Blue Ensign

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Good move Chris,

The one in the centre is apparently Nelson's sword found in his cabin after Trafalgar.
The ones right and left are the surrendered French and Spanish swords.
 
Cheers,
 
B.E.
 

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Good move Chris,

The one in the centre is apparently Nelson's sword found in his cabin after Trafalgar.
The ones right and left are the surrendered French and Spanish swords.
 
Cheers,
 
B.E.
 

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Post One Hundred and Seventy-two
Sphinx and ‘Indy’
I thought members may be interested to see the comparison between Chris’s two premier kits, Sphinx and Indefatigable.
They sort of represent the alpha to omega of British frigates.
Sphinx, the bijou 9 pounder vessel, and ‘Indy’, the pocket battleship of her day, carrying 24 pounders supplemented with 42 pounder carronades.
I recall that when I built Sphinx I thought she was quite large, when ‘Indy’ arrived I thought I’m going to need a bigger bench!

04505

04506

04507

04508

04512

05413

05414

04517
If a large statement model is required ‘Indy’ is a good choice, but if masted and fully rigged she will take up a lot of room.
Built Navy Board style she is still a heavy model and a glass case even with reduced height and width adds considerably to the weight.
Sphinx is certainly of a size more amenable to a domestic setting; a pretty little frigate that appeals to my deeper affection for the more decorative vessels of the 18thc. before austerity took over as the expensive Napoleonic wars ground on.
 
Indefatigable sort of spans this period, all black and yellow, no decorative topsides, but the stern gallery still looks good to my eye. She is modelled with an open Fo’csle before her bulwarks were built up, and she does have a magnificent Figure at her head.
 
I am more than happy to have both in my collection.
 
 
Thank you, Chris, for providing me with an engrossing thirteen months of work. It is a tribute to your designs, to be able to build a model of this quality and detail in such a short time.
 
Thanks are also due to James, for producing the prototype ‘Indy’ build which provided a very useful reference guide.
 
B.E.
02/05/2024

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Good move Chris,

The one in the centre is apparently Nelson's sword found in his cabin after Trafalgar.
The ones right and left are the surrendered French and Spanish swords.
 
Cheers,
 
B.E.
 

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

The detail looks amazing Chris, but I'm intrigued by the style of the sword.
 
It does not  resemble any Naval sword I recall seeing, was it perhaps a specific sword gifted to Nelson?
It rather looks like the sword on the Nelson statue atop his column.
 
The Nelson Companion edited by Colin White has a photo of the only sword that is known to have been owned by Nelson, and it is of the traditional type.
 
For the purposes of displaying the figure on a model I think it would be safer to include a Naval pattern sword.
 
Just a thought.
 
B.E.

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Post One Hundred and Seventy-two
Sphinx and ‘Indy’
I thought members may be interested to see the comparison between Chris’s two premier kits, Sphinx and Indefatigable.
They sort of represent the alpha to omega of British frigates.
Sphinx, the bijou 9 pounder vessel, and ‘Indy’, the pocket battleship of her day, carrying 24 pounders supplemented with 42 pounder carronades.
I recall that when I built Sphinx I thought she was quite large, when ‘Indy’ arrived I thought I’m going to need a bigger bench!

04505

04506

04507

04508

04512

05413

05414

04517
If a large statement model is required ‘Indy’ is a good choice, but if masted and fully rigged she will take up a lot of room.
Built Navy Board style she is still a heavy model and a glass case even with reduced height and width adds considerably to the weight.
Sphinx is certainly of a size more amenable to a domestic setting; a pretty little frigate that appeals to my deeper affection for the more decorative vessels of the 18thc. before austerity took over as the expensive Napoleonic wars ground on.
 
Indefatigable sort of spans this period, all black and yellow, no decorative topsides, but the stern gallery still looks good to my eye. She is modelled with an open Fo’csle before her bulwarks were built up, and she does have a magnificent Figure at her head.
 
I am more than happy to have both in my collection.
 
 
Thank you, Chris, for providing me with an engrossing thirteen months of work. It is a tribute to your designs, to be able to build a model of this quality and detail in such a short time.
 
Thanks are also due to James, for producing the prototype ‘Indy’ build which provided a very useful reference guide.
 
B.E.
02/05/2024

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Good move Chris,

The one in the centre is apparently Nelson's sword found in his cabin after Trafalgar.
The ones right and left are the surrendered French and Spanish swords.
 
Cheers,
 
B.E.
 

The detail looks amazing Chris, but I'm intrigued by the style of the sword.
 
It does not  resemble any Naval sword I recall seeing, was it perhaps a specific sword gifted to Nelson?
It rather looks like the sword on the Nelson statue atop his column.
 
The Nelson Companion edited by Colin White has a photo of the only sword that is known to have been owned by Nelson, and it is of the traditional type.
 
For the purposes of displaying the figure on a model I think it would be safer to include a Naval pattern sword.
 
Just a thought.
 
B.E.

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Good move Chris,

The one in the centre is apparently Nelson's sword found in his cabin after Trafalgar.
The ones right and left are the surrendered French and Spanish swords.
 
Cheers,
 
B.E.
 

The detail looks amazing Chris, but I'm intrigued by the style of the sword.
 
It does not  resemble any Naval sword I recall seeing, was it perhaps a specific sword gifted to Nelson?
It rather looks like the sword on the Nelson statue atop his column.
 
The Nelson Companion edited by Colin White has a photo of the only sword that is known to have been owned by Nelson, and it is of the traditional type.
 
For the purposes of displaying the figure on a model I think it would be safer to include a Naval pattern sword.
 
Just a thought.
 
B.E.

Post One Hundred and Seventy-two
Sphinx and ‘Indy’
I thought members may be interested to see the comparison between Chris’s two premier kits, Sphinx and Indefatigable.
They sort of represent the alpha to omega of British frigates.
Sphinx, the bijou 9 pounder vessel, and ‘Indy’, the pocket battleship of her day, carrying 24 pounders supplemented with 42 pounder carronades.
I recall that when I built Sphinx I thought she was quite large, when ‘Indy’ arrived I thought I’m going to need a bigger bench!

04505

04506

04507

04508

04512

05413

05414

04517
If a large statement model is required ‘Indy’ is a good choice, but if masted and fully rigged she will take up a lot of room.
Built Navy Board style she is still a heavy model and a glass case even with reduced height and width adds considerably to the weight.
Sphinx is certainly of a size more amenable to a domestic setting; a pretty little frigate that appeals to my deeper affection for the more decorative vessels of the 18thc. before austerity took over as the expensive Napoleonic wars ground on.
 
Indefatigable sort of spans this period, all black and yellow, no decorative topsides, but the stern gallery still looks good to my eye. She is modelled with an open Fo’csle before her bulwarks were built up, and she does have a magnificent Figure at her head.
 
I am more than happy to have both in my collection.
 
 
Thank you, Chris, for providing me with an engrossing thirteen months of work. It is a tribute to your designs, to be able to build a model of this quality and detail in such a short time.
 
Thanks are also due to James, for producing the prototype ‘Indy’ build which provided a very useful reference guide.
 
B.E.
02/05/2024

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024

Post One Hundred and Seventy-three
 
18’ cutter – Jolly Boat
 
I thought I would have another stab at clinker planking one of these bijou cutters to go with 'Indy'.
 
My original cutter which sits with Alert was of the older version replaced shortly after I had completed it.
This one is the current and revised version, which includes laser cut gratings and footwalings whereas the original had brass etch versions.
 
I will be using 3.4mm x 0.6mm Boxwood strip, and of necessity the planking starts at the keel and works up to the Wash strake.

4315
The Garboard is applied first using pva. This is shaped at the bow but is otherwise untapered.

4320
The second strake overlaps the Garboard by 1mm.
In proper practice there is a rebate or rabbet edge along the top of each plank to take the bottom edge of the plank above.
At scale and with 0.6mm board I can dispense with this nicety.
 
From the second plank above the Garboard I am adding a degree of taper both fore and aft. How much is down to eye and best guesstimate.
4528
As with all these projects clamping is an issue, more so as the planking rises.

4531
With three strakes added I move to the wash strake. This is fitted untapered into the bow slot.
 
Twice the stem part broke but repair was effected and once the wash strakes are in place the area is more stable.

4542
As the strakes are applied the taper increases fore and aft until the final strake fits flush with the lower edge of the wash strake.

4552

4550
Planking completed in its raw state, but the lapstrakes are clearly evident.

4565
I applied a 1mm square Ebony strip along the lower edge of the wash strake to represent the wale.
It looks broader than it is because top and face edges are not clearly defined on the photo.

4568

4569
There is a satisfaction to be had from completing the hull of this smallest of the boat range, but there is a fair bit of cleaning up required before the inboard fittings are put into place.
 
B.E.
 
06/05/2024