Beef Wellington

Playing catchup, what a beautiful ship and excellent execution, love the finish, colours..everything just coming together so well.  Nicely done!

Looking very nice Mark, I can't help but feel this would make a nice kit.  Have you considered going there?

Looking very nice Mark, I can't help but feel this would make a nice kit.  Have you considered going there?

Looking very nice Mark, I can't help but feel this would make a nice kit.  Have you considered going there?

Looking very nice Mark, I can't help but feel this would make a nice kit.  Have you considered going there?

Looking very nice Mark, I can't help but feel this would make a nice kit.  Have you considered going there?

Thanks for following along this voyage everyone.    Things have settled down a bit and I'm getting some shop time.   So on with the build as time permits.. now where was I?   Oh...  the carvings have been set aside (again).  I probably have a mental block for them.      So it's back to the ship's boats.
 
I've basically dumped all the old formers and bits that had worked on as I just wasn't happy with the way they were turning out.   Felt like something was really amiss so I went off on a different tack.  I hope this time will be the magic one.  I've done a test boat (didn't complete it) that showed me the "true" path to enlightenment.  Or something like enlightenment.
 
I reworked a set of plans I bought and turned them into what I needed for the boats.   I also decided to attack the 6" boat first and work down to the 4". Disclaimer:  I sent the plans maker a copy of all the plans for these boats to see if they can use them.  I'm also buying enough kits (3) so the build will essentially be on a one-for-one basis.
 
After reworking the plans, I've cut the first pieces which are the keel, building jig and all the associated pieces out of boxwood.  I found that plywood un-glued itself or the glue went up on smoke and I ended up with charcoal.   There were two pieces of the build jig that I cut from 1/4" basswood and it's been cleaned up as necessary.   I'm currently removing the pieces, cleaning off the char as needed and putting together the keel and building jig.  I hope to cut out the ribs and planking from Swiss pear later this week.   There won't be twarts, rudder, oars, etc. inside this boat as it's the "bottom of the stack" as such and the next boat will fird inside this one.
 
The sharp eyed will detect a few errors in the photo such as a duplicate cutting due to my mispositioning the wood into the laser.   It's a "just in case" spare now.  There's at least one other obvious "I blew it" moment but those two parts have been corrected and recut.
 
There will be more pictures to come.
 
 

Thanks for the patience on this build, the advice, and the likes.
 
It's been slow going what with personal issues, re-cutting some pieces, etc.   Here's where I am on the this first ship's boat.  The build jig has been built and the keel and the two risers on each side are installed.  The risers still need a bit of tweaking as to some bits and pieces where the planking will run and then glue them into position.  I'm pretty pleased with how it's going just need more time and focus.   After the tweaks, the next step is to cut out the ribs and install them.  I see from the photos, I need to do some more clean up of the char on the keel and the risers.
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Good morning.

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....