Chuck

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

If they dont put them back on the site I will fish around for the master CD;'s I have and place them somewhere on this site.
 
Chuck

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

Thwarts and stern seats
 
The first step is to fit the risers.  There is a for and aft part and the by pre-bending these to fit the inner part of the hull they fitted well.  The main issue is to make sure that the port and starpoard risers are at the same height.  By measuring the height from the plans I found this fairly easy:

The next task was to fit the thwarts and the cockpit seats. All of these parts are in two pieces.  As Chuck points out, it is difficult to rebate a nice even edge particularly in AYC so all of these parts consist of a thick wide part with a thin narrower one glued on top.  For example here are the thwarts:
 

 
And the Cockpit seats ( only dry fitted here)
 
 

 
The side cockpit seats are painted red:
 

and finally the crosspiece an the Knees are fitted:

 
Next up is  to fit the rest of the thwarts permanently.
 
John
 
 
 
 

Oh its scary…one slip up and it will be hard to fix.  But that is true when you drill hawse holes and scuppers on any model.  A year of hard work and one slip up…poofff.

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

Just take a deep breath and go for it, Chuck! 
 
John

Oh its scary…one slip up and it will be hard to fix.  But that is true when you drill hawse holes and scuppers on any model.  A year of hard work and one slip up…poofff.

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

Oh its scary…one slip up and it will be hard to fix.  But that is true when you drill hawse holes and scuppers on any model.  A year of hard work and one slip up…poofff.

Seeing the results of your work, Chuck, one would not think that there are any modeling tasks that could possibly terrify you.

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

Many of you are curious about this photo.   Its floating around the forums without an explanation.  I brought my Medway Longboat to the New London show last week where it was photographed..   You may not be able to see it right away but yes I changed this Medway English longboat to be an American boat.   This model was used in the movie that I worked on last year which I talked about a while back.   I changed the flag and the nameplate on the model.  They wanted it to be American and have the Character's Name on the model.  They were going to slowly pan across it for the movie and wanted Ed Harris' character name very visible etc.
 
To my Surprise after spending a bunch time with him trying to teach him how to fake being a ship modeler,   Ed Harris signed the model.  But of course not the base....Black sharpie right across the hull.   No fixing that!!!  So rather than put the model back to its original English origin and remove the nameplates, I decided to just leave it as is.  It will make for a nice conversation piece.   The movie is supposed to come out in July I believe....It was about 10 degrees out the day he signed it.  The workshop was set up in the garage of the set.  I have no idea how they acted as if it wasnt freezing all the time.  I suppose that is why he is considered such a great actor.
 
Starring Ed Harris, Dustan Hoffman, Bill Murray, Gabrielle Union, Jenifer Coolidge, Pete Davidson and a bunch of others you would certainly know.   We shall see how the movie turned out!!!   At least I have a memento for the wonderful experience.
 

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

Thanks guys....Had a lot of fun and will be back this evening...
 


 
One Note
 
I was contacted while away with an issue about frame 2F.   Its really weird because I cant replicate this.  My laser files for this 3/16" thick top timber shows the correct part for the top timber.   No worries though.  This is an easy fix.  I have not been contacted by any others so it may even be a one off thing.  But if you have the same issue.  Just send me a PM or an email and I will send you a new set of top timbers for 2F right away.  
 
Dont reply here .....send me an email or PM!!!!  Include your name and address info as well.   I will ship immediately.   I will cut a whole bunch when I return and have them ready to ship just in case anybody else has this same issue.
 

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

the rings are made in the usual manner.  Wrapped around a 47 drill bit and parted with a razor saw. The bent wire is much lighter and thinner gauge.  In my case here…24 gauge for the split rings and 28 gauge for the codder pin bent and inserted into the deck.

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck
 

While I was away, I had taken a bunch of milled cedar strips of various widths.  All were 3/64" thick.   I spent my evenings planking the decks which was quite nice and relaxing.  My wife was also enjoying some wine from the local vineyards while working on her own relaxing projects while overlooking the Long Island Sound.
 
Not much to say about how to plank the decks as the gun deck and poop were planked like any other deck.  Just taper the strips following the provided deck plans.   You must cut around the hatches and coamings as usual.   These were the most difficult planks to cut but not awful.   It just takes careful planning and cutting.
 
These were the last two planks which I waiting to return home so I could photograph them before gluing them in permanently.
 

Here are some photos of the completed deck planking.   The forecastle deck planks were cut from a 3/64" sheet because of their curvature as I mentioned.  But the gun deck and poop were planked with strips.  The curves are not that severe and it was a lot easier this way.   Note the gentle curve of the planks.
 

NOW...how much deck planking should be added.   Its really just a personal decision.  What do like more....or less.
 
I have an extra strake on the gun deck where  the cannon will be located.  I dont particularly like when the carriage trucks are hanging over the edge if there were too few strakes.   But maybe you are OK with that.  This planking scheme matches the plans I provided but you guys can change to suit your sensibilities.  Looking at the photos you can see why I omitted all of the deck knees (hanging and lodging).  You can try really hard but would ever be able to see even a whisper of them.  It just doesnt make sense to add them with this planking layout.  I hope you will agree.
 


Next up will be something I have been blissfully ignoring.  Its a bit terrifying for any ship modeler. I will be drilling the scupper holes and hawse holes.   Usually I drill the scuppers after adding the waterway.  But this usually chips and frays the waterway.   So I am going to try something new.  I will drill the scuppers first and then add the waterway strip.   I will mark and file the waterway strip so it will hopefully not get damaged.  We shall see.
 
The hawse holes are a different story.  Those will require some really careful planning.
 
But waiting any longer to do these will only make them more terrifying. 
 
Chuck