-
Posts
3,498 -
Joined
-
Last visited
Everything posted by captainbob
-
20 gauge shackles
captainbob replied to michael mott's topic in Metal Work, Soldering and Metal Fittings
Michael, what a great touch with the torch. Last time I melted the end of a wire, by mistake, it ran half an inch before I could get the torch away. Bob -
Thanks Keith, now I have something else to learn. Bob
- 420 replies
-
Band Saw Question... or two
captainbob replied to mtaylor's topic in Modeling tools and Workshop Equipment
Mark, it is true that a large powerful saw will do everything you ask of it. But I bought a Ryobi 9” band saw from Home Depot for around $100, three or four years ago and have not been disappointed. Earlier someone mentioned the guide blacks and how rollers are better, the Ryobi has six rollers, three above and three below, so there is no wear or heat from blocks. No, I cannot cut anything six inches thick but so far I have not needed to. I have cut 3/4” Rosewood and 1/4” brass and I can’t think of anything harder I would need for a model. Bob -
Harriet McGregor by Boccherini
captainbob replied to Boccherini's topic in - Build logs for subjects built 1851 - 1900
Nice looking metalwork. It's that sort of thing that makes a model really stand out. Bob -
Russ your schooner is coming along nicely. Oh, and thanks for showing that 1920’s picture. The attachment of the deadeyes to the chain plates is interesting, but what I notice is that the excess lanyard is not tied and bound up against the shroud but after a hitch around the shroud is allowed to hang down. Interesting. Maybe for easy readjusting later? Bob
-
Russ, Keith, Thanks for looking in and for the help. If I used harder wood scraping alone would probably work, but the deck is bass wood and the scraper occasionally grabs the grain and tears out chunks. Or maybe it is just that the scraper is not sharp enough. Bob
- 420 replies
-
Pete, I think you're doing fine. The last time I moved it took me six months to get set up so I couold get back to modeling. Bob
- 153 replies
-
- musongus bay
- sloop
-
(and 1 more)
Tagged with:
-
Russ, John, Elia, Michael, Pete, Popeye, Thanks to all of you and to the likes. In my attempt to get the deck as smooth I planed, scraped, and sanded, probably no special order, I did them all several times. I think sanding was the last. Bob
- 420 replies
-
Painting Brass
captainbob replied to captainbob's topic in Painting, finishing and weathering products and techniques
The mfg. says: CLR is a powerful formula available for dissolving tough calcium and lime deposits and surface rust stains from: • Tubs • Toilet bowls • Sinks • Glass • Chrome. Bob -
Michael you asked, way back in #170 <, if I was going to be adding any support at the edges where the planks but up to the cover board. The answer turned out to be yes and no. In most cases the deck beams were sufficient support but at the master beam the planks were so short I had to put in little pieces for support. Anyway now the deck is finished and I can move on to deck furniture, masting and rigging. Bob
- 420 replies
-
Several years ago, I thought of building a brass locomotive. So I joined the brasslocobuilders forum. I never built the locomotive but I still get email from them. This was posted today and I thought I might be interesting to some here. I have not tried it but it sounds good. Heading: “Painting Brass” Q. What recommendations do people have as to prepare a brass loco for its undercoat? The model is old, dirty & tarnished a bit. A. Soak it in CLR for about 15 minutes use disposable rubber gloves so you are not handling the brass with bare hands, after you take it out of the CLR, rinse it in clean tap water and place it into a drying oven, [old oven with a 60W bulb] when it is dry I then wash it in clean thinners and again let it dry, and then give it its first coat of etch primer [auto etch primer]. You can make a drying oven by using an old metal mail box with a 60W bulb inside. Slide the model in and turn on the light, close the door and leave it for 30 minutes to an hour. Keep in mind the CLR leaves a slippery coating on the brass; make sure you rinse it properly especially in nooks and crannies, or you may have problems with the paint not bonding. I generally use an old tooth brush or an artist brush about 1/2” wide. Bob
-
I've done that too many times. "I better put that somewhere for safe keeping." That is often the last I see of it. Good luck in finding the Herreshoff. That should be a fun build. Bob
- 153 replies
-
- musongus bay
- sloop
-
(and 1 more)
Tagged with:
-
What a joy it was seeing this lovely cross-section come together. Thanks for letting us watch. Bob
- 421 replies
-
- granado
- bomb ketch
-
(and 2 more)
Tagged with:
-
They are all lovely. How many do you plan on making? Bob
- 153 replies
-
- musongus bay
- sloop
-
(and 1 more)
Tagged with:
-
Elia, Thanks for showing how you assembled the chainplates and deadeyes. It helped me with mine. Bob
-
Thanks for the extra pictures. She's a fine looking boat. Bob
- 86 replies
-
- muscongus bay lobster smack
- Midwest Products
-
(and 1 more)
Tagged with:
-
Comming right along and looking good. Bob
- 144 replies
-
- corsair
- bermuda boat
-
(and 1 more)
Tagged with:
-
You're weaving them yourself ? I think that would be a first for MSW. Bob
- 2,207 replies
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.