-
Posts
3,498 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by captainbob
-
You should be proud of a boat well built. Congratulations !
- 296 replies
-
- herreshoff
- buzzards bay
-
(and 1 more)
Tagged with:
-
Tom, Thanks for your concern that I get this right. What you say is true for some boats and I was going to rig the Lettie that way until I read Chapelle’s book. He tells how boat rigging changed with size and year. The attached drawings may explain what I am doing and why the question. With the blocks shown there are six lines and the port side fall has a block attached as a becket. This becomes part of the Jig shown in the other sketch. The drawings were taken from two different parts of the book. I will take the main throat halyard to the starboard side and the jig halyard to the port. The fore sail being smaller and not as heavy will not need the jig and it will be gigged the way you describe. Bob
-
Jud and Nils, thanks for joining in. Tom, when sailing smaller boats I would hang coils on cleats in the same way you described but that seem like an awfully big coil to hang. Thanks for the answer. SpyGlass, as it turns out the halyard was, as you say, “double tailed”. But the other end went to a set of blocks and was called the halyard jig. The halyard was used to lift the sail and the halyard jig was used to tighten by lifting that last little bit. Bob
-
I’m getting closer to figuring out where all the blocks, fittings and belaying pin need to be so the schooner can be rigged. Most models I see use the same five or six rounds of line to make up the hanks of rope for each belaying pin but that is not correct. Last night as I was studying the main throat and peak halyards, the engineer in me took over and I suddenly realized just how much rope is required. If the distance between the lowered gaff and the raised gaff is 30 feet and you have, as Chapelle shows, two double blocks at the crosstree and a double and single block on the gaff jaws, that’s a total of six lines going up and down. At 30 feet each that’s 180 feet of rope. When the sail is raised and the halyard is belayed the remaining line is made into a hank. If the hank is 2 1/2 feet top to bottom or 5 feet around that is 36 turns of rope. That is too much line for one pin but I have never seen on any of the pin diagrams that more than one pin was used. So what did they do with all the excess rope? Bob
-
Harriet McGregor by Boccherini
captainbob replied to Boccherini's topic in - Build logs for subjects built 1851 - 1900
Beautiful. Bob -
Thanks Nils but I don’t think the brass comes close to yours. It's all in the camera. Thanks Pete I was starting to work on wood hoops when I remembered the admiral said black and gold so the hoops are now slices of brass tubing and the pins may be brass also. Bob
- 420 replies
-
I'll wait to see what color you choose. But it looks like you're going to have to build a boat shed / show room to store this cutter and Maria. Bob
- 2,207 replies
-
WOW ! Put a glass top on it and you have a table. Bob
- 2,207 replies
-
I couldn't have said it better myself. "a pure joy". Bob
- 170 replies
-
- ogallala
- praire schooner
-
(and 2 more)
Tagged with:
-
Thanks Russ that makes sense. I haven’t seen the turnbuckle yet but I’ll keep looking. Bob
- 420 replies
-
Thanks Russ, Michael and Carl. Please forgive my ranting Chapelle's book really is good. John, they are not straps they are a long "U" shaped rods. It goes down one side, around the mast and up the other side, and they pivot from a pin going through the mast top. The long one on the fore mast supports the jumbo jib stay (the innermost of the three jibs). The short "U" on the back of the foremast has a line going to the long "U" on the main mast. That line is called the spring line. That's as much as I know. Bob
- 420 replies
-
Well it’s been a month since I entered any pictures and on the one hand I’m sorry to have so little to show, on the other hand, when the HAER got the Lettie for documentaion the masts had been stripped and removed, so there are no rigging diagrams for her. So I have had the fun of trying to decipher the information in Chappelle’s book, “The American Fishing Schooner”. It’s a lot of, which one of the many ways to rig the bow sprit do I use? Big boat or small, this year or that and then is it like this boat or that. There is no index for the second half of the book, it is supposedly in alphabetical order. So you look at the drawing of the fife rail and there is information about the mast that is not shown anywhere else. So after going through it time and time again I made my own table of contents. Anyway enough of that. Before I could do the masts and spars I had to figure out how many blocks of what size and where mounted and do I use just the haulyard or do I use the haulyard jig also. I have come up with a diagram in my head that I will use, hopefully it will not have to change too many times. So here is the start, the masts. I’m open to any comments, when it comes to rigging I‘m definitely not an expert. Bob Main mast Fore mast
- 420 replies
-
Love that first picture, up through the frames, of the below decks area. You always do such great work. Bob
-
Come on Pete. With all the small and mini RC equipment out there. Surely you can find some that will fit. Go for it. Bob
- 296 replies
-
- herreshoff
- buzzards bay
-
(and 1 more)
Tagged with:
-
She's really coming along. Nice work. Bob
- 745 replies
-
- francis pritt
- mission ship
-
(and 1 more)
Tagged with:
-
The name Barkentine caught my eye. Many years ago I worked at the Barkentine Book Store in California. They only carried books about boats and I spent most of my pay on books from there. It would be nice if there were full plans for all boats ever built but sometimes all you can do is find as much as you can and then draw the plans yourself. That’s what I had to do with the HOGA tug. I’m sure you’ll come closer to the true lines then you feel you can. Bob
- 20 replies
-
- radio
- barkentine
-
(and 1 more)
Tagged with:
-
Beautiful build with such detail. You challenge others ( me) to try and do as well just by showing it can be done. Bob
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.