Jump to content
New Publication - Ship Modeler's Handbook - Temp out of stock ×

RGL

Members
 View Profile  See their activity

  • Posts

    5,309

  • Joined

  • Last visited

Everything posted by RGL

  1. RGL
    So to compare the 3D printed to the kit supplied (with some aftermarket)
  2. RGL
    Ok, final works, a blue filter a grey wash a white airbrush and a little bit of brass for the barrel ends
  3. RGL
    Quad secondary guns part 2. The armistice stripes then the base grey coats. I’ll leave these now for 24 hours then start on the filters.
  4. RGL
    She has some pretty good lines, so I’ve now cut in the plates. I’m going to oil can her below the waterline ( because I can really), the RN had a serious shortage of enamel for their paints and o it the boot strap was good quality as that was the highest exposure area at the waterline. I have to finish my last guns for the Strasbourg this week.
  5. RGL
    Hull lines in, I added a few more, a couple of coats of primer with a flea type can. Tomorrow I’ll etch in the plates and put the undercoats on to represent the ships base primer and metal coats with oil canning.
  6. RGL
    Should be good!
  7. RGL
    None of the aftermarket is for the HMS Kent so it’s not really linear, so I’m scratching around replacing doors and other stuff, metalled floor indeed the waist guns. I’m almost ready to start painting again.
  8. RGL
    Mike, I pre paint them then place them and add a drop of fast setting very thin CA . The only reason I didn’t do individual stanchions on this one is that they were actually hard metal ones instead of stanchion and wire.
  9. RGL
    Bridge basics done
  10. RGL
    I use brass rod for pipes, it comes in various sizes and is easy to bend unlike plastic which has a mind of it’s’ own.
  11. RGL
    All ships are money pits I thought
  12. RGL
    My plan is to do it same way I did with my fletcher just a bit bigger.
  13. RGL
    Doing up the main bridge area, the box art and the ship has splinter mattresses. None provided or available under $100 I’m going to use 5mm plastic strip, after I prime it I will scribe In the details
  14. RGL
    The kit provides a Poor plastic catapault for the seaplane so I scratch built one from bits and pieces
  15. RGL
    So this is the searchlight platform and will have quad vickers on them.
  16. RGL
    So today after 2 months the rear 3D printed guns arrived from NZ. I’m pretty sure it’s Australia Posts fault as anything coming through Melbourne hits a massive backlog due to the Covid’s
  17. RGL
    Nice, Pontos instructions generally assume a lot of your ability to mind read but it really is excellent. Good to see another coming to the dark side.
  18. RGL
    I find if the thin up the inner gunnel it will sit a little below the edge allowing the stick on deck to sit flush (if that makes sense). I don’t think I could fit a 1/200 beast!
  19. RGL
    Does the deck sit flush?
  20. RGL
    I look at all the IWM photos of the RN Ships from WW2, they have that fantastic black and white crispness I’d live to see in colour.
  21. RGL
    Thought I’d make a start, drill out the portholes, thin out the ledges for the deck so it sits just below the gunwhale, PE Foxsle added, funnels done
  22. RGL
    I have broken off that many masts repositioning my ships it beggars belief, as they are always already rigged and need CA and a quick set solution.
  23. RGL
    The Hull is quite nice but will need some work to make her look real. The camouflage pattern will be pretty dominant and therein lies the challenge of oil canning at different colours. The deck was also painted over so that’s going to need work as well. Most kits these days are starting to replace a lot of the finer details with their own PE, but this is no where as complex as the Fletcher or Spruance was to build.
  24. RGL
    Yes, I’m always a bit sceptical given he misses the metal focsle which Trumpy misses too.
  25. RGL
    And a set of plans

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...