Beef Wellington

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

I finished painting the cockpit seats.  I also added the knees atop the last thwart and the knees and bracket along the inside of the transom.  The knees on the transom were tricky but not too bad.  They need to be beveled along the sides and back to fit the angles of the bulwarks and transom.  Also note that the center bracket or panel on the transom was added to the top of the stern post and sanded flush.  But before doing so, the stern post was reduced in height about 1/16" first.  This allowed the top of the panel to sit flush with the top of the transom.  Once this was glued into position and the knees added on either side,  they were all sanded flush with each other so you couldnt see any seams.  I used some wood filler for this too.  Once painted it looks nice and clean.  The notch on the center of that panel is used as a guide to file that same notch through the transom as well.  You can see that in the photos. I hope that makes sense.
 
Next up working my way forward will be the windlass.
 


 
 

Installing the risers was up next.  They are designed in two pieces for each side.  They are laser cut with notches in them for the thwarts.  This means that the placement of these is crucial.  The very first thing I did was measure off the plan the distance from the top of the caprail down to the top edge of the riser.  I did this at every frame on both sides of the model so I was sure these would be placed at the same level port to starboard.  The aft piece is the first to be glued into position.  But I did add the nails ahead of time because I think it would be easier.  So I clamped it in position temporarily to mark the frame along the riser and then after unclamping, I drilled and inserted the fishing line for the nails.   This first piece is left a bit long just like I did with the planking.  So you need to mark the forward end in the middle of the frame and cut off the excess.  This is very important because the next section will butt against it and the thwart notches need to line up.  Its easy enough to do but you must be careful.  Then it was glued into position making sure that the top of aft end was level with the top of the bulkhead frame it sits against.  The cockpit seats will sit on top of this so they need to be level with each other. 
 
You could see the forward section waiting to be glued into position.  No trimming needed.  This just needs to be butt against the aft section tightly.
 

 
Here you can see both sections of the risers in position.

Then I made up the thwarts.  Like the floorboards these have a fancy edge.  Since scraping Cedar is problematic, I made each thwart in two layers glued together.  I just cleaned the char of the edges and glued the layers together creating an even fancy edge on both sides.
 
These are laser cut extra long as well.  You will need to cut them to length so they fit in the notches nicely.  You may have some that require some notching around the frames.  But its pretty straight forward stuff.  These are not glued in yet.  I will wait until I make the cockpit seats next and after some detailing on those which I will describe,  they will be glued unto position.  The center thwart with the cut away for the mast also needs detailing before it can be glued into position.  Its finally moving along and actually looks like a boat!!!  It wont be long now!!!
 
Feel free to ask me any questions.  This model really shows the beauty of the yellow cedar which I am really liking the more I use it.
 


 
 
 
 

Destruction...
 
Need to jump in and get going with the destruction to correct the gun ports so this doesn't derail me.  There will be 3 or 4 ports per side that need to be moved, so doing individually would not make sense.  Fortuitously, I had used a strip of 6mm wide box for the uppermost strake.  With one minor exception, the rough cut ports don't extend below this so replacing this one strake seems to be the way to go.
 
Started off on the port side using isopropyl alcohol and a sharp blade to try to pry the 1mm thick strip from the 1.5mm thick template.  Although I eventually got there, its a real dogs breakfast (mess).  I just couldn't get the isopropyl to penetrate where I needed it sufficiently without compromising the surrounding structures (the template is laminate strip which will de-bond as well if too much isopropyl is used).  As you can see in the pictures, a couple of shards got stripped away in the process where the box strip had been edge glued and but not sufficiently softened.  The isopropyl also got onto the painted surface below and marred the finish, so this will need touching up.  Once replaced, filled and finished, hoping this will not be noticeable.
 

 
Before tackling the starboard side, the approach needed to be amended to allow the isopropyl to penetrate more thoroughly and evenly.  Took a  while, drilled a multitude of holes in the strake to be removed and then applied the isopropyl.  Despite taking a while to drill, this was SO much easier and gave a MUCH cleaner result.  It also allowed the glued edges to soften sufficiently to debond cleanly.  Now the scary part is over, the strake can be replaced and the template ports filled before getting back to where I was with the channels....
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Greetings all
                      Thanks a lot for all your encouragement, help and likes. Well I am happy with how things are going now, at last. I have tidied up all the gunports and added the position of the wale line. The plank I have fitted is the first strip above the wale line. The gunports are not perfect because of my poor work cutting them out. Anyway I will now fit a couple more planks up towards the gunports, and then start cutting out the port side gun ports. Which should keep me happyish for a week or two. Once again thanks a lot DAVID

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

finished playing with the anchors, its far tro early for them and will just create more snags as i continue withe the rigging

Fore mast yards and Stun Yards

i love rigging, it takes me into another time (NOT LIKE DR WHO), i think its because it all goes together like a fine tuned engine, its nice to think that line does this and that one gets tied off there because blah blah blah

one dowl 8mm thick and two at 3mm gives me what is reqired for the lower yard on the foremast
used my lathe as a sanding tool and had a great few hours





that completes the basics but to be primed and painted then set up with accessories before being fixed to the build, however i always pin my spars in the relevant position, makes my life so much easier

good evening everyone
 
not much to show for the weekends work, still tidying up the front end lines and making sure they are going to the right place, all my points of reference differ,

the cathead was rigged and ancors made but for some reason i only have qty 2 and not 4, lol i dont think i can moan about it 7 years down the road

i dont quite know where the chain is fitted to on the hull near the flukes (when in the stowed position, so i am still experimenting 

Finding reference material to show the tie down points for rigging Mikasa has been less than precise, much less in fact. So, am doing the next best thing. "Kentucky windage". One of the main objectives is tying down so the rigging doesn't interfere with the ships boats, to be added after the rigging is done. 

Cheers Guys,
@ Dowmer - Well I had planked it but fortunately they were only short lengths, and pva is quite easily removed with the careful application of water.
@ Martin -  No tenons, and a little over size for this scale, but it does make for a decent weight.
@  Lou -  I borrowed them from the Galley, we use two weight systems over here and they are representatives of both imperial and metric systems. 🙂
@ Ferit - Thank you Ferit,  Chuck has  excelled with this model altho'  there are always  questions around boats of this era.😉
 
Post 42
Port lids -  an interesting exercise.
 As a small diversion I turn my attention to the stern port lids.

2730
The first very necessary job is to make a card template onto which the plank lines can be marked.

2728
Three boards are glued together onto which the template is transferred - then cut out and fine sanded to fit.
 
Gunport lids of Warships of this period consisted of two layers of board. An inboard vertical layer fitted within the port area, and a horizontal layer which fitted into the port rabbet.

2907
This the approach I have taken, as shown on these reject lids.
 
During the initial versions I noticed that the port side lid looked a tad smaller than the Starboard side. Much as I tried to ignore this it was sufficiently noticeable  to irk my eye, and I couldn't let it go.

2881
Rectifying the matter entailed enlarging the rabbet on the port side, very carefully using a scalpel and micro chisel.
A case of some earlier error coming back to haunt me.
 
 It took me three goes to get the lids right with the board lines matching those of the transom, and that fitted snugly within the rabbet.

2914
Fairly content with the end result.
 
For the lid straps and hinges I used Chuck's  little kit rather than thin brass strip which would entail a spot of silver soldering and blackening, an even more fiddly job that may have no better result.

2879
A bit of a test for my tired old eyes.
To represent the bolt heads on the straps I use a spot of pva on a needle point.
They were then painted with Admiralty Metal black paint.
The 28 gauge wire indicated for the hull mount seemed very flimsy to me and I scouted around for something a little more robust, and slightly more authentic.
 An alternative came in the form of  brass etched hammock crane arms left over from my Pegasus build.

2917
 0.7mm ø brass tubing was ca'd  into the ring and filed flush and a short length of the 28 gauge wire ca'd  into the tube.

2918
This gave a solid right angle onto which to hang the strap rings.

2938
This is quite a strong arrangement but in fitting the lids to the transom the tiny tube sections attached to the laser board straps gave way several times much to my irritation.

2937
What started as small diversion turned out to be a time consuming and somewhat frustrating exercise in fiddliness, at least there are only two lids and not a full set along the broadside.
 
Whilst on the subject of stern ports, I have puzzled just what are they for on Cheerful ? They are positioned far too high for any normal carriage gun to use.
On some cutter models I have seen there is a platform, which in the case of Cheerful would also cover the area between the seats of ease, allowing a gun to be sited at the correct level.
This is the arrangement shown on the deck plan of The Naval Cutter Alert by Peter Goodwin, described as 'platform deck over counter'.
 
Time to move on....
 
B.E.
01/10/2018
 

Hi all,   more work again today  she is getting closer and closer to completion,   anyway I cut the mid section of railing into two sections, the first one fitted in a nice short straight line between the 4inch gun mount shroud and the platform,  the next section continued on from the platform and forward, this section needed bending in two opposing directions, then glueing into place.
 
I did this for both sides  then turned my attention to the rear access hull ladder,  this has a platform at both ends and after assembling I fitted in the stowed position.
 
OC.

Hi all,  I started fitting the deck rails starting with the rear deck, after checking the location of the obstructions like the rear tubs, and also the rear accsess hull ladder,  it gave me the the opportunity to cut the railing into three pieces,   this worked quite well  I just sat them in a small smear of thick gorila pva.
 
Heres the dreaded pictures.
 
OC.

Hi all,
 
Firstly a Huge thank you for all the likes and comments.
So  I decided to pop the dry fitted parts on the ole girl and I took her outside to do a few more pics.
 
OC.

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Greeting Stergios, not sure if this helps.   I remember being very confused by this myself.  Here is what I did to solve the problem, I can't guarantee it is the correct solution, but sharing in case it gives you a better idea.  You can see its still work in progress!