Cathead

Looking good.
 
I realize this is a somewhat minor point but the bottom sizing is done with the ends of the shrouds heading in opposite directions. See below picture below (note as I was using cable laid rope the direction is reversed from what you would do with your shrouds).

The next two seizing would be as you have done them. Also the way you tie them off is to pull the end through the gap and wrap around under so it holds it. Again see below picture.

You can't see it in the picture but the bottoms loop goes under the lanyard coming through the gap to secure everything.
 
None of this is necessary, but if you want to make it look a little more authentic these are some small adjustments you can make.

The first item of rigging is complete with the driver boom install. I rigged the boom with the mast off the hull which turned out to be a good idea.  During my first attempt at raising the boom I realized that the parrels would not slide above the lower mast cleats and the block for the main yard so I had to remove the block and retie the parrels.  With the boom in position, I wound up running the line the wrong way through a couple of blocks and had to pull the line back and rerun through the blocks in the correct orientation.  Redoing my work was much easier without the mast stepped. The sheets for the boom are hanging loose for now.
 

 

 
I did change my mind and decided to step the mast prior to installing the yards. With the mast seated I am now working on rigging the main shroud deadeyes. The results of my first attempt were dreadful so I did some quick research on rigging deadeyes. That led me to a picture of a deadeye rigging jig in a post in the Masts, Rigging and Sails forum by hornet (https://modelshipworld.com/uploads/monthly_01_2017/post-1505-0-68284800-1483318896.jpg).. I had the materials on hand and made one of my own. 
 

 
Using the jig to place the upper deadeye in to position, grabbing the shroud line with hemostats just above the deadeye and resting the handle base of the hemostat on the chain plate was a much easier approach.

 
The end result turned out much better than I had anticipated.

 
With the deadeye connected to the shroud I connected the two together in 0.5mm rope.  I'll clip the rope later.
 

 
The building sequence in the manual seems to show the shroud cleats installed after all the shrouds are connected. I think it may be easier to install the cleats after I finish connecting each shroud and am wondering if there are any drawback to using this sequence. 
 
 
 
 

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Hello, and many thanks for all the likes
because the vegetation here is 4 weeks in advance of normal years, my garden now needed much of my time. But today it rained and so I'm back at the shipyard.
 
The carpenters set in the deck beams and started with the paneling of the walls.



 

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Looks great Eric.
Brian, I use one of the magnetic squaring jigs when it's possible to build off the model.  When it's scratch I always use it.

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Looking good Eric. I may have to look into getting me one of those magnetic squaring jigs. Looks pretty handy. 
 
-Brian

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Eric, that looks so good, you're doing a swell job of replicating her. 

Nice job on the cabin, the build's really coming together well!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!

Well, I said I'd work on either the hog chains or the main cabin, and for once I stuck to the plan.
 
Building the rest of the cabin was mercifully straightforward, to the point that I didn't take many in-progress shots. I used some sheets of board-and-batten wood left over from past model railroad projects to lay out the walls, and scavenged close-enough windows from my scrap box. Here are the walls well underway, showing the bracing in the back and the carefully cut-and-fit holes for inserting the windows:

I painted everything white, then glassed in the windows the same way as the pilot house (CA plus scrap clear packaging), then added shades using some old sailcloth material from a past ship kit. When that was done, I assembled the structure using my magnetic squaring jig:
 

And here's the result:
 

Here's the cabin test-fit on the rest of the model, with relevant photos in the background:
 


It's been stressful around here lately and I needed a simple project that didn't require too much thought. This fit the bill perfectly. Doing the roof should be easy, too. Then I'll mark its location carefully and start laying out the hog chain braces.
 
Thanks as always for following along and giving feedback, whether through likes or comments. You all keep me going!