Dr PS - Paul Schulze Posted October 14, 2019 Author #61 Posted October 14, 2019 Completed the Compass and Compass Box. The Box was made from 1/32” basswood sheet according to plans. Compass Rose reduced in Photoshop. Lens effect was made using a drop of CA glue. In the first photo below, the box slides were glued to a scrap of wood as shown, then glued to bottom of Cuddy. When the glue was dry, the scrap was cut away leaving the slides attached. G.L., J11 and GrandpaPhil 3 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted October 17, 2019 Author #62 Posted October 17, 2019 (edited) Tiller and Rudder completed. The Gudgeons and Pintles were made from the supplied thin 3/8” wide brass strip. The Pintles were formed and fitted to the rudder and small brass nails were soldered to them to serve as the hinge pins. The Gudgeons and Pintles were attached using small copper nails. The Tiller was “riveted” with copper nails The Steering Oar Brace is also shown in the last photo. The support brace was made from 1/32” brass wire. Edited October 17, 2019 by Dr PS - Paul Schulze J11, G.L. and GrandpaPhil 3 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted October 18, 2019 Author #63 Posted October 18, 2019 The Whaling Gun Box was constructed from 1/16” sheet boxwood. The ends fit the curve of the ceiling. The front side joins the two shaped ends while the backside is formed by the ceiling itself. The top was split as shown and the front piece was hinged to the back piece by leather strips. The box was stained to match the Bow Sheet. Sea Hoss, Ryland Craze, JpR62 and 1 other 4 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
G.L. Posted October 18, 2019 #64 Posted October 18, 2019 (edited) She is looking just as a real one, Paul. Edited October 18, 2019 by G.L. Quote G.L. Current projects: Oostends schipje (Ostend shrimper) - scale 1:20 Clipper d'Argenteuil - POF - scale 1/15 - SMALL Completed projects: Norwegian Whale Boat - POF - scale 1/10 - SMALL Anatomy of a boat by G.L. - scale 1/10 - POF - SMALL Day gaff sailing boat with center board - FINISHED - SMALL - scale 1/10 Cross section fishing smack - FINISHED -scale 1:20HMS Triton cross section - FINISHED - Scale 1:24
Dr PS - Paul Schulze Posted October 18, 2019 Author #65 Posted October 18, 2019 4 hours ago, G.L. said: She is looking just as a real one, Paul. Thanks G.L. 1 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Sea Hoss Posted October 18, 2019 #66 Posted October 18, 2019 I agree, very sharp and genuine looking! Quote Current: Emma C. Berry Lobster Smack-Model Shipways-1:32-1866 Back on the shelf: USS Essex- MS- "Old Yellow Box" Solid Hull Wall Hanger (Half Hull) Completed: 18th Century Armed Longboat-MS 1/24 USN Picket Boat-MS 1864 1/24 US Brig Syren by Sea Hoss- Model Shipways-1803 18th Century Carronade/Ship Section Mayflower-Pilgrims Pride by Sea Hoss-Model Shipways-1620 18th Century Long Boat by Sea Hoss-Model Shipways USS Constitution by Sea Hoss-Revel-Plastic
Dr PS - Paul Schulze Posted October 19, 2019 Author #67 Posted October 19, 2019 7 hours ago, Sea Hoss said: I agree, very sharp and genuine looking! Thanks The Lazy Saint 1 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Scoot Posted October 22, 2019 #68 Posted October 22, 2019 Had the paint decision on my Whaleboat also. Decided to leave one side natural and paint the other. that way it could be displayed two ways. Fun model to build. Yours is coming along nicely. Enjoy. Scoot J11, GrandpaPhil, JpR62 and 1 other 4 Quote Charles W. Morgan
Dr PS - Paul Schulze Posted October 22, 2019 Author #69 Posted October 22, 2019 Scoot, your boat looks great. I have already started painting and my hull scheme is the same as yours - green with the second strake white. Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
GrandpaPhil Posted October 24, 2019 #70 Posted October 24, 2019 Excellent! J11 1 Quote Building: 1:200 Russian Battleship Oryol (Orel card kit) 1:64 HMS Revenge (Victory Models plans) 1:64 Cat Esther (17th Century Dutch Merchant Ships)
Dr PS - Paul Schulze Posted October 26, 2019 Author #71 Posted October 26, 2019 (edited) Been doing a lot of work around the house getting ready for winter so the NBW has been on the back burner for a while. With the holidays coming up posts will be few for a while but I will work on the boat as I get a chance. I did get the hull painted though. Next I will be trying to do various detailing of the inboard side. Edited October 26, 2019 by Dr PS - Paul Schulze J11, GrandpaPhil, Scoot and 2 others 5 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted November 11, 2019 Author #72 Posted November 11, 2019 Only worked on the NBW for a few hours and have partially finished the oars and paddles. I decided to carve the complete pieces from 1/8” basswood sheet instead of using the provided precut parts. This should make for a better look after staining. In the photo, the oars are pretty much done. Four more paddles need to be cut out before the final shaping of all six. G.L., GrandpaPhil, JpR62 and 2 others 5 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Arthur Wayne Posted November 12, 2019 #73 Posted November 12, 2019 I wondered where you ran off to! I like your color scheme. I can't say I envy you for having to make all of those oars! You must be in the home stretch now, if you get it done soon enough maybe Santa will drop off another cool model. Quote Current Build: Gunboat Philadelphia Completed Build: MS 18th Century Armed Longboat
Dr PS - Paul Schulze Posted November 12, 2019 Author #74 Posted November 12, 2019 Arthur, thanks. There are lots of details to work out before I put this one to rest. One could skip a lot of the details like a raised stitched sail and loads of Whaleboat craft but I plan to push through. However, I am going to take time off to build the MS Civil War Coffee Wagon as a Christmas present for someone. Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
hmshipyards Posted November 12, 2019 #75 Posted November 12, 2019 Late to the party, but pulling up a chair to watch. Quote
Dr PS - Paul Schulze Posted November 16, 2019 Author #76 Posted November 16, 2019 On 11/12/2019 at 12:53 PM, hmshipyards said: Late to the party, but pulling up a chair to watch. Welcome, moving slow but doing a little bit at a time. Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Jack12477 Posted November 16, 2019 #77 Posted November 16, 2019 On 11/11/2019 at 11:24 PM, Dr PS - Paul Schulze said: However, I am going to take time off to build the MS Civil War Coffee Wagon as a Christmas present for someone. That is a very nice kit. I built in several years ago. Quote Jack "No one is as smart as all of us" - Is ón cheann a thagann an cheird The craft comes from the head --------------------------------------------- Current build: US Constellation Non-ship builds: USCG UH-65A Dolphin M16 Multi-gun motor carriage diorama M4A3 Sherman Tanks dioramas 1936-1939 Mercedes Benz 540K 1934 Rolls-Royce Phantom II JSDF Light Armor Vehicle Figures: The Last Bridge: Raider Reaper Edge of Universe: Ianis The Last Bridge: Vadim with cart Completed build log(s): 18th Century Longboat , Marie Jeanne, Willie L Bennett 1888 50 ft Gaff-rigged Ice Yacht Scratch Build The Sullivans (DD 537) Liberty Ship SS John W Brown USS England (DE 635), Artesania Latina Titanic Lifeboat Gallery: Swift , Armed Virginia Sloop, Santisima Trinidad Captain's Launch , 18th Century Longboat , Marie Jeanne Other: Rhinebeck Aerodrome Tour
Dr PS - Paul Schulze Posted November 19, 2019 Author #78 Posted November 19, 2019 (edited) I have the stern fairly well in hand now except the knife. The rudder is painted and the Tiller is fastened. The Tricing line (lower stopper knot on rudder) runs up port side through a Fairlead in Cuddy to port cleat. The Trip line (upper stopper knot on rudder) runs up starboard side through a Fairlead in Cuddy to starboard cleat. The Tricing line hoists and holds the rudder when the Whaleboat is hoisted on the mothership. The Trip line is used to light the rudder off the Gudgeons. The final line completed was the Steering Oar Strop. It has a stopping knot in the stern post, then runs to the Steering Oar Brace on the port side, back through the stern post and attaches to the cleat on the Lions Tongue with a Lanyard. Edited November 19, 2019 by Dr PS - Paul Schulze Scoot, GrandpaPhil, G.L. and 4 others 7 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Sea Hoss Posted November 19, 2019 #79 Posted November 19, 2019 Just caught up on your W.B., looks fantastic and makes me so want to do one too! J11 1 Quote Current: Emma C. Berry Lobster Smack-Model Shipways-1:32-1866 Back on the shelf: USS Essex- MS- "Old Yellow Box" Solid Hull Wall Hanger (Half Hull) Completed: 18th Century Armed Longboat-MS 1/24 USN Picket Boat-MS 1864 1/24 US Brig Syren by Sea Hoss- Model Shipways-1803 18th Century Carronade/Ship Section Mayflower-Pilgrims Pride by Sea Hoss-Model Shipways-1620 18th Century Long Boat by Sea Hoss-Model Shipways USS Constitution by Sea Hoss-Revel-Plastic
Dr PS - Paul Schulze Posted November 26, 2019 Author #80 Posted November 26, 2019 Been away from this build for awhile but I finally finished the Civil War Coffee Wagon and now plan to work on the NBW again. Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted December 1, 2019 Author #81 Posted December 1, 2019 Not a whole lot to report, but I did get the oars and paddles finished. jgodsey, G.L., Tigersteve and 1 other 4 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted December 6, 2019 Author #82 Posted December 6, 2019 I am now working on a Civil war Limber to go with my finished Coffee Wagon. However, I did get the mast and sprit pole finished and ready for the sail. I have not decided how I want to do the sail. This will be a challenge no matter what I do. Rings for attaching the sail to the mast were made by drilling a hole in a dowel larger than the mast and then sectioning it. Mast and Sprit pole. GrandpaPhil, G.L. and Tom E 3 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted December 17, 2019 Author #83 Posted December 17, 2019 I finished the Civil War Coffee Wagon and Limber. I am working very slowly on the New Bedford Whaleboat but realize that making the sail is going to take me to another whole skill level. I need to learn how to sew. I will be doing some practicing with the help of my wife and her Bernina sewing machine. After the first of the year, I hope to start up again. In the meanwhile, Merry Christmas and Happy New Year. Sea Hoss and tmj 2 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
the learner Posted January 4, 2020 #84 Posted January 4, 2020 Try using paper Quote Cheers, GuyThe LearnerCurrent Member NRG,SMA Current Build: HMS Triton 1:48 on line
Dr PS - Paul Schulze Posted January 4, 2020 Author #85 Posted January 4, 2020 4 hours ago, the learner said: Try using paper How does paper work out? Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted January 6, 2020 Author #86 Posted January 6, 2020 Finished the Rowlocks, TubOar Lock and harpoon racks a while back and started on the lantern. I bored a hole in a 1/4” square rod, carved out the “windows,” mounted 28 gauge wire in place for grills and painted it brass color with some black streaks. The grill bars were bent at each end and put into holes drilled into the wood. Next was/is to finish the cooperage which I started before finishing the lantern. G.L. and GrandpaPhil 2 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted January 6, 2020 Author #87 Posted January 6, 2020 (edited) I completed the “bucket “ drogue, bucket, piggin, water and lantern kegs, waist tub and line tub. The stave sheets were scored and bent to fit the plugs. After gluing and drying, all items were stained with a dark oak stain except the water and lantern kegs which were painted the green hull color. The hoops were made from 1/16” slices of Bristol paper darkened with India ink and glued on last. Eye splices on the end of the whale line. Hoop strips Each tub was completed by coiling two flakes or layers on each. Lines connecting the two tubs and drogue are shown. The line goes around Logger Head to the bow. Excess line is coiled in the box at the bow. The Painter or towing line is shown coiled on the port side behind the thigh board. The drogue is attached to the whale line with a Double Becket Hitch. Piggin Cannot get rid of following photos. Deleted them but they keep appearing. 😳 Edited January 6, 2020 by Dr PS - Paul Schulze sferoida, G.L., Tigersteve and 2 others 5 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted January 6, 2020 Author #88 Posted January 6, 2020 (edited) The Grapnel was made from 20 gauge galvanized wire. A length was folded twice yielding four strands. The strands were twisted tightly and soldered to form the shank. The end loops were cut open and the resulting tines were bent into an eye at one end and four prongs at the other. Grapnel painted black with line attached Grapnel stowed under Thigh Board in bow. Edited January 6, 2020 by Dr PS - Paul Schulze GrandpaPhil and G.L. 2 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted January 6, 2020 Author #89 Posted January 6, 2020 I delete photos from text, not download area and some pop up in text. I cannot seem to delete them unless I trash them from download area which I don’t want to do if the.photo is used elsewhere in the text. Any suggestions? Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Dr PS - Paul Schulze Posted January 6, 2020 Author #90 Posted January 6, 2020 Some pics of progress so far. GrandpaPhil, Tigersteve and G.L. 3 Quote Paul Cutty Sark, Scientific Models (no build log) 18th Century Armed Longboat, Model Shipways Civil War Coffee Wagon and Limber, Model Shipways side project New Bedford Whaleboat, Model Shipways Civil War Gatling Gun, Model Shipways side project
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.