register dated from 1899 - 1900...  :huh:

 

:dancetl6:  So the question is where to find these particular datasheets?  :dancetl6:

post-23296-0-97747800-1453596534.jpg

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Hello.

 

I worked today ion the inner structures of S/S Warkworth and in the both "Waines"  

 

Luckyly I found in "The colloier fleets" a coloured picture of S/S Broomhill owned by the same company - so I've got an idea of the couloring. What I've not got is the company's house flag. 

 

couloursdba7xp0lfg.jpg

 

 

I also found an interesting picture of S/S Lucania - showing the angle irons in their often appearence. Due to the fact that beside the engines room the coal bunkers are placed I'm a lucky guy. Why? Because

 

1st the walls are straight  

2nd tI don't have to show the bent irons of the frames and the inner side of the outside plating.   

 

201601211807538vw0e4x3tf.jpg

 

Here a top view of an engine  showing the imense number of pipes. All this can be seen through the open skylights. Here the  engine is placed aft, so the coal bunkers is more a cross bunker as in S/S Warkworth. 

 

file0604id0f1sv9xo.jpg

 

 

Here the situation in the plan of S/S Warkworth - it looking a lot simpler:

 

dampfmaschine1uiwcemoj9.jpg

 

 

To pick oput a 2nd point I've learned today I'm goint to show an interesting detail to you:

 

 

The anchorcranes:

 

The cranes for the anchors on the forecastledeck is a little detail I looked at today - sitting as an unwitting participant in a low-threshold New Years charity concert. So I had a plenty of time to think about anchorcranes in general and the ones I'll build in particular. Expecialy by not listening to third class singers beggaring my time with musical and operatta... So I was affraid of blueing my foremoon for the family. But I sat smiling between phrenetic people clapping their hands semi-rhytmicaly while the orchestra tries to play the famous Strauss's Radetzky march... So I cut everytig around off and managed to safe my time by escaping in the inner garden of my mind...  

  

thinking about a detail in the S/S Warkworth plan:

 

forecastledeckicma0d5fgj.jpg

 

It looks quite easy - but would it strong enought to take the weight of the ancre?

 

Some hours before the concert I leafed through the book and I found the answer to this question: 

 

ancrecraneshwj0bvozkf.jpg

 

The ancorcranes foundation is going through the f'c'stldeck - it's base placed on the balasttank's top... but noting is shown in the drawing of S/S W'w'th... it just schow's a mixture of the profile outline and waterline's drawing... bad luck to me. 

 

 fundation12ydzlki6e.jpg

 

Here a little "photomonatge" of W'w'th showing the position of the hyotothetical prolonguationpoints of the ancrecranes:

 

ancrecraneswwt3jey4gt7cq.jpg ancrecraneswwtztay43unic.jpg

 

But the problem is in the position of the foundations... Do the pierce throught the ship''s side??? To figure this out I've to make a drawing of the f'c'st'l deck - by integration of the former lines to carve out if  I need a plinth at the hulls inner side.

 

These were the cogitations I dealt with today... nothing to see from on the hull at the moment... but I think it is unavoidable when I want to open the hatches and give a look in the cpmpanionways. You're right to say nothing can be seen - the lowerpart of the cranes are eventually running through the fire- and seamens beds!!!  Or behind a wooden cladding... why do I burden my brain with those trubbles? 

 

 

There are no rails for the anchor chains - can this be right - or am I spoilt by the Navy Yard's battleship f'r'c'stl's accourtrement?

  

:huh: The next problem is with the rudders chain - where is it joining the rudder's quaterwheel and the two helmsman's wheels!  :huh:

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

The Radetzky March? No-one ever seems to know whether to clap on the beat or off, in my experience! (Generally, people hedge their bets and clap in between.)

 

The extensions of the cranes would probably bend to conform with the hull inside. They would not pierce the hull. 

Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series  http://trafalgar.tv

Link to comment
Share on other sites

Hy druxey,

 

so eveybody should avoid claping at all :P...

 

Okay the anchor cranes riveted me - I'll make a proper multiview orthographic projection on tracing paper to get rid of these bunch of doubts & questrions.

 

The desing of the modes is changed  now. 

 

The next step is the modelmodel of the saloon and the forecastel: 

 

The question to the inner structure of the forecastel is the folowering one:

 

What a bout the anchorchains way to the chain's bunker under the sea- & fireman's quater? The topviel shows a chainstopper to uns and an opening foreward where the chain seems to run trough down to the anchor's hawse. 

But if there were no hawes in the hull's side - if the anchors were stored on the forecastel's sides - as before the stockless anchor? 

But as  "anchor" in The New Encyclopædia Britannica. Chicago:Encyclopædia Britannica Inc., 15th edn., 1992, Vol. 1, pp. 377-8 tells us it was invented in 1821. In teh profile drawing there is no anchor at all... What do the specialists say... anchor hawes in the hull's sides for a stockless anchor or not in 1873/74?

 

The question is - what shall I show if the stariwell's door is open? 

So I'll have to build a cardboard model of the forecastle to get a "feeling for the inner structures".

 

 

 

The saloon is a bit more complicated because I'd like to show a lot of it through the open skylight. And I want to show the captain's cabin, too. 

The stairs seem to go down very fast and the stairs plunge. You can look down though the open hatch so I need to  built the detail very meticulous. The Innerside of the stair well will be made from bright wood - also the saloon needs to be pale. 

There is an open fireplace in the saloon the problems witzh the smoke's disposal you can read here: 

http://modelshipworld.com/index.php/topic/12596-ss-warkworth-an-early-steamer-not-too-big-please/?p=384966

 

This is the prelude to the "modelmodel" - here we're dealing with building. I searched around and found some pictures of staircases and openfireplaces - here the best I could get.

  

 

 

post-23296-0-67970000-1454271124_thumb.jpg

post-23296-0-42059200-1454273395_thumb.jpg

post-23296-0-64224100-1454274923_thumb.jpg

post-23296-0-77788700-1454275868.jpg

post-23296-0-48310600-1454275888_thumb.jpg

post-23296-0-76905300-1454276003_thumb.jpg

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Hello good news!

Jim Lead told me the "open fireplace" may only be a symbol -and so I  decided to change it into a stove. This due to the factum that this is a small collier and not a greyhound of the atlantic. ... and I am able to position the stove easyly directly under the chimney/funnel. 

 

In the drawings - the cut lower decks are all horicontal - no crowning as on the main and well deck.

Here a rough scetch to show what I speak about.

So the ceiling is curved the floor is straight/even/smooth. Does this repeat in the officer's rooms, too?

post-23296-0-34614300-1454313945_thumb.jpg

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Hello,

today I started to saw... to get a feeling for wood and for the room ocupied by the "Emptyness" of the saloon where I have to take off the plywood out of the bulkheads.  As I fear to be wrong I cut the wood on the small saw form Proxxon  without mesuing - directly from the  drwaing. laying the  paper and thewood on the sawing table... 

 

Here a first arrangement of my results... 

post-23296-0-76789600-1454692412_thumb.jpg

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Just found this thread, much appreciated as ships of this era are, in my view, rather neglected. Great work on the research and I'm looking forward to the build very much. Incidentally, I think the date written on the plan in your first post is actually Fby [February] 8th 1875. I think the ii is just a decorative part of the underline. But I can't help on whether it is a launch date or something else.

 

Greg

Edited by SailorGreg
Link to comment
Share on other sites

Thanks a lot, Greg,

 

that's very good news to me...

To understand my way of building so oveercautious is that I'm struggeling with a plenty of my own inexperience, nescienceand a leck of knowledge about early coasters and steamships. It's a completly new scope to me. So every pice of a jigsaw helps completing the picture - so I can now rub out this one questionmark.  

 

I decided to  giv a flat ceiling to the  saloon by lowering the ceilling...  

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

One thing that will help immensely-- if you have not already done so-- is to compile all dimensions that you have and use those as your guidance, even when they don't agree with drawings. If your plans have a table of offsets, that would be very useful.  I like the idea of building in 1:35 scale, as there are many very nice figures and details in that scale that can be used or adapted.  The more you have a set of "good" numbers to drive your work, the less you will have to worry about plan distortion, line variance, etc...

 

When setting up stations on the keel, determine all of your bulwark positions to the center of whatever material you are using, so that you can control spacing and tolerance stack-up.  Having a nice straight keel is critical for a ship of model of this size and aspect ratio, and being 'fussy' about the dimension numbers in the beginning makes the modeling so much easier in later steps.  (Of course, I only know this because I have tried the "don't worry, just jump in!" approach instead of the "fussy" approach--it did not work nearly as well... :( )

 

I am really looking forward to seeing your continued progress...

Link to comment
Share on other sites

Thanks a lot Bob Marvin...

this was very helpful.

At the monet I'm murmuring with my body plan.. due to the fact that the baseline solpes a bit to the outsuide from the centerline... So I'll have to recopy my bodyplan...and then I'll have to redraw every single bulkhead again - out of the profile... to decide where the severeal details will be positionated. The engine room is a good example:

 

The  steam-engine may

 

a) stand on a massive pedestal as a foundation 

 

or

 

B) the hole floor is in a raised position

 

So I'll have to decide what might be more realistic... Well is this importand?

 

Yes it is - because when I  add a step in the engine room's floor I will have much more material at the bulkhead No. 52 and No. 68 both weakened by the  hull form starting to get slimmer towards the after part of the hull. So Iit is a good solution to design it in this way...

 

So every Information I get is changing a plenty of other  older informations I have had - so I'm in a precess of enhancements.

 

As I've not got a table of offsets I've choosen one of the most completed plans in the hole Serie of Waine's books I could have choosen at all. there might be more detailed linesplanes - but than I'd not have a Profile with Details, or on the other Hand I may have choosen a more detauiled profile without a good lineplan. (The only execpion will be S/S Arundel where I've found coloured pictures from her last collier voyage in the mid 70th... but she is 325 feet long... that woould give a enormoues monstrum of 2 3/4 meters long ... enough to bulit a real oceangoing RC model with a livesteam engine in her hull...  able really to sail in the North Sea... an idea to dream about for the next years... even in 1/48 she will be 2,06 meters long.

 

So I'm going to correct the bodyplans copies and copuie them through transparent paper to get lighter lines and adding the inner structures of the hull from the profile. Dr. Murphy is so right: "Nothing is as easy as it looks... everything needs longer than you think... if anything can go wrong it will." 

But I figured this mistake out - and so I can avoid the fiollowing problems now - and I dont have to restore the model later when I MAY HAVE ascertained them... or being forced to burn her down in the old ways of the viking's.

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Okay... now we are here...


some poems rhyme...


some poems don't rime...


some are disgusting...


 


the hull will come through a door when I tilt her by 45°  to"shorten" her...


but I testet it with my 1/36 printouts...


and frigtheningly can never reach the floor...


when I add masts and rigging...


So I'll have to fish the 1/48 plan copies out...


of my pile of paperrolls...


Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Ah yes - it is always a good idea to make sure that your creation can be moved from the workshop. I learnt this when I was young from one of my secondary school teachers.  He had taken up sailing as a hobby. For this he built a dingy hull in the front room of his house. When complete it was a beautiful piece of work. Sadly it would not pass through window or door. So to get it out he had to saw it in half!

Edited by ianmajor

Ian M.

 

Current build: HMS Unicorn  (1748) - Corel Kit

 

Advice from my Grandfather to me. The only people who don't make mistakes are those who stand back and watch. The trick is not to repeat the error. 

Link to comment
Share on other sites

(...)So to get it out he had to saw it in half!

 

:o ...and so he invented the half-model.

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Hello friends,

 

the reductzion of the scale started with a little overview scalked to 1/48... a new Scaleman is in work... from a figures set of the Royal Flying Corps.

 

So this evening I worked on some inner issiues of the model.

 

a)

Luckyly the stircase is now 27mm high... and as we have to accommodate nine steps... we have to use 3mm high stair treads.

 

B)

As  I figured out that the dunky boiler will be hidden behind the Scotch boiler and hardly anything of it will be seen - iI decided to cut it into half... k.i.s.s. = keep it short & simple

 

c)

the main mast is not shown in the profile under deck. As there is a bulkhead between engineroom and aft hold the mast must be fixed somewhere - I designed two differend affixings for the mast step... the red and the blue one. 

 

d)

...or might it be a meststep to become narrower to the end and "hitting" the roof of the "proeller shaft's tunnel" (as we call it in German) I founf this  kind of ending a mast in the hull so some drawings of ironclads as far as I can remember.

 

Which one is right - blue, red or maroon? 

 

 

I also found  

 

- some nice colouring of the engineroom and the prpeller shaft's tunnel. 

- several details for a donkey boiler

- an intersting anchorwich drven by steam but without scale

- a wounderful two cylinder life steam engine... but I'm looking for plans/drawings

- some details of a cable tier

- two pictures of the steamers after construction

- and some nautic paraphernalia

post-23296-0-16448500-1455395263_thumb.jpg

post-23296-0-04190200-1455395273_thumb.jpg

post-23296-0-76380400-1455395288_thumb.jpg

post-23296-0-02907500-1455395327_thumb.jpg

post-23296-0-40233000-1455396130_thumb.jpg

post-23296-0-44648800-1455396405_thumb.jpg

post-23296-0-32709000-1455396561_thumb.jpg

post-23296-0-13112500-1455396649_thumb.jpg

post-23296-0-70081700-1455396722_thumb.jpg

post-23296-0-02979800-1455397521_thumb.jpg

post-23296-0-49462500-1455397529_thumb.jpg

post-23296-0-31467600-1455397536_thumb.jpg

post-23296-0-15340600-1455397608_thumb.jpg

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Moony,

 

That is an interesting two cylinder engine you have found but to my eyes looks too modern for the period of your ship. It has the appearance of a two cylinder double expansion compound. The low pressure cylinder has a slide valve, the high pressure cylinder appears to have a piston valve. For your period I would expect the valves to be all slide valves.

 

Is there any indication of the manufacturer of the engine on this ship? If so you could do a search on Graces Guide to British Industrial History < link to Engineer magazine index> which gives access to contemporary engineering publications. An example - from the 6th October 1882 edition of Engineer  I found this 1882 two cylinder compound marine engine <link to photo>  from  F.J. Harker, Stockton-On-Tees. Stockton is close to Newcastle. To me this is the sort of engine to look at. It also looks like the engine outline in your plans.

Edited by ianmajor

Ian M.

 

Current build: HMS Unicorn  (1748) - Corel Kit

 

Advice from my Grandfather to me. The only people who don't make mistakes are those who stand back and watch. The trick is not to repeat the error. 

Link to comment
Share on other sites

Thank you Ian,

 

I wrote something about engines and plans in here: 

 

http://modelshipworld.com/index.php/topic/12596-ss-warkworth-an-early-steamer-not-too-big-please/?p=380854 

 

But your lnks are very helpful - exspecially the drawing of the "S/S Singapore": I think I'll take it and try to clad it with wood to get the effect of Martin Baylis vertical Marine steam engine.

 

The boiler's drawing is from wikipedia.

As the rear side of the  boiler is only to see - the number of fireplaces unintresting. An intersting detail /quite one of the bigger ones) is the steam dome on the top... wikipedia called it a " Note the steam dome, a typically German feature".

And through the skylight this detail will be clearly seen. It is very big and high in the profile - mercyfully we only see the lower  rivete part of it. 

 

Edit:

My reconstruction of the engine top view in 1/36 - and how I constructed it from the profile plan.

And I have to admit that I really love this work of figuring out such details... It's so thrilling!!! It's much more than looking to a hand full of little details and cladding them on a kit to variate the kit you're building giving it a little individuality. 

 

NOW I start to understand the fascination of this hobby and the:

 

:sign:

 

 

 

post-23296-0-76119700-1455475629_thumb.jpg

post-23296-0-28142800-1455475689_thumb.jpg

post-23296-0-21311900-1455476102_thumb.png

post-23296-0-41291200-1455486729_thumb.jpg

post-23296-0-36457400-1455486756_thumb.jpg

post-23296-0-31402400-1455486815_thumb.jpg

post-23296-0-81145500-1455487448_thumb.jpg

post-23296-0-05552700-1455487829_thumb.jpg

post-23296-0-93619400-1455487863_thumb.jpg

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

An contemporary cylindrical boiler of 1865. The Swiss "P/S Rheinfall"  sunk in 1869 the boiler was raised in 1995. Two thinks are of intrest:

 

the opening with the clamps on an threaded rod - and the big rivets on a boiler built from several plates...

 

But much mor inmtrestin is the fact the the paddlewheeler sunk due to a boiler explosion... and the artefactum looks unharmed.

post-23296-0-46997000-1455488811_thumb.jpg

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Moony,

 

Interesting as you say that a boiler explosion sank the steamer. Looks like it was tube failure that caused it leaving the shell intact. The tube failure would probably have blown the burning fuel out of the grate in to the ship. Seriously bad news for the stokers.  

Ian M.

 

Current build: HMS Unicorn  (1748) - Corel Kit

 

Advice from my Grandfather to me. The only people who don't make mistakes are those who stand back and watch. The trick is not to repeat the error. 

Link to comment
Share on other sites

Yes defently, Ian, bad news for the  stokers & teh engenieres.

 

As my wife fall ill I had havce no time to do a plenty of work with S/S W'w'th. But I searched arround in the www and found some pictures of the rudder wich I could integrate in the plan... not a serious drawing just a scetch 

 

So I figured out that the  hull's lines from  bulkhead 34 - 46 are paralleel and the  bullkheards are the same in outline - but the floor is maximum 1/2 inch thick on a length of 5 1/4 inch. So decided to build an "engine and boiler room box" 5 1/2 inch long and 2 inch wide with a hight of 2 1/2 inch (green is the  box's floor  - red is the boilter's top view). The withe square on the  deckplan seem to be the bunkers top hatches - covered openings as filling ports for coal.

 

As this is very much too wide I am able to install the coaling chute  and the inner sides of the coal bunkers. Here my rough biro scetch from this afternoon - more an mnemoric device than a drawing.

post-23296-0-00859700-1456072990_thumb.jpg

post-23296-0-82896800-1456074657_thumb.jpg

post-23296-0-12814000-1456075495_thumb.jpg

post-23296-0-35974200-1456076778_thumb.jpg

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Here my first trial in the hatch of the coal bunker filler. 

Is this a reaklistic design with wingnuts? I didn't find any real designs in the web - exspecially contemporary... the best example I found where from S/S Kronprinz Wilhelm - a four funner greyhound of the North German Llody -. a vertical type and a quarter of an century too late. 

Does anybody deal with C.S.S. Alabama oder U-S-S. Keaserage where I may find some good example?

post-23296-0-13262400-1456085237_thumb.jpg

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

When I started to cut out teh first test bulkhead I realised that the mortice in the bulkhead and in the middleboard should end in a rectangular cut - as the pink line shows...

but it endet in the red line... and the red hachred part is a surplus standint in the way... so what can I do?

When I turn the bulkhead over I'll get an orange  mountain in the middel... 

What is your tip for using a KS 230 by Proxon in the right way?

post-23296-0-01908100-1456091836_thumb.jpg

post-23296-0-76929000-1456093191_thumb.jpg

Edited by Moony

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Jan, cut the mortice at 90 degrees to the board.  You'll probably need to make several passes and then clean up with a file.

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

Hy mtayler, that's a good idea. Thanks a lot. I'm affraid of breaking out the outside layer if the playwood. I'm not really goid with wood these days. But I'll try out if it will work. It may need several ways if repested trying. Thanks for your comment.

Give :pirate41:

 

Moony a.k.a. Jan

________________________________________________________

"S/S Warkworth"- 1875  (Scale 1/48)

One of the 1st modern iron-built Steam Colliers by Swan & Co. Newcastle on Tyne

 

___________________________________________________

While you're being creative, nothing is wrong.

There's no such thing as a mistake, and any

drivel may lead to the breakthrough.  

John Cleese 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...