Beef Wellington

I have recently purchased the HMS Wolf, a Shipyard paper model, from Cornwall Model Boats in the UK, I also purchased the extra sails and masts sets but was reticent to splash out on the laser cut blocks, however after receiving the model and seeing the size of the parts, each just a few mm and all containing multiple parts I have decided to save my eyes and will place an order for these as well. I was considering purchasing laser cut timber blocks however it seems an extravagance for a simple card model. However I may purchase wooden gun carriages and associated brass guns depending on how I go with cutting and assembling the card parts and the model generally. 
 
I have only one complaint in that there was a couple of pages of assembly instructions missing from the kit. I am really hoping that Cornwall are able to convince Shipyard to email me a pdf of the missing pages. Hopefully, as its assembly details and not parts details that are missing there will not be any issues. I will email Cornwall tomorrow.
 
The beauty of this card model is the skeleton is laser cut.  I have recently been struggling with cutting and assembling the skeleton for the RMS Mauretania and I find it very time consuming. I have been on that build for several months and have still not progressed beyond the skeleton!
 
Following Dan's lead I have been busy cataloguing all the parts into a spreadsheet with part numbers, page numbers, thickness of any laminations, names of the parts/ assemblies and any relevant comments and then cross references to assembly pages.
 
Anyway here are few some photographs of the kit -
The cover, and example assembly and parts pages. Note there is only one colour page of assembly details the rest are black and white. Other than  the rigging details all assembly detail is by photograph (no words).
A close up of some of double blocks parts as you may be able to discern in this example each block contains 7 parts all of which need to be laminated to either  0.25mm or 0.50mm card. The length of the block in this example is just a few mm.
An extract of the assembly instructions for the blocks in question.
The assembled skeleton - the majority of the skeleton has been assembled - I think it took less than 15 minutes to dry fit it.
 
I really must say the quality of the laser cut card is absolutely top drawer.
 
 
 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Chuck - where do you get your brass strip from, or do you cut it yourself from sheets? If so, how do you do that?  Many thanks.

Maybe, probably.....  But that would be a bit "kitchen sink" for my tastes any way.  No need to add every little doo-dad just because it would have been there.  I think it would be very distracting and isnt warranted.  But you guys can always add it in.    I dont think its worth the risk of splitting that thin cap rail.  It would be pretty tough to fix at this point.
 
 
 
Chuck

I do sometimes cut my own brass strip but the stuff I used this time is a common size.  Its available commercially.  Its from K&S.  1/32 x .025 or 1/64.
 
http://www.ksmetals.com/29.html
 
Chuck

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Chuck - where do you get your brass strip from, or do you cut it yourself from sheets? If so, how do you do that?  Many thanks.

Thanks....yes I am not a big fan of those brass and/or bulbous wooden belaying pins.  Easy enough to make them myself and you only need four for the longboat.   The knees are all finished now.   I will add the roller and fixed block sheave on the stem next.
 




 
 
 
 

Greeting Stergios, not sure if this helps.   I remember being very confused by this myself.  Here is what I did to solve the problem, I can't guarantee it is the correct solution, but sharing in case it gives you a better idea.  You can see its still work in progress!
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Will definitely be following along on this, love the pre-Dreadnaughts.  Looking at her beside the Yamato without all the extraneous deck fittings and armament in picture above shows a lot of resemblance to form U-boats and later submarines.

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Having looked at Joe V's excellent Granado I tried to duplicate the trim on his forecastle capping.  His method entailed scribing a channel down the centre of a piece of a (roughly) 2.5x1mm timber strip.  My channel looked like a dog's breakfast and so I looked for an alternative.  I then took a piece of 2x0.5mm strip, painted down its centre, then glued pieces of 1x1mm strip on each side.
 
Here are the results.  As you will see, the gaps are slightly different, but at 'lifesize' the difference is scarcely noticeable.  Nevertheless I will make up another one, then choose the best two of the three.
 

I thought bending may be a problem, but it turned out quite well.

 

Will definitely be following along on this, love the pre-Dreadnaughts.  Looking at her beside the Yamato without all the extraneous deck fittings and armament in picture above shows a lot of resemblance to form U-boats and later submarines.

Thanks for the encouragement gents, certainly helps one stay motivated.
 
Channels:
 
I realize I'm continuing to bounce around, so apologies if this is not the most sequential log.  Have been continuing to work on the deck fittings, none of which are glued in place yet (posts to come), but diverted to the channels.  I think it will makes sense to have the channels and chains in place before any of the cannons are finally fitted - they just seem to be  too exposed to not court disaster.  This seems a "damned if you do, damned if you don't" situation so any advise here would be gratefully received.
 
I'd share the approach to the channels in an earlier post, so luckily work was more just final finishing.  I wanted to introduce the rather pleasing profile on the edge as it seems to reduce the perceived bulk of the channel noticeably to my eye.   I have to say, this has been some of the most challenging 'scraper work' I've yet done.  Getting clean (or as clean as I can!) edges on all of the compound curvatures, as well as dealing with scraping across end grains at the fore and aftmost faces proved a real challenge.  To add to this, I realized that the batten that keeps the chains in place also needs to be profiled.  I'm taking the approach of temporarily gluing the batten in place, profiling, and then will de-bond using rubbing alcohol.  The thinking being that once these are shaped, it should be relatively straightforward to glue permanently once the deadeyes and chains are in position.  Each one will be carefully notated so I can match them up again.  I've put on a very thin coat of wipe on poly to enhance the visibility of the profiles surface and see where I am...there will definitely need to be a little fine tuning once all are done, bit hopefully this illustrates.
 

 
I'm following the NMM plans as closely as I can, which show both the initial draft with open quarterdeck, as well as the changes when the quarterdeck bulwark was built up.  Not only does the position of the channels change, but the alignment of the chains.  Not having had the plans earlier, I had used the kit supplied template as a foundation.....  I have now reached the point in the build that every Artois class builder doing an open bulwark version seams to reach, which is the realization that the position of the quarterdeck ports  need to be modified - wish I'd ordered the NMM plans sooner.  The gunport openings changed when the position of the channels was changed with the addition of the built up bulwark.  This will require the position of the gun ports to be corrected.  How I wish that I had simply planked over the kit template rather than planking around the ports, it would have made a fix unnecessary.  I'm moving on while I consider how best to do this.
 

 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these. 
 

Well I'm back on track at least after the destruction, painful, but glad its behind me....
 
The bigger channels are completed now and ready to be glued into position, I'll be leaving the attachment of the smaller channels for the topmast backstays until after the quarterdeck is glued into position.  A final finish has been put on the hull, which means that I can now start to put some of the detailing in place in conjunction with fitting the chains.  There seem to be a number of position where space will be tight, so fingers crossed previous planning works out.
 
For reference, I've marked out the expected position of the quarterdeck ports (and the previous template position with a dotted line) but will not be cutting these out until the quarterdeck is in place.  This shows them in relation to the actual position of the deadeyes, with a bit of imagination (I used string and a mock up of the masts) its clear that the previous port locations would be obscured (the second and third from the stern are the tricky ones).  Even though not obscured, the 4th port from the rear was moved so the port separation is equalized as much as possible.  My advice to anyone modifying the kit (or even building from the box) is to leave the positioning and cutting out of any these quarterdeck ports until after the final position of the deadeyes is known.
 
Unfortunately, the PE hinges supplied in the kit are too small and dimension, and too bulky, for the sizes of the sweep/airing ports estimated from the AOTS plans.  Luckily I had purchased a PE set for (I think!) the HMS Grenado way back and it contains some useable hinges.  These smaller PE sets are pretty reasonably priced, and I've found can be handy to have as they contain a multitude of potentially useful fittings (hooks etc.) which can be used to supplement the older 'bare bones' CC kit PE sets.
 
These were given a few coats of paint to bulk them up a bit as although they are theoretically the same scale, the ports on Grenado are of smaller dimension.  Placement on the airing ports proved a little challenging due to the elevated profile of the black-strake that runs through these.