Jump to content

HMS Dreadnought by rcmdrvr - Trumpeter - 1:350 - Waterline - PLASTIC


Recommended Posts

I have really had a tough time choosing my next project.  I really love warships that rely on engines for propulsion.  The problem with models of these ships is they tend to be plastic; not a medium that I have had much success, and the scales tend to result in parts and pieces that are really small and easily eaten by the floor.  I followed the build by patrickmil of the USS Curtis Wilbur and that got me excited to give plastics a go.  The 1:200 kits are quite a bit bigger than 1:350 but also pricier so I decided to go with the smaller scale (I passed on 1:700 as they are even smaller).  I decided on the HMS Dreadnought as it was a real game changer; ushering the era of the modern battleship.  I also made the decision to build this model for a waterline presentation.  I have visited several modelling sites and I am very impressed with that form of presentation.  The Trumpeter kit is not a waterline kit so at some point I will have to cut the hull off at just below the waterline.  Except for modifying the kit for waterline presentation; I will pretty much build it out-of-the-box.

 

While here is the obligatory photo of the box:

 

 

 

IMG_3440.JPG

Current Build:  HMS Dreadnought - PLASTIC - Waterline

Completed Builds:  USS Cairo by BlueJacket;  Nave Egizia by Amati;  Harriet Lane by Model Shipways

Link to comment
Share on other sites

I would like to do Dreadnought some day. However I want to build myself up to it as I am not confident I could do her justice at the moment. Good luck, I am looking forward to seeing how you progress with her.

Link to comment
Share on other sites

Thanks for the comments and likes.  The first step will be to assemble the basic hull and decking.  This also introduces the first challenge.  The decks of the Dreadnought were made of wood so I have to make a few large pieces of gray plastic look like wood.  I searched the internet and youtube and found several articles and videos on the process.  They seem to be variations on two themes.  One is to paint the entire deck with a wood color and then use washes (usually made from oil paints and white spirits) to highlight details and introduce multiple shades.  The other process is to use multiple layers of paint with lots of masking.  I chose the latter.  Here is the process.

 

First I painted all the decks with a light wood color.  I used XF-78 (Wooden Deck).  Next I used an INFINI Easy Cutting mat to make a bunch of .9 mm strips of masking tape of varing lengths from 5 to 20 mm.   I then randomly masked off portions of the deck using these tiny masking tape strips (tweezers are a must tool for this process).  I then repeated this process by airbrushing all the decking with XF-93 (Light Brown) and a bunch more masking tape strips.  This was followed by a layer of XF-55 (Deck Tan, which I will not use again) and tape and finally XF-59 (Desert Yellow).  This was allowed to dry overnight before I removed the masking tape.  The final step was to wash the decks.  I used Tamiya's brown panel liner as my wash for the main deck and a dark brown wash I mixed up for some of the upper decks.  I think I got an acceptable result but any suggestions for improvements for the next model will be greatly appreciated.  I hope the following photos give you some idea of the process and results:

 

 

IMG_3441.JPG

IMG_3443.JPG

IMG_3444.JPG

IMG_3445.JPG

IMG_3446.JPG

IMG_3447.JPG

Current Build:  HMS Dreadnought - PLASTIC - Waterline

Completed Builds:  USS Cairo by BlueJacket;  Nave Egizia by Amati;  Harriet Lane by Model Shipways

Link to comment
Share on other sites

Well, the basic hull is assembled so the time has come to cut off the bottom of the hull in order to facilitate a waterline presentation.  The first step in the process is to mark a cutting line around the circumference of the hull.  I did this with flexible tape.  I used the Trumpeter painting guide included in the kit to help me locate the cut.  I wanted to cut just below the indicated waterline.  It took a bit of time to eyeball the tape line to make sure it was straight so that the hull would sit flat when cut.  I used a dremel rotary tool and a cutting wheel to make the actual cut around the hull.  I had previously tested various cutting wheels and found that the very thin varieties break easily.  Because of all the internal supports separating the two pieces took a bit of effort.  You have to be very careful with the cutting tool to avoid cutting or damaging the plastic hull piece you want to keep.  The plastic tape helps here.  After completing the cut I had a hull that looked terrible but the melted plastic at the seam broke off easily and with a few minutes of sanding I ended up with flat hull that should facilitate a waterline presentation.  Here are some photos of the process:

IMG_3448.JPG

IMG_3449.JPG

IMG_3450.JPG

IMG_3451.JPG

IMG_3452.JPG

IMG_3453.JPG

IMG_3454.JPG

IMG_3455.JPG

Current Build:  HMS Dreadnought - PLASTIC - Waterline

Completed Builds:  USS Cairo by BlueJacket;  Nave Egizia by Amati;  Harriet Lane by Model Shipways

Link to comment
Share on other sites

Before I get into painting and attaching all the detail to the hull; I thought it would be a good idea to prime these basic hull pieces for painting.  This required me to maskoff all of the wooden decks.  Several years ago I purchased two masking tape cutting mats.  These mats make it easy to cut masking strips from .1 mm to 1 cm and circles of many different radius'.  They were a godsend in this masking project.  There were alot of projections that required me to mask the wooden deck around them.  I generally did this by cutting masking tape into 5 and 10 cm lengths and from 1 to .5 mm in width.  I ended up cutting hundreds of these masking tape pieces.  I would guess that it took me about 8 hours to mask off the decks.  I then airbrushed the primer.  I used black primer thinned 50% with levelling thinner.

 

After priming; it hit me that this would be a good time to cut the foam block display base and position the hull and cut the well.  I used green craft foam (insulation) sold at the local big box hardware store.  I used a foam cutter to cut out the rectangle for the base.  I then used the hull to trace out its position on the foam and used various cutting knives to cut and chip out the well that the model will sit.  I will now set this aside and get back to painting the basic hull.  

A few photos of my progress:

 

 

IMG_3456_resized.JPG

IMG_3457_resized.JPG

IMG_3458_resized.JPG

IMG_3459_resized.JPG

IMG_3460_resized.JPG

IMG_3461_resized.JPG

Current Build:  HMS Dreadnought - PLASTIC - Waterline

Completed Builds:  USS Cairo by BlueJacket;  Nave Egizia by Amati;  Harriet Lane by Model Shipways

Link to comment
Share on other sites

Back to painting the basic hull.  I decided to do a little pre-shading by mottling the primer with some white before painting the first color coat.  After that I laid airbrushed a light sea gray over the two hull pieces.  I then masked off the upper hulls and airbrushed a hull red color.  Finally I painted the black line at the waterline of the hull.  Is this painted line called the plimsoll line and did ships of this era, i.e. early 1900's have such a line.  I have ordered a book on the history of battleships and hope to learn a bit more about these ships.

 

Question for anyone who stumbles on this build.  Looking ahead I have to do some amount of rigging to make the presentation look more realistic.  How do you other builders go about finding out what the rigging looked like.  Photos of Dreadnought on the internet are very difficult use for this information as many are at a distant and dark.  I do have some box art that gives me some ideas.  I am not looking to make this an historic masterpiece, but some realistic rigging would look nice.  Any help would be appreciated.

 

Oh, some photos:

IMG_3463_resized.JPG

IMG_3464_resized.JPG

IMG_3465_resized.JPG

IMG_3466_resized.JPG

IMG_3467_resized.JPG

Current Build:  HMS Dreadnought - PLASTIC - Waterline

Completed Builds:  USS Cairo by BlueJacket;  Nave Egizia by Amati;  Harriet Lane by Model Shipways

Link to comment
Share on other sites

Funny you should ask....I just recently ordered "British Battleships of WWI" by R.A. Burt (I'm re-detailing an RC model of HMS Lion I scratch built in the 70's).

 

This book obviously includes Dreadnought. Here are a few pics which might assist you. In the line drawings of profiles in this book, signal halyards from the yardarms just kind of fade out in mid-air but they all were cleated on the flag deck which at least on Lion is one deck above the shelter deck which is one deck above the weather deck. One of the photos shows a set of signal halyards pretty clearly.

 

If you need a pic of some particular view, let me know and I'll check the other photos.

 

By the way, she looks great!  I've never airbrushed a model, I'm such a dinosaur....😭

 

Ian

PA290998.thumb.JPG.1d1dbe5e1251f3afffe45e26ffd6efae.JPG

PA291000.thumb.JPG.804aaff5da2729994a98ca16b4a87c2a.JPG

PA290999.thumb.JPG.75cdaa440f4a650708dd9cd2d481eb5d.JPG

PA291001.thumb.JPG.14117d86f81d8b8a3979d4bdbbb55aa1.JPG

PA291002.thumb.JPG.eed0e862a0b22b3f41d046ca881df292.JPG

Edited by Ian_Grant
Link to comment
Share on other sites

Thank you Ian_Grant for the pics.  Wow, it looks like rigging is going to be a MAJOR challenge.  I know I will not be able to duplicate everything, but I really want to get the basics.  In the line drawings, the tripple line that runs bow to stern and droops quite a bit along the way is very prominent.  In the photos, I am having trouble making them out.  Were then radio antenna?

Current Build:  HMS Dreadnought - PLASTIC - Waterline

Completed Builds:  USS Cairo by BlueJacket;  Nave Egizia by Amati;  Harriet Lane by Model Shipways

Link to comment
Share on other sites

With the basic hull essentially assembled and painted it is time to tackle all the little fiddely parts.  I have to admit that it can get a bit tedious to cut them from the sprue, clean up the seam lines; fill the ejection spots (although there were few of these on this kit) and paint.  Painting can also be a challenge.  I have made up alot of parts holders by attaching the smallest alligator clips I can find to toothpicks.  I can clip these to some very small parts and then stick in foam to hold for painting.  Of course, when these little parts are glued to the model you must remove the paint from the part and the location on the hull if you want a good joint.

 

I did run into one problem while working on the small parts.  The upper main mast styrene was so thin that it crumbled and broke when removing from the sprue.  I then used short lengths of brass wire in various guages to recreate the broken parts.  It required a little soldering; a skill I have not acquired; but I think I did OK.

 

The following are some photos of progress to date:

 

IMG_3469_resized.JPG

IMG_3470_resized.JPG

IMG_3471_resized.JPG

IMG_3472_resized.JPG

IMG_3473_resized.JPG

IMG_3474_resized.JPG

IMG_3475_resized.JPG

Current Build:  HMS Dreadnought - PLASTIC - Waterline

Completed Builds:  USS Cairo by BlueJacket;  Nave Egizia by Amati;  Harriet Lane by Model Shipways

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...