Chuck

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

Chuck I always enjoy seeing your updates, always something new to learn, and yes your workmanship is inspiring.
 
Michael

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

Guys
 
All I can say is that I am careful and slow to a fault.  Its tough to get stuff done this way.   But I do agree everyone should just slow down.  Its what I recommend  a lot of folks to do...
 
Anyway...back to Cheerful.
 
I was able after two attempts to shape the boom crutch and create a procedure for doing so.  The key was starting with a much thicker piece and making the boom crutch a bit over-sized to start.  I cut out the boom crutch on a piece of 1/4" thick boxwood and carefully adjusted for three angles.   When completed it will be just 1/8" wide to match the width of the fashion piece.  Now that the starboard side is complete I can do the other and take pictures at every step.  This is certainly one piece that needs slow and attentive care to the angles involved.  The boon crutch must be turned inboard slightly so the boom can actually sit in it.  This is tough because the fashion piece and the side of the hull goes in the opposite direction!!!   This one piece took me over four hours to produce, shape and paint to a finish I found acceptable.
 
A few careful reference marks and filing...then turn the piece inward and you are good to go!!!   I will have a step by step soon.  You can see the second boom crutch over-sized and ready to shape in one of the photos.  Note the tail is left long so the proper angles can be created while sanding it shorter.
 
Because the boom crutch was painted black it might be hard to see in these photos but essentially the boom crutch must match the angle of the fashion piece when viewed from the side and from astern in two planes while being turned to line up with the path of the boom (or the main mast).  All while hiding the seam between the two pieces...thank God it is supposed to be painted black.  
 

 

 

 

 

Timberheads are completed....now on to the boom crutches.  Just a word about those boom crutches.  These are probably some of the trickiest parts of the model to make.  There are going to be some crazy angles to create and much trial and error.  I expect to make quite a large pile of bad boom crutches.  This is for the benefit of all those building the model as well.  You will no doubt have a large pile of discarded crutches also.  I will do my best to explain how I make them step by step.  
 

 

 

 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

Guys
 
All I can say is that I am careful and slow to a fault.  Its tough to get stuff done this way.   But I do agree everyone should just slow down.  Its what I recommend  a lot of folks to do...
 
Anyway...back to Cheerful.
 
I was able after two attempts to shape the boom crutch and create a procedure for doing so.  The key was starting with a much thicker piece and making the boom crutch a bit over-sized to start.  I cut out the boom crutch on a piece of 1/4" thick boxwood and carefully adjusted for three angles.   When completed it will be just 1/8" wide to match the width of the fashion piece.  Now that the starboard side is complete I can do the other and take pictures at every step.  This is certainly one piece that needs slow and attentive care to the angles involved.  The boon crutch must be turned inboard slightly so the boom can actually sit in it.  This is tough because the fashion piece and the side of the hull goes in the opposite direction!!!   This one piece took me over four hours to produce, shape and paint to a finish I found acceptable.
 
A few careful reference marks and filing...then turn the piece inward and you are good to go!!!   I will have a step by step soon.  You can see the second boom crutch over-sized and ready to shape in one of the photos.  Note the tail is left long so the proper angles can be created while sanding it shorter.
 
Because the boom crutch was painted black it might be hard to see in these photos but essentially the boom crutch must match the angle of the fashion piece when viewed from the side and from astern in two planes while being turned to line up with the path of the boom (or the main mast).  All while hiding the seam between the two pieces...thank God it is supposed to be painted black.  
 

 

 

 

 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

Guys
 
All I can say is that I am careful and slow to a fault.  Its tough to get stuff done this way.   But I do agree everyone should just slow down.  Its what I recommend  a lot of folks to do...
 
Anyway...back to Cheerful.
 
I was able after two attempts to shape the boom crutch and create a procedure for doing so.  The key was starting with a much thicker piece and making the boom crutch a bit over-sized to start.  I cut out the boom crutch on a piece of 1/4" thick boxwood and carefully adjusted for three angles.   When completed it will be just 1/8" wide to match the width of the fashion piece.  Now that the starboard side is complete I can do the other and take pictures at every step.  This is certainly one piece that needs slow and attentive care to the angles involved.  The boon crutch must be turned inboard slightly so the boom can actually sit in it.  This is tough because the fashion piece and the side of the hull goes in the opposite direction!!!   This one piece took me over four hours to produce, shape and paint to a finish I found acceptable.
 
A few careful reference marks and filing...then turn the piece inward and you are good to go!!!   I will have a step by step soon.  You can see the second boom crutch over-sized and ready to shape in one of the photos.  Note the tail is left long so the proper angles can be created while sanding it shorter.
 
Because the boom crutch was painted black it might be hard to see in these photos but essentially the boom crutch must match the angle of the fashion piece when viewed from the side and from astern in two planes while being turned to line up with the path of the boom (or the main mast).  All while hiding the seam between the two pieces...thank God it is supposed to be painted black.  
 

 

 

 

 

Timberheads are completed....now on to the boom crutches.  Just a word about those boom crutches.  These are probably some of the trickiest parts of the model to make.  There are going to be some crazy angles to create and much trial and error.  I expect to make quite a large pile of bad boom crutches.  This is for the benefit of all those building the model as well.  You will no doubt have a large pile of discarded crutches also.  I will do my best to explain how I make them step by step.  
 

 

 

 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

Guys
 
All I can say is that I am careful and slow to a fault.  Its tough to get stuff done this way.   But I do agree everyone should just slow down.  Its what I recommend  a lot of folks to do...
 
Anyway...back to Cheerful.
 
I was able after two attempts to shape the boom crutch and create a procedure for doing so.  The key was starting with a much thicker piece and making the boom crutch a bit over-sized to start.  I cut out the boom crutch on a piece of 1/4" thick boxwood and carefully adjusted for three angles.   When completed it will be just 1/8" wide to match the width of the fashion piece.  Now that the starboard side is complete I can do the other and take pictures at every step.  This is certainly one piece that needs slow and attentive care to the angles involved.  The boon crutch must be turned inboard slightly so the boom can actually sit in it.  This is tough because the fashion piece and the side of the hull goes in the opposite direction!!!   This one piece took me over four hours to produce, shape and paint to a finish I found acceptable.
 
A few careful reference marks and filing...then turn the piece inward and you are good to go!!!   I will have a step by step soon.  You can see the second boom crutch over-sized and ready to shape in one of the photos.  Note the tail is left long so the proper angles can be created while sanding it shorter.
 
Because the boom crutch was painted black it might be hard to see in these photos but essentially the boom crutch must match the angle of the fashion piece when viewed from the side and from astern in two planes while being turned to line up with the path of the boom (or the main mast).  All while hiding the seam between the two pieces...thank God it is supposed to be painted black.  
 

 

 

 

 

Timberheads are completed....now on to the boom crutches.  Just a word about those boom crutches.  These are probably some of the trickiest parts of the model to make.  There are going to be some crazy angles to create and much trial and error.  I expect to make quite a large pile of bad boom crutches.  This is for the benefit of all those building the model as well.  You will no doubt have a large pile of discarded crutches also.  I will do my best to explain how I make them step by step.  
 

 

 

 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

Since there is nothing on the tube tonight I went ahead and glued the bulkheads into position.   This was something I wanted to do quickly so I get get a sense of the overall shape of this cutter.   I will start framing the gunports tomorrow.  You will notice the 2nd bulkhead at the bow has no extensions.  They wont be needed because the forward-most port will be framed there.  No warping which is great....straight as an arrow. 
 

 

Finally got the coppering done on the hull. added the false keel. Pegged it the same way I did the Cap Rail to make sure it held permanently. Plated & painted the rudder. Added eye bolts for the rudder pendants. used a strip of the copper tape for the iron plate with the eye bolts.
 
Still not sure what I'll do about the copper bottom. I want it to patina at least some. I don't like how bad the corners are snagging & it is impossible to never touch them with your hands as you are working on the ship. Hope no fingerprints show up later. Once the patina starts will it continue if you seal it or will the process stop at that point?
 
 

While working on the hull planking, I managed to get a few of the deck fittings completed. The gratings were made completely from scratch. Inspired by Chuck's kit tutorial, I was able to come up with a method to complete them.The Windlass was made from the kit.
 
After the gratings were cut on the table saw, I edge bent them to the approximate camber.

 
After bending back each grating slightly to the exact camber, 1/32" tabs were glued to the bottom of each grating for support.

 
Similar to the one from the kit, the gratings were then placed in a jig I made on the table saw.

 
The grating strips were inserted into the jig. Two temporary grating strips were inserted, one at each end, to keep the gratings parallel to one another. After making sure that everything was square, I glued .045 x .045 flat strips to the grating strips to complete the grating.

 
I made this jig for establishing the roundup once the grating and coaming were combined.

 

 

 
I had a lot of fun making the Windlass. Again, I decided to spray paint the colors. This photo shows the setup for spray painting.

 
The completed Windlass

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky. 

indeed I meant every word.  I enjoy the company.
 
As promised here are some step by step for making those pesky boom crutches.  Its important to start with an extra thick piece and cut the crutches out so the tail is extra wide also.
 
You will soon see why.
 
I find it easier to concentrate on one angle at a time.  To get these pieces positioned properly you must get the four angles done separately....one step at a time.
 
Start by filing the fashion piece flush with the cap rail.
 

 
Then viewing the boom crutch from the stern try and establish the correct first angle.  This would be the angle of the fashion piece along the transom as shown below in green.  You do this by filing the bottom of the crutch stem.
 

 
Then turn your attention to the angle when viewing the crutch from the side.  You are trying again to establish the fore/aft angle of the fashion piece as shown below.  This is why you made the crutch so much wider and cut it out of 1/4" thick boxwood.  Sand it to shape with a file.
 

 
Then.....we have to make the boom crutch face the lower mast.   On most models I see they are facing forward or even outboard.  This wouldnt serve its purpose to well.   The reason for making the stem of the crutch wider is so you can turn the crutch to face the mast.  Note how the fore edge of the crutch is flush with the fashion piece...BUT the aft corner hangs off the fashion piece.  Mark the aft side of the boom crutch as shown below and file this bevel into the outboard edge.  The round crutch remains untouched.  You are only beveling the stem.   Then also bevel the inboard edge of the stem to complete it.
 

 

 
Its at this stage where I glued it in position.   Then I filed and sanded it further to shape.  I filled the joint with wood filler and sanded it smooth so the crutch and fashion piece looked like one piece.  Thank God it is going to be painted black.  The last angle we should concern ourselves with is the angle of the top of the crutches when viewed at the side.  This is easier done while it is glued into position.
 
See the angles established in red so the crutches match the sheer or are at least level rather than slanting upwards.  This is important and the bottom of the crutch....inside the crutch should also be addressed and angled downward slightly or at least leveled off if need be.  Think about how the boom would REST in each crutch when establishing the angle inside the crutch.
 

 
When you are done....do it all over again on the other side and try very hard to get a matching pair.  Note how the stems are not very long and the crutches are so very close to the top of the transom.  If you hide the seam well and paint it the results are very convincing.  You will no doubt have many parts added to the waste pile as I did.  These are a bit tricky.