hof00 Posted August 5, 2019 Author #61 Posted August 5, 2019 Hi Chap, The "Hard" Solder doesn't come with a Flux Core. Have to put the Flux on separately. Strengthened the outside of the Firewall .with "Shim" Brass and Planking Nails, the Fuselage Longeroons need a bit of a solid penetration through the afore mentioned Firewall. I'm still have reservations regarding accurate measurements, I have already had to move the last Cockpit Frames 10mm aft.... (Solder is good here.... 😊) (I also tried some "Supposedly" really great Polymer resin for Brass/Muntz metal joints, not good. (Even Brass/Wood not good.... ☹️) Anyway, onwards and upwards? Cheers....HOF. Canute, popeye the sailor and mtaylor 3 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
cog Posted August 5, 2019 #62 Posted August 5, 2019 Would CA do the job instead of the polymer? popeye the sailor and Canute 2 Quote Carl "Desperate affairs require desperate measures." Lord Nelson Search and you might find a log ...
hof00 Posted August 6, 2019 Author #63 Posted August 6, 2019 (edited) Hi Chap, CA would probably be o.k. but need something a little more "Shock" Proof._ (My "Super T" CA is past it's best by date.... Guess I have to order some?) The Polymer is touted, "Stronger than Superglue," I don't think so.... Cheers….HOF. Edited August 9, 2019 by hof00 mtaylor and popeye the sailor 2 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
Canute Posted August 8, 2019 #64 Posted August 8, 2019 There are rubber filled CAs available. Helps reduce the shearing issues of CA. popeye the sailor, mtaylor and cog 3 Quote Ken Started: MS Bounty Longboat, On Hold: Heinkel USS Choctaw paper Down the road: Shipyard HMC Alert 1/96 paper, Mamoli Constitution Cross, MS USN Picket Boat #1 Scratchbuild: Echo Cross Section Member Nautical Research Guild
hof00 Posted August 9, 2019 Author #65 Posted August 9, 2019 (edited) Thanks Chap, Awaiting some "ZAP" products, CA and Epoxy. Supposedly delivered this morning but I think the Courier may be Dyslexic? (Casting no aspersions but had this in the past...) Anyway, while I chase this up with the supplier, have primed the Cowling/Careening/Axle Wheel parts in preparation for the "Red." So, hoping for some sort of miracle delivery this weekend, it'll probably be next week before I can get anything else done.☹️ Have a good weekend all!! Cheers....HOF. Edited August 9, 2019 by hof00 popeye the sailor, mtaylor, Cabbie and 2 others 5 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
hof00 Posted August 9, 2019 Author #66 Posted August 9, 2019 (edited) Oops, forgot, Work on the Firewall continues as does the Cockpit Veneer stuff, I have plenty of stuff to do.... Cheers....HOF. Edited August 9, 2019 by hof00 popeye the sailor, mtaylor and Canute 3 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
cog Posted August 9, 2019 #67 Posted August 9, 2019 Most couriers are ... or plain lazy Enjoy the weekend. mtaylor, popeye the sailor and Canute 3 Quote Carl "Desperate affairs require desperate measures." Lord Nelson Search and you might find a log ...
Cabbie Posted August 14, 2019 #68 Posted August 14, 2019 On 8/8/2019 at 9:58 PM, Canute said: There are rubber filled CAs available. Helps reduce the shearing issues of CA. Hi Canute does the rubber filling make it a bit slower to dry and a bit thicker as glue. I cannot use ca, never sticks, all my fault definitely. I would like a slower and bit thicker clear glue. Can you show a pic of what you are talking about? thanks Chris Oh and Howdy Hof I hope you are managing to make some progress. 😉😁 mtaylor, Canute and popeye the sailor 3 Quote HM Cutter Mermaid 1817 HMB Endeavour 1768 by Cabbie - Artesania Latina - 1:60 - Kit Fiddle Every action has a consequence
mtaylor Posted August 14, 2019 #69 Posted August 14, 2019 Cabbie, What thickness of CA are you using? My hobby shop carries "super thin", "thin", "regular/medum" and something called "cap-filling" and there is a "thick". Try the "cap-filling" or one of the slow-curing CA's. popeye the sailor and Canute 2 Quote Mark "The shipwright is slow, but the wood is patient." - me Current Build: Past Builds: La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD Triton Cross-Section NRG Hallf Hull Planking Kit HMS Sphinx 1775 - Vanguard Models - 1:64 Non-Ship Model: On hold, maybe forever: CH-53 Sikorsky - 1:48 - Revell - Completed Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)
cog Posted August 14, 2019 #70 Posted August 14, 2019 (edited) Cabbie The thicker CA gets, the slower it cures, still faster than most glues. The super thin just a few seconds, the gell like which can take up to half a minute/minute I use Insta-cure from BSI the blue insta-cure takes 3 secs, the thicker insta-cure+ takes on average 15 secs there is an ever thicker one which will probably take a minute or so. If you use a different brand, it will have different curing times for their respective thicknesses Edited August 14, 2019 by cog Canute, popeye the sailor, mtaylor and 1 other 4 Quote Carl "Desperate affairs require desperate measures." Lord Nelson Search and you might find a log ...
Canute Posted August 15, 2019 #71 Posted August 15, 2019 Cabbie, here's one brand from Loctite: https://www.loctiteproducts.com/en/products/fix/super-glue/loctite_super_glueultragelcontrol.html mtaylor, popeye the sailor and cog 3 Quote Ken Started: MS Bounty Longboat, On Hold: Heinkel USS Choctaw paper Down the road: Shipyard HMC Alert 1/96 paper, Mamoli Constitution Cross, MS USN Picket Boat #1 Scratchbuild: Echo Cross Section Member Nautical Research Guild
hof00 Posted August 16, 2019 Author #72 Posted August 16, 2019 Hi All, I'll wade in to the debate.... Finally got my "ZAP" stuff.... Thin CA and 15 Minute Zpoxy. I have used the CA to "Pin" the Metal where appropriate and the Zpoxy to strengthen the joint. (I rate the Zpoxy!! There is also a 5 minute version available) The stuff I used before giving it a miss was a commercial product by "Selleys" called Power Grip, it was anything but.... Maybe I wasn't patient enough? Anyway, work continues on the DR1, lots of metal bits, not so much wood.... (I didn't enjoy Metalwork in my first year of High School, that's why I reverted to Home Economics, Cooking.... 🙂) (I retained the Woodwork though.) Once the Elevators are complete, (Tomorrow?), I'll post some photos. Have a great weekend!! Cheers....HOF. cog, Canute, Edwardkenway and 3 others 6 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
Cabbie Posted August 17, 2019 #73 Posted August 17, 2019 Thanks all Mark, To me so far super glue is super glue, just been getting the standard one but now i see that there all sorts. Thanks Cog that looks like the one for me and i can get it in Aus from here https://www.modelflight.com.au/bob-smith-industries-insta-cure-plus-gap-filling-cyanoacrylate-2-oz-glue.html Thanks Canute yours is instant which i don't know if i can handle, instant types are what I have been using. Hi Hof looking forward to seeing more of your work. Epoxy glues seem to be messy with me. I will give the BSI one a go. First I need to make some time and do some modelling. I did come across this video, I think it is CA with an accelerator, imagine the mess i could have with that stuff. Cheers Chris https://www.facebook.com/watch/?v=2263190990446441 mtaylor, cog, Canute and 1 other 4 Quote HM Cutter Mermaid 1817 HMB Endeavour 1768 by Cabbie - Artesania Latina - 1:60 - Kit Fiddle Every action has a consequence
cog Posted August 17, 2019 #74 Posted August 17, 2019 Cabbie, BSI has an accelerator too, so if you want to have some fun ... nothing to stop you Cabbie, popeye the sailor, mtaylor and 1 other 4 Quote Carl "Desperate affairs require desperate measures." Lord Nelson Search and you might find a log ...
hof00 Posted August 18, 2019 Author #75 Posted August 18, 2019 Hi Chris, Et all, Agree, Epoxy can be slippery and messy, not so nice to work with.... CA has it's uses, the late great Manstini called Super Glue "Stupid" Glue. (Ship Modelling Simplified.) Anyway, work continues on the Elevator/s, not by any means finished this. Aligning Ribs with the Tail plane and then clean up the Epoxy Fillets, I will no doubt need a touch up or two during this process. With the Z-Poxy, the stuff goes solid, commercial Epoxy, (Araldite), seem to stay "Plastic" for days.... (At 3.4"C tonight, (OS temperature), it's taking a little more than 15 minutes to go off, plenty of time for fine adjustment. 🙂) Cheers....HOF. Canute, Cabbie, cog and 2 others 5 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
hof00 Posted August 18, 2019 Author #76 Posted August 18, 2019 Temperature is dropping in Stokes Vegas.... 2.1"C Plastered the corners of the Firewall with Z-Poxy. Hopefully this will complete integrity of this rather brittle component and the penetration's therein. 🙂 Already tidying up the Elevator/Tail Plane, more Z-Popxy Fillets.... (I may have to spray the Control surfaces Gunmetal/Silver, we'll see....) Carl, I promise to post some photos later today, just for you Chap. 🙂 Cheers....HOF. Cabbie, Canute, mtaylor and 1 other 4 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
Canute Posted August 19, 2019 #77 Posted August 19, 2019 Loctite make a glue titled Power Flex. Has a black label (because of the rubber?) Per my source, it's a gel. So you'll get a little working time. I myself will be looking for some of this stuff after my current supply gets used up or solidifies. mtaylor, Cabbie and popeye the sailor 3 Quote Ken Started: MS Bounty Longboat, On Hold: Heinkel USS Choctaw paper Down the road: Shipyard HMC Alert 1/96 paper, Mamoli Constitution Cross, MS USN Picket Boat #1 Scratchbuild: Echo Cross Section Member Nautical Research Guild
hof00 Posted August 20, 2019 Author #78 Posted August 20, 2019 (edited) Updates: Apologies that these are late.... Had issues with the Tail Plane/Elevators.... Trying to clean these up last night, the Port side LE separated, glued it back on but the Geometry changed slightly which meant the Elevator did not have clearance to operate. Replaced the LE, Epoxy Fillets and cleaned up a bit. (Might give it a bit more of a "Tickle" tomorrow.) Anyway.... Edited August 20, 2019 by hof00 Landrotten Highlander, Canute, GrandpaPhil and 3 others 6 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
hof00 Posted August 20, 2019 Author #79 Posted August 20, 2019 Rudder Re-Engineered: popeye the sailor, Landrotten Highlander, Canute and 3 others 6 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
hof00 Posted August 20, 2019 Author #80 Posted August 20, 2019 Firewall undergoing strengthening: GrandpaPhil, mtaylor, cog and 3 others 6 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
hof00 Posted August 20, 2019 Author #81 Posted August 20, 2019 (edited) Cowling, Careening, (Don't know why it's called that), and Wheels: Edited August 20, 2019 by hof00 GrandpaPhil, cog, Landrotten Highlander and 3 others 6 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
hof00 Posted August 20, 2019 Author #82 Posted August 20, 2019 (edited) A couple of pictures of "Sausage" 1 and 2 after a couple of hard days "Helping" with Modelling activities and other Cat Stuff.... Edited August 20, 2019 by hof00 CDW, popeye the sailor, mtaylor and 6 others 9 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
hof00 Posted August 20, 2019 Author #83 Posted August 20, 2019 Addendum: I did try to Hard Solder the Rudder/Tail Plane/Elevator components. It's o.k. for the Brass/Brass connections but not for Brass/Muntz Metal stuff, I did try.... (I also researched on the Net.) Seemed to be too much risk associated with high, (Blow Torch), temperatures/melting points. Z-Poxy seems to have done the trick. Firewall stuff later today perhaps.... Cheers....HOF. cog, popeye the sailor, mtaylor and 1 other 4 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
popeye the sailor Posted August 20, 2019 #84 Posted August 20, 2019 very nice progress HOF Canute and mtaylor 2 Quote I yam wot I yam! finished builds: Billings Nordkap 476 / Billings Cux 87 / Billings Mary Ann / Billings AmericA - reissue Billings Regina - bashed into the Susan A / Andrea Gail 1:20 - semi scratch w/ Billing instructions M&M Fun Ship - semi scratch build / Gundalow - scratch build / Jeanne D'Arc - Heller Phylly C & Denny-Zen - the Lobsie twins - bashed & semi scratch dual build Billing T78 Norden in dry dock: Billing's Gothenborg 1:100 / Billing's Boulogne Etaples 1:20 Billing's Half Moon 1:40 - some scratch required Revell U.S.S. United States 1:96 - plastic/ wood modified / Academy Titanic 1:400 Trawler Syborn - semi scratch / Holiday Harbor dual build - semi scratch
lmagna Posted August 21, 2019 #85 Posted August 21, 2019 (edited) Has anyone tried this stuff: https://www.vms-supplies.com/flexy-5k-pe-product-overview According to stuff I have read and at least one video that is out there somewhere, it appears that this stuff is both stronger by a considerable margin and flexible as well. It appears that it comes in a number of thicknesses and setting times. The only real place I have seen it sold here in the US is through eBay and is shipped directly from Poland. I bought one bottle so far for use on my Houston build when I can get to it. It has a multi piece hull made of resin and I wanted to make certain the bond was extremely strong. I have not opened it yet as I have not started the Houston build and don't want it going bad after opening. They also seem to carry a bunch of other products for weathering, texturing, painting, and so forth. Edited August 21, 2019 by lmagna Canute, mtaylor and popeye the sailor 3 Quote Lou Build logs: Colonial sloop Providence 1/48th scale kit bashed from AL Independence Currant builds: Constructo Brigantine Sentinel (Union) (On hold) Minicraft 1/350 Titanic (For the Admiral) 1/350 Heavy Cruiser USS Houston (Resin) Currant research/scratchbuild: Schooner USS Lanikai/Hermes Non ship build log: 1/35th UH-1H Huey
hof00 Posted August 21, 2019 Author #86 Posted August 21, 2019 (edited) Thanks Dennis/Lou, Progress with the Firewall, It's a bit of a mission.... There are "Veneers" that attach and a whole host of other stuff. Thinking about some "Mods" to make stuff more accurate/secure. As stated, some time ago, this Model/Kit leaves a lot to be desired. (I'll try my level best to complete....) Cheers....HOF. Edited August 21, 2019 by hof00 mtaylor, Canute and popeye the sailor 3 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
hof00 Posted August 29, 2019 Author #87 Posted August 29, 2019 Small update.... Work continues on the Fuselage.... I'm not too happy with it, there are no accurate measurements in the "Destructions" it's just go with the flow and try to get things lined up/square. As stated before, there are many, many issues.... One of the se is the fragility of the components, Esp, the "Muntz" ones. (Filed a bit of a groove tonight for the Instrument Cluster, it just fell to bits with the most gentle touch, anyway, rebuilt/fixed with CA/Epoxy.) I think that this one has been languishing too long and over time, if not assembled, the parts degrade. Haver completed the Control Column, Rudder Bar, Cockpit Floor and am reasonably happy with the Firewall and "Cockpit" Veneers. I have also to fabricate some Lugs for the Landing Gear/Interplane Struts as the most forward Cockpit Frames were missing and I had to Fabricate these also. So, we'll see how it goes.... I'll post some photos tomorrow. Cheers....HOF. lmagna, Cabbie, mtaylor and 3 others 6 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
cog Posted August 29, 2019 #88 Posted August 29, 2019 Hang in there 'arry, you are doing rather well for what you have to work with ... Old Collingwood, lmagna, popeye the sailor and 2 others 5 Quote Carl "Desperate affairs require desperate measures." Lord Nelson Search and you might find a log ...
mtaylor Posted August 30, 2019 #89 Posted August 30, 2019 Is this "Muntz" metal copper colored? If it is, it's the "good stuff" that was used in last period of the wooden sailing ships as it was cheaper than pure copper (it's a copper alloy). If it's a silver color, heaven knows what it but my dad and others always called it "pot metal" which was because they just tossed stuff in to the mix. Very fragile and deteriorates (usually) over long periods of time. cog, popeye the sailor and Canute 3 Quote Mark "The shipwright is slow, but the wood is patient." - me Current Build: Past Builds: La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD Triton Cross-Section NRG Hallf Hull Planking Kit HMS Sphinx 1775 - Vanguard Models - 1:64 Non-Ship Model: On hold, maybe forever: CH-53 Sikorsky - 1:48 - Revell - Completed Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)
hof00 Posted August 30, 2019 Author #90 Posted August 30, 2019 (edited) Thanks Carl/Mark, Wot I call "Muntz_ is called "Minatz" or similar in the instructions. (White Metal.) (I call it Muntz as that is what I have called it before.... It's horrible stuff.)) Anyway, a couple of photos.... Have an awesome weekend!! Edited August 30, 2019 by hof00 lmagna, GrandpaPhil, mtaylor and 5 others 8 Quote Completed Builds: A/L Bluenose II A/L Mare Nostrum Sergal/Mantua Cutty Sark A/L Pen Duick A/L Fulgaro Amati/Partworks 1/200 Bismarck A/L Sanson
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.