Beef Wellington

Thanks all for the nice words, likes and continued interest.  Know its been a while, seems as if I hit some sort of 'modelers wall'.  Before I can really continue with the topsides, I needed to turn my attention to mounting the rudder.  This is something I've been putting off for quite a while, and proved to be a very frustrating experience.  I had initially delayed doing this to allow the copper to oxidize as much as possible just in case of any errant CA glue and prevent shiny spots.
 
The kit provides PE rudder and pintle straps, but for some reason I couldn't get comfortable with them.  On Snake, the staps come with holes and pins were inserted, but this was something that in retrospect look a little too clunky and out of scale.  Looking at pictures of period ships, the bolts/nails are quite a subtle feature similar to treenails in visibility.  I experimented with card and styrene strip  to make these from scratch, but in the end decided to go with the supplied PE parts.  I forgot to take a picture, but instead of premade holes, these have rather large circular indentations in them, I'm guessing to simulate the bolts.  To my eye they looked to far apart, and the holes too big.  I made a slight alteration to increase the number of bolts/nail heads by drilling additional indentations to simulate what was already there.  The rudder straps also needed to be shortened quite considerably to eliminate overhang at the rear of the rudder.  These were painted with "Admiralty copper" paint after experimenting with other similar Tamiya colours.
 
The main challenge I found was to attach these without marring the copper plates, and this proved to be quite the challenge as at first the CA glue wouldn't provide a good bond and needed to be reapplied.  Scratching the hull plates and inside surface of the PE seemed to get things strong enough. The rudder proved quite the challenge to mount as this had been made with a low (for me) level of tolerance following the AOTS plans which is documented earlier in the log.
 
Interestingly, the box artwork shows a spectacle plate, but there is nothing in the kit nor instructions.  This was simulated using painted card and eyebolts, but interestingly there is very little room for this, however this seems consistent with AOTS diagrams.  The ironwork on the lower counter ports used some PE parts from the "Badger" set which I had bought a number of years ago.  These looked a little more in keeping scale wise than what is provide in this kit.  I may add ring bolts and rings to these, but will likely not rig with line as I'm concerned this may be a visual distraction - personal preference of course.  Next up will be to attach the rudder chains which, nicely, are provided in the kit.
 

 

Thanks all for the nice words, likes and continued interest.  Know its been a while, seems as if I hit some sort of 'modelers wall'.  Before I can really continue with the topsides, I needed to turn my attention to mounting the rudder.  This is something I've been putting off for quite a while, and proved to be a very frustrating experience.  I had initially delayed doing this to allow the copper to oxidize as much as possible just in case of any errant CA glue and prevent shiny spots.
 
The kit provides PE rudder and pintle straps, but for some reason I couldn't get comfortable with them.  On Snake, the staps come with holes and pins were inserted, but this was something that in retrospect look a little too clunky and out of scale.  Looking at pictures of period ships, the bolts/nails are quite a subtle feature similar to treenails in visibility.  I experimented with card and styrene strip  to make these from scratch, but in the end decided to go with the supplied PE parts.  I forgot to take a picture, but instead of premade holes, these have rather large circular indentations in them, I'm guessing to simulate the bolts.  To my eye they looked to far apart, and the holes too big.  I made a slight alteration to increase the number of bolts/nail heads by drilling additional indentations to simulate what was already there.  The rudder straps also needed to be shortened quite considerably to eliminate overhang at the rear of the rudder.  These were painted with "Admiralty copper" paint after experimenting with other similar Tamiya colours.
 
The main challenge I found was to attach these without marring the copper plates, and this proved to be quite the challenge as at first the CA glue wouldn't provide a good bond and needed to be reapplied.  Scratching the hull plates and inside surface of the PE seemed to get things strong enough. The rudder proved quite the challenge to mount as this had been made with a low (for me) level of tolerance following the AOTS plans which is documented earlier in the log.
 
Interestingly, the box artwork shows a spectacle plate, but there is nothing in the kit nor instructions.  This was simulated using painted card and eyebolts, but interestingly there is very little room for this, however this seems consistent with AOTS diagrams.  The ironwork on the lower counter ports used some PE parts from the "Badger" set which I had bought a number of years ago.  These looked a little more in keeping scale wise than what is provide in this kit.  I may add ring bolts and rings to these, but will likely not rig with line as I'm concerned this may be a visual distraction - personal preference of course.  Next up will be to attach the rudder chains which, nicely, are provided in the kit.
 

 

Thanks all for the nice words, likes and continued interest.  Know its been a while, seems as if I hit some sort of 'modelers wall'.  Before I can really continue with the topsides, I needed to turn my attention to mounting the rudder.  This is something I've been putting off for quite a while, and proved to be a very frustrating experience.  I had initially delayed doing this to allow the copper to oxidize as much as possible just in case of any errant CA glue and prevent shiny spots.
 
The kit provides PE rudder and pintle straps, but for some reason I couldn't get comfortable with them.  On Snake, the staps come with holes and pins were inserted, but this was something that in retrospect look a little too clunky and out of scale.  Looking at pictures of period ships, the bolts/nails are quite a subtle feature similar to treenails in visibility.  I experimented with card and styrene strip  to make these from scratch, but in the end decided to go with the supplied PE parts.  I forgot to take a picture, but instead of premade holes, these have rather large circular indentations in them, I'm guessing to simulate the bolts.  To my eye they looked to far apart, and the holes too big.  I made a slight alteration to increase the number of bolts/nail heads by drilling additional indentations to simulate what was already there.  The rudder straps also needed to be shortened quite considerably to eliminate overhang at the rear of the rudder.  These were painted with "Admiralty copper" paint after experimenting with other similar Tamiya colours.
 
The main challenge I found was to attach these without marring the copper plates, and this proved to be quite the challenge as at first the CA glue wouldn't provide a good bond and needed to be reapplied.  Scratching the hull plates and inside surface of the PE seemed to get things strong enough. The rudder proved quite the challenge to mount as this had been made with a low (for me) level of tolerance following the AOTS plans which is documented earlier in the log.
 
Interestingly, the box artwork shows a spectacle plate, but there is nothing in the kit nor instructions.  This was simulated using painted card and eyebolts, but interestingly there is very little room for this, however this seems consistent with AOTS diagrams.  The ironwork on the lower counter ports used some PE parts from the "Badger" set which I had bought a number of years ago.  These looked a little more in keeping scale wise than what is provide in this kit.  I may add ring bolts and rings to these, but will likely not rig with line as I'm concerned this may be a visual distraction - personal preference of course.  Next up will be to attach the rudder chains which, nicely, are provided in the kit.
 

 

Thanks all for the nice words, likes and continued interest.  Know its been a while, seems as if I hit some sort of 'modelers wall'.  Before I can really continue with the topsides, I needed to turn my attention to mounting the rudder.  This is something I've been putting off for quite a while, and proved to be a very frustrating experience.  I had initially delayed doing this to allow the copper to oxidize as much as possible just in case of any errant CA glue and prevent shiny spots.
 
The kit provides PE rudder and pintle straps, but for some reason I couldn't get comfortable with them.  On Snake, the staps come with holes and pins were inserted, but this was something that in retrospect look a little too clunky and out of scale.  Looking at pictures of period ships, the bolts/nails are quite a subtle feature similar to treenails in visibility.  I experimented with card and styrene strip  to make these from scratch, but in the end decided to go with the supplied PE parts.  I forgot to take a picture, but instead of premade holes, these have rather large circular indentations in them, I'm guessing to simulate the bolts.  To my eye they looked to far apart, and the holes too big.  I made a slight alteration to increase the number of bolts/nail heads by drilling additional indentations to simulate what was already there.  The rudder straps also needed to be shortened quite considerably to eliminate overhang at the rear of the rudder.  These were painted with "Admiralty copper" paint after experimenting with other similar Tamiya colours.
 
The main challenge I found was to attach these without marring the copper plates, and this proved to be quite the challenge as at first the CA glue wouldn't provide a good bond and needed to be reapplied.  Scratching the hull plates and inside surface of the PE seemed to get things strong enough. The rudder proved quite the challenge to mount as this had been made with a low (for me) level of tolerance following the AOTS plans which is documented earlier in the log.
 
Interestingly, the box artwork shows a spectacle plate, but there is nothing in the kit nor instructions.  This was simulated using painted card and eyebolts, but interestingly there is very little room for this, however this seems consistent with AOTS diagrams.  The ironwork on the lower counter ports used some PE parts from the "Badger" set which I had bought a number of years ago.  These looked a little more in keeping scale wise than what is provide in this kit.  I may add ring bolts and rings to these, but will likely not rig with line as I'm concerned this may be a visual distraction - personal preference of course.  Next up will be to attach the rudder chains which, nicely, are provided in the kit.
 

 

Thanks all for the nice words, likes and continued interest.  Know its been a while, seems as if I hit some sort of 'modelers wall'.  Before I can really continue with the topsides, I needed to turn my attention to mounting the rudder.  This is something I've been putting off for quite a while, and proved to be a very frustrating experience.  I had initially delayed doing this to allow the copper to oxidize as much as possible just in case of any errant CA glue and prevent shiny spots.
 
The kit provides PE rudder and pintle straps, but for some reason I couldn't get comfortable with them.  On Snake, the staps come with holes and pins were inserted, but this was something that in retrospect look a little too clunky and out of scale.  Looking at pictures of period ships, the bolts/nails are quite a subtle feature similar to treenails in visibility.  I experimented with card and styrene strip  to make these from scratch, but in the end decided to go with the supplied PE parts.  I forgot to take a picture, but instead of premade holes, these have rather large circular indentations in them, I'm guessing to simulate the bolts.  To my eye they looked to far apart, and the holes too big.  I made a slight alteration to increase the number of bolts/nail heads by drilling additional indentations to simulate what was already there.  The rudder straps also needed to be shortened quite considerably to eliminate overhang at the rear of the rudder.  These were painted with "Admiralty copper" paint after experimenting with other similar Tamiya colours.
 
The main challenge I found was to attach these without marring the copper plates, and this proved to be quite the challenge as at first the CA glue wouldn't provide a good bond and needed to be reapplied.  Scratching the hull plates and inside surface of the PE seemed to get things strong enough. The rudder proved quite the challenge to mount as this had been made with a low (for me) level of tolerance following the AOTS plans which is documented earlier in the log.
 
Interestingly, the box artwork shows a spectacle plate, but there is nothing in the kit nor instructions.  This was simulated using painted card and eyebolts, but interestingly there is very little room for this, however this seems consistent with AOTS diagrams.  The ironwork on the lower counter ports used some PE parts from the "Badger" set which I had bought a number of years ago.  These looked a little more in keeping scale wise than what is provide in this kit.  I may add ring bolts and rings to these, but will likely not rig with line as I'm concerned this may be a visual distraction - personal preference of course.  Next up will be to attach the rudder chains which, nicely, are provided in the kit.
 

 

Thanks all for the nice words, likes and continued interest.  Know its been a while, seems as if I hit some sort of 'modelers wall'.  Before I can really continue with the topsides, I needed to turn my attention to mounting the rudder.  This is something I've been putting off for quite a while, and proved to be a very frustrating experience.  I had initially delayed doing this to allow the copper to oxidize as much as possible just in case of any errant CA glue and prevent shiny spots.
 
The kit provides PE rudder and pintle straps, but for some reason I couldn't get comfortable with them.  On Snake, the staps come with holes and pins were inserted, but this was something that in retrospect look a little too clunky and out of scale.  Looking at pictures of period ships, the bolts/nails are quite a subtle feature similar to treenails in visibility.  I experimented with card and styrene strip  to make these from scratch, but in the end decided to go with the supplied PE parts.  I forgot to take a picture, but instead of premade holes, these have rather large circular indentations in them, I'm guessing to simulate the bolts.  To my eye they looked to far apart, and the holes too big.  I made a slight alteration to increase the number of bolts/nail heads by drilling additional indentations to simulate what was already there.  The rudder straps also needed to be shortened quite considerably to eliminate overhang at the rear of the rudder.  These were painted with "Admiralty copper" paint after experimenting with other similar Tamiya colours.
 
The main challenge I found was to attach these without marring the copper plates, and this proved to be quite the challenge as at first the CA glue wouldn't provide a good bond and needed to be reapplied.  Scratching the hull plates and inside surface of the PE seemed to get things strong enough. The rudder proved quite the challenge to mount as this had been made with a low (for me) level of tolerance following the AOTS plans which is documented earlier in the log.
 
Interestingly, the box artwork shows a spectacle plate, but there is nothing in the kit nor instructions.  This was simulated using painted card and eyebolts, but interestingly there is very little room for this, however this seems consistent with AOTS diagrams.  The ironwork on the lower counter ports used some PE parts from the "Badger" set which I had bought a number of years ago.  These looked a little more in keeping scale wise than what is provide in this kit.  I may add ring bolts and rings to these, but will likely not rig with line as I'm concerned this may be a visual distraction - personal preference of course.  Next up will be to attach the rudder chains which, nicely, are provided in the kit.
 

 

Thanks all for the nice words, likes and continued interest.  Know its been a while, seems as if I hit some sort of 'modelers wall'.  Before I can really continue with the topsides, I needed to turn my attention to mounting the rudder.  This is something I've been putting off for quite a while, and proved to be a very frustrating experience.  I had initially delayed doing this to allow the copper to oxidize as much as possible just in case of any errant CA glue and prevent shiny spots.
 
The kit provides PE rudder and pintle straps, but for some reason I couldn't get comfortable with them.  On Snake, the staps come with holes and pins were inserted, but this was something that in retrospect look a little too clunky and out of scale.  Looking at pictures of period ships, the bolts/nails are quite a subtle feature similar to treenails in visibility.  I experimented with card and styrene strip  to make these from scratch, but in the end decided to go with the supplied PE parts.  I forgot to take a picture, but instead of premade holes, these have rather large circular indentations in them, I'm guessing to simulate the bolts.  To my eye they looked to far apart, and the holes too big.  I made a slight alteration to increase the number of bolts/nail heads by drilling additional indentations to simulate what was already there.  The rudder straps also needed to be shortened quite considerably to eliminate overhang at the rear of the rudder.  These were painted with "Admiralty copper" paint after experimenting with other similar Tamiya colours.
 
The main challenge I found was to attach these without marring the copper plates, and this proved to be quite the challenge as at first the CA glue wouldn't provide a good bond and needed to be reapplied.  Scratching the hull plates and inside surface of the PE seemed to get things strong enough. The rudder proved quite the challenge to mount as this had been made with a low (for me) level of tolerance following the AOTS plans which is documented earlier in the log.
 
Interestingly, the box artwork shows a spectacle plate, but there is nothing in the kit nor instructions.  This was simulated using painted card and eyebolts, but interestingly there is very little room for this, however this seems consistent with AOTS diagrams.  The ironwork on the lower counter ports used some PE parts from the "Badger" set which I had bought a number of years ago.  These looked a little more in keeping scale wise than what is provide in this kit.  I may add ring bolts and rings to these, but will likely not rig with line as I'm concerned this may be a visual distraction - personal preference of course.  Next up will be to attach the rudder chains which, nicely, are provided in the kit.
 

 

Thanks all for the nice words, likes and continued interest.  Know its been a while, seems as if I hit some sort of 'modelers wall'.  Before I can really continue with the topsides, I needed to turn my attention to mounting the rudder.  This is something I've been putting off for quite a while, and proved to be a very frustrating experience.  I had initially delayed doing this to allow the copper to oxidize as much as possible just in case of any errant CA glue and prevent shiny spots.
 
The kit provides PE rudder and pintle straps, but for some reason I couldn't get comfortable with them.  On Snake, the staps come with holes and pins were inserted, but this was something that in retrospect look a little too clunky and out of scale.  Looking at pictures of period ships, the bolts/nails are quite a subtle feature similar to treenails in visibility.  I experimented with card and styrene strip  to make these from scratch, but in the end decided to go with the supplied PE parts.  I forgot to take a picture, but instead of premade holes, these have rather large circular indentations in them, I'm guessing to simulate the bolts.  To my eye they looked to far apart, and the holes too big.  I made a slight alteration to increase the number of bolts/nail heads by drilling additional indentations to simulate what was already there.  The rudder straps also needed to be shortened quite considerably to eliminate overhang at the rear of the rudder.  These were painted with "Admiralty copper" paint after experimenting with other similar Tamiya colours.
 
The main challenge I found was to attach these without marring the copper plates, and this proved to be quite the challenge as at first the CA glue wouldn't provide a good bond and needed to be reapplied.  Scratching the hull plates and inside surface of the PE seemed to get things strong enough. The rudder proved quite the challenge to mount as this had been made with a low (for me) level of tolerance following the AOTS plans which is documented earlier in the log.
 
Interestingly, the box artwork shows a spectacle plate, but there is nothing in the kit nor instructions.  This was simulated using painted card and eyebolts, but interestingly there is very little room for this, however this seems consistent with AOTS diagrams.  The ironwork on the lower counter ports used some PE parts from the "Badger" set which I had bought a number of years ago.  These looked a little more in keeping scale wise than what is provide in this kit.  I may add ring bolts and rings to these, but will likely not rig with line as I'm concerned this may be a visual distraction - personal preference of course.  Next up will be to attach the rudder chains which, nicely, are provided in the kit.
 

 

Thanks all for the nice words, likes and continued interest.  Know its been a while, seems as if I hit some sort of 'modelers wall'.  Before I can really continue with the topsides, I needed to turn my attention to mounting the rudder.  This is something I've been putting off for quite a while, and proved to be a very frustrating experience.  I had initially delayed doing this to allow the copper to oxidize as much as possible just in case of any errant CA glue and prevent shiny spots.
 
The kit provides PE rudder and pintle straps, but for some reason I couldn't get comfortable with them.  On Snake, the staps come with holes and pins were inserted, but this was something that in retrospect look a little too clunky and out of scale.  Looking at pictures of period ships, the bolts/nails are quite a subtle feature similar to treenails in visibility.  I experimented with card and styrene strip  to make these from scratch, but in the end decided to go with the supplied PE parts.  I forgot to take a picture, but instead of premade holes, these have rather large circular indentations in them, I'm guessing to simulate the bolts.  To my eye they looked to far apart, and the holes too big.  I made a slight alteration to increase the number of bolts/nail heads by drilling additional indentations to simulate what was already there.  The rudder straps also needed to be shortened quite considerably to eliminate overhang at the rear of the rudder.  These were painted with "Admiralty copper" paint after experimenting with other similar Tamiya colours.
 
The main challenge I found was to attach these without marring the copper plates, and this proved to be quite the challenge as at first the CA glue wouldn't provide a good bond and needed to be reapplied.  Scratching the hull plates and inside surface of the PE seemed to get things strong enough. The rudder proved quite the challenge to mount as this had been made with a low (for me) level of tolerance following the AOTS plans which is documented earlier in the log.
 
Interestingly, the box artwork shows a spectacle plate, but there is nothing in the kit nor instructions.  This was simulated using painted card and eyebolts, but interestingly there is very little room for this, however this seems consistent with AOTS diagrams.  The ironwork on the lower counter ports used some PE parts from the "Badger" set which I had bought a number of years ago.  These looked a little more in keeping scale wise than what is provide in this kit.  I may add ring bolts and rings to these, but will likely not rig with line as I'm concerned this may be a visual distraction - personal preference of course.  Next up will be to attach the rudder chains which, nicely, are provided in the kit.
 

 

Drafting underway...just an hour or two every now and again when my girls are watching something stupid on TV.   So I sit with them but have my laptop with me while I pretend to be just a little interested.

One seaslug launcher, not finished, but other things to be getting on with, and first time ever posting from my mancave with the tablet

Update :
 
mounted the quarter deck stairs with handrails and rail-posts and connected to the balustrade...
 
Nils
 

 
 

 
 

Small Update :
 
shaped the main mast bits, made the anchor posts and a containment box for the spill spars, also rigged the anchors
 
Nils
 

 
 

 
 

 
 

Hello - further steps forward.
 
Thanks Blue Ensign for looking in and thanks for your good ideas 
 
Ships boat done (metal hull supplied with upgrade kit). A strip was added along sides for wale and painted black.
 

 

 

 

 
Yards are also all done as per plans.

 
Slight modification to fixing. Used tape banded around yards (painted yellow) with parts from upgrade kit for the Stunsail Boom

 
It's good to see more Fly builds on here.
 
Regards
 
Doug
 
 

That's my version for the sling of the main yards.
I used for the eye a custom made 5mm deadeye.
Thanks.
 
Stergios 
 
PS: The loop is passed the wrong way, I'll fix it later.

Not a huge amount to report as I was away in Belgium last weekend and have been busy at work during the week. 
 
Still working on smoothing the hull and now trying to remove the join between the plastic bow and wooden hull planking.

Very nice start on 'Cheerful'.  I like your heat bending setup!

Well I've decided on a finish.
 
As I've stated I'm looking at a more "older look" (without weathering etc.) something along the lines that the Russian builders accomplish. Something with some depth of color.
 
I tried about ten different types of finishes from tung oil (various number of coats) to sepia washes, wipe on poly etc. The tung oil left it to "orangey" with the cherry wood. So I had to get something to take that edge off.
 
I've decided upon a 50/50 coat of MiniWax Golden Oak brushed on and allowed to dry naturaly. I'll buff it out in 24 hours to take up any surface oil. It may darken or natuarlly patine on it's own and that would be fine.
 
Thank's to Ben and Chris for their input
 
Sam

Now you say that, it makes perfect sense...
 
A little more progress to show. I've been working on the transom again... I soaked the transom in boiling water and bent it round a frying pan (with vertical sides), and clamped it. That's resulted in a pleasing curve. I also started working on the side galleries.
 


Looking at those photos, I'm not sure with the way it curves upwards, so a rework is called for. But I'm pleased with where they end up w.r.t. the gunports and the transom.
 
For a little light relief, I've done some more work on the gratings, surrounding them with 2x6mm boxwood, and using a stock pot with sand paper inside to sand the curved profile on the top.
 


Happy building
 
Rob

Very nice start on 'Cheerful'.  I like your heat bending setup!

Lovely work Jesse, seems like I've missed a fair amount of progress.  Love the way the hammock nettings turned out.

Looks great Mark, nice to see some progress again.  Looks to be lots of interesting (i.e. challenging) angles at the bow there.

Thank you NMBrook, it is nice to see you again back on the forum.
Rest of yards is completed with all blocks and prepared for installation.

Update :
 
the place on deck is becoming scarce and I wanted to fit two elm-tree pumps (bilge water up and out )....
so the decision was to fit two tubes down through the decks but to fit a common double pump on it. The outlet chanels are still missing.
Further the port side anchor cableis rigged to the spill and the preliminary bit timbers at the foremast....   The boat rests above the spill on the two cradle racks and anchor cables
 
Nils
 

 
 

 
 

 

 

 
 
 
 
 
 

Thanks Mike and Dave, and belated New year greetings to yourselves. 
Post 6
That fairing business
Not done much work in the Shipyard since before Christmas, lacking some enthusiasm most probably because one of my least favourite aspects of a build is now required. Fairing seems to go on forever, and there is always the worry in the back of my mind that I may overdo it, and end up having to shim the bulkheads.

4024
One needs a good supply of sanding sticks for this task and I've added to my supply a curved stick made from a strip of Yellow pine left over from a much earlier scratch build of a twelve gun Brig, put into ordinary for many years and then abandoned due to terminal wood worm.
The wood comes off pretty easily during the bevelling operation, but the devil is as always in the detail of the process.

4469
I made a simple block jig to support the inverted hull whilst working.

4467
Once I reached the point where I felt there was a smoothish transition a walnut batten was pinned along the hull at gunport cill level.

4474
getting there I think, at least on the starboard side.

4470

4472

4462

4473
The fairing continues, a further batten strip will be added at Wale level, and a third lower down.
 
B.E.