Jump to content
MSW Spring Donation Drive

Stuntflyer

NRG Member
 View Profile  See their activity

  • Posts

    1,136

  • Joined

  • Last visited

 Content Type 

Everything posted by Stuntflyer

  1. Stuntflyer
    Regarding the two stern filler pieces, here are mine installed. Hope this helps. Mike
  2. Stuntflyer
    Nice work, Chuck! I know you're still undecided, but I'm leaning now towards the blue-gray slate roof rather than natural. Mike
  3. Stuntflyer
    Natural, Mike
  4. Stuntflyer
    Chuck, you're doing a great job on the QGalleries. Very methodical and neatly done. Did you manage to straighten out the frieze with the name? How is the tissue paper working out? Mike
  5. Stuntflyer
    Love it, Chuck! Could the moldings be added after the frieze is in place in order to hide frieze edge? Mike
  6. Stuntflyer
    Yes, the molding sits on top of the planking. Mike
  7. Stuntflyer
    Rusty, Check the vertical timbers as well. Not sure how much it matters, but 2 of them are parallel to each other. Mike
  8. Stuntflyer
    The second planking belt, now completed, has proven to be the most difficult one to do so far. I'm told that the last two belts will be much easier to complete which is good news. After seeing Chuck's taped off molding bands that run both through and above the gun ports, I was very curious as to how this would look on my ship. I wanted to know if the gun ports, fixed blocks and sheer were correct. Using measurements taken off the plan drawing I transferred the lower molding position onto the hull (turns out that the lower molding runs parallel to the wales). 1/8" tape was placed onto the hull to simulate the lower molding that runs through the gun ports. After eyeing the run from several positions I could see that some very slight tweaking was needed in order to establish a smooth run. Once satisfied, I added the simulated 3/32" upper molding which runs parallel to the lower molding. I was happy to see that both sides of the hull are almost identical with regard to gun port placement as well as sheer height and shape. Mike
  9. Stuntflyer
    Nicely done, Chuck! Thanks for the heads up on the molding strip widths and using tape to establish a proper run for each. You've peaked my interest in knowing how accurately I have planked that upper section. Mike
  10. Stuntflyer
    I saw Chuck's Winni last week at the house and it looks even better than the photos. . . Mike
  11. Stuntflyer
    Joe, here are my findings regarding the planks going into the stem. . 1. Bevel the outside edge that goes into the stem as well as the inside edge. I find that it's the best way to hide the inside edge of the stem, leaving a nice transition between the plank and stem. 2. I have not found it necessary to bend the plank along its length around a "canister cap" or other round shape. I Just edge bend the plank enough so that its edge conforms nicely to the plank below while at the same time hugging the bulkheads that it crosses. Mike
  12. Stuntflyer
    Chuck, beautiful work as always. I'm a bit behind you on my planking and that's a good thing. Your photos are very helpful, but as always make things seem easier than they really are. Now would be a great time for all those building the Winni to chime in on some of Chuck's expertise in planking techniques. Mike
  13. Stuntflyer
    Looking very nice, Bob. Something that I almost forgot to do was to check the stern framing angle off the plan. Initially I was relying on how the frames sat in the bulkheads. Mike
  14. Stuntflyer
    Yes, Joe, I use a 1 3/8" dowel or hard plastic container to curve the plank along its length. Just dampen, clamp and heat with a hair dryer. The curve can be finessed by hand afterwards. Mike
  15. Stuntflyer
    Thank you all for the kind words and "Likes". Very much appreciated as always. Mike
  16. Stuntflyer
    Work is now completed on the second belt. Not much to say other than more of the same. Just some cleanup sanding and as always I try to avoid sanding too much of the last few installed strakes. The knee is getting a bit grungy due to excessive handling, though not a problem to clean up later. Mike
  17. Stuntflyer
    Dave, You're off to a great start. I suggest that you can cut the inside bulkhead extensions, extension tops and the area of the false deck to the line, being careful that the line shows afterwards. You will take off more material on the inside extensions when you fair the hull inside. The false deck area will be much easier to sand or file now rather than after the bulkheads are glued to the bulkhead former. Mike
  18. Stuntflyer
    Looks very familiar, Bob. Glad to see that your up and running. I think you will really enjoy building the Winni. Mike
  19. Stuntflyer
    This is how I hold the hull steady while planking below the wales. I can slide the Kleenex boxes left or right depending on what section of the hull I'm working on. The painters tape can be released and reapplied several times before losing adhesion. I've been using this edge bending jig since my 18th Century Longboat build. Recently I adapted this variation on Chuck's center hold down. Mike
  20. Stuntflyer
    I glue each plank to the bulkheads and as well as the adjacent planks. Mike
  21. Stuntflyer
    Thanks, Rusty! I'm looking forward to seeing your progress on your "new" Winchelsea build. Mike
  22. Stuntflyer
    Planking below the wales is one of my favorite parts of the build. I have now completed the first belt on the starboard side. Working with boxwood is great though I have to work slowly if I want to get a nice result. On a good day I can complete one strake. I'm Just taking my time and treating each plank as a project in itself. Edge bending is my new friend and I'm finding, for the most part, it's all that is needed. The exception being where the plank sweeps upwards into the counter. There I use a dowel to form the shape. In all cases I use the hair dryer after wetting the wood for 10-15 seconds. Some preliminary cleanup sanding was done while leaving the last installed strake mostly untouched until more planks are added below it. Mike
  23. Stuntflyer
    I don't know about that, Boyd. .5mm seems like a lot to be off by, but perhaps you will be okay. Good luck! Mike
  24. Stuntflyer
    Nice fix, Matthias! Mike
  25. Stuntflyer
    I find that a dull blade tends to wander. Is the blade worn? Mike

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...