Flying Dutchman/Black Pearl by Glen McGuire - 1/700 - BOTTLE

[Keith Black]

7 hours ago, JacquesCousteau said:

Looking forward to seeing how you get this one in the bottle.

 He'll get it in there, he always does. 

 

 

Edited October 22 by Keith Black

[BANYAN]

6 hours ago, Glen McGuire said:

  I think I can...I think I can...I think I can...

I know you can, I know you can, I know ...   Looking good Glen.  That's a mean lookin' little ship.

 

cheers

 

Pat

[Javelin]

Great looking Dutchman (At least one on this planet then 🤣)! 

 

So I was recently thinking about your project and I was thinking about the little parasols you get in some drinks. Perhaps that concept could be an idea for the whirlpool. Insert with head first, tilt it with the head down and open it by sliding the mechanism down. 

You'd have to design your own parasol for proper size, shape and material though. 

On the upside, you could make the stick long enough to touch the top of the bottle, so it doesn't float. 

Just another brain fart. 

A solid cone is still preferable, but I just don't see a good solution for the moment. 

I guess this project would be easier with a bottle in upright position (neck on top), but you'd need a low, wide bodied bottle for that (I have one like that, but with an extremely long neck).

 

[Glen McGuire]

2 hours ago, Javelin said:

Great looking Dutchman (At least one on this planet then 🤣)! 

 

So I was recently thinking about your project and I was thinking about the little parasols you get in some drinks.

 

Thanks, Roel.  I hope that dang whirlpool is not keeping you up at nights like it is me!  I agree that it would be much easier with the bottle upright.  But I'm determined to figure out a way to pull this off with the bottle lying sideways.

 

I had a friend over yesterday who is very artistic and we were playing around with some ideas.  DAP makes some UltraClear caulk that I used on the waterfall of my Wa'a Kualua project.  It's workable but holds its shape very well.  We tried coloring it with acrylic paint and it mixed nicely.  My friend's idea was to build the whirlpool in layers outside the bottle - each layer being thin enough (after drying) to roll up, insert into the bottle and place on top of the previous layer.  For a test run, we spread some of the caulk on wax paper, made a few layers, and set aside to dry overnight.  Unfortunately, when I got up this morning and tried to peel the layers off the wax paper, they were completely stuck.  So I will try again using a pane of glass as a working surface. 

 

If it the layering process actually works, I could stack up the whirlpool layers inside the bottle and pour epoxy resin around it.  If I make the epoxy resin with the right amount of translucence, you might actually see the vortex when looking through the side of the bottle.  I think that would be pretty cool.  If IFs and BUTS were candy and nuts...🎄 

Edited October 24 by Glen McGuire

[Keith Black]

 How about using a ballon? Place a ballon in the bottle, blow it up to desired size, pour catalyst around the ballon and once set deflate the ballon. You could put lead weights inside the ballon before blowing it up to keep it from lifting. 

Edited October 25 by Keith Black

[Glen McGuire]

14 hours ago, Keith Black said:

How about using a ballon? Place a ballon in the bottle, blow it up to desired size, pour catalyst around the ballon and once set deflate the ballon. You could but lead weights inside the ballon before blowing it up to keep it from lifting. 

That has to be the most creative idea yet, Keith!  I hope you are not losing sleep over this problem either!  😃

 

Back to the Flying Dutchman though, and the sails in particular.  While watching the movie, I loved the eerie look of the Dutchman's sails - kind of a cross between thick cobwebs and varicose veins. 

      

 

 

A couple of days ago while I was throwing a load of clothes in the dryer, I looked down at my hand and realized I was holding something that just might work for the Dutchman's sails - one of those Bounce anti-cling sheets.  I took one and brushed it with a grayish-black wash.  It looked promising at first glance so I cut out all the necessary sails and gave it a go.

 

 

 

 

I attached the sails to the yards.  I liked the coloring and the veiny effect, but the bottom edge was too clean.  So I shredded it a bit and then was satisfied with the look.  I also started adding the lower shrouds and ratlines.

 

 

Here's where she sits now with all sails in place except for the fore stay sails.  The main and mizzen masts are glued into the deck.  The fore mast is dry fit.

 

 

 

Now it's time to do the special rigging on the fore mast that will allow it to lie down over the bow instead of sternward like the other masts.  

 

[JacquesCousteau]

Very inventive use of the dryer sheet, it looks great!

[Keith Black]

 Fantastic sails, Glen! 

 

[BANYAN]

Now there a lightbulb moment for you.  Great idea and well put into practice - looks great Glen.

 

Keith, where do you get these pics - have you got a a private penguin breeding colony?

 

cheers

 

Pat

[Glen McGuire]

On 10/25/2024 at 5:34 PM, BANYAN said:

Keith, where do you get these pics - have you got a a private penguin breeding colony?

I think Keith's unique mind is its own private penguin breeding colony!!

 

The final challenge for my Dutchman is the fore mast shrouds and back stays.  Normally, I will tie off a shroud to the starboard channel, run it through a tiny hole in the mast (just below the mast top), and tie it off on the port channel.  That works great when the masts hinge sternward.  However, as mentioned earlier due to my poor ship design, I am forced to hinge the fore mast forward to get it to fit in the bottle. 

 

So here's the idea I came up with for the fore mast shrouds and backstays that would allow the mast to hinge forward.  I cut a single 18" long thread and tied 3 other (shorter) threads to it. 

  

 

 

 

Then I installed a small eye pin (1.4mm outside diameter) on each side of the mast just below the crow's nest where I normally would have run the shrouds through the mast to the other side.  I tied off each of the shrouds to the channels then ran the single long thread through the eye pin.  The long thread will run out of the bottle and allow the mast to hinge forward.  Once the ship is in the bottle, I'll raise the mast and the eye pin will meet the knot where the top of the shrouds are all tied together.  

 

 

For the back stays, I did basically the same thing except I did not have to tie any together.  The forward back stays run through a small hole I drilled in the mast just above the crow's nest.  The rear back stays run through an eye pin installed near the top of the fore mast.  The last thing I did was install 2 stay sails above the bowsprit.  The lines are a bit loose because nothing is under any tension until it gets inside the bottle.

 

 

 

And here's how she looks folded up, impatiently waiting for me to make a whirlpool in the bottle.

 

 

With the Dutchman complete, it's time to put the bottle down and get some more work done on the Constitution.

 

Edited October 27 by Glen McGuire

[BANYAN]

Tight squeeze Glen - a mm more here and there and you may have been in trouble - great planning and execution.

 

cheers

 

Pat

[Ian_Grant]

Looks great Glen!

 

Awaiting with bated breath the insertion video!!

 

 

[Glen McGuire]

2 hours ago, BANYAN said:

a mm more here and there and you may have been in trouble

You got that right, Pat.  Had the bottle opening been 1mm wider, the ship would have slipped in the normal way with all masts folding to stern.  1mm narrower and I'd be starting the whole thing over!  All of that speaks to my poor planning up front.  From now on, I just need to make my ships 10% smaller than my original design.

 

26 minutes ago, Ian_Grant said:

Awaiting with bated breath the insertion video!!

Thanks, Ian!  It will be a while though.  I've still got a whole nuther ship to build, not to mention the whirlpool!

[Javelin]

On 10/28/2024 at 3:10 AM, Glen McGuire said:

You got that right, Pat.  Had the bottle opening been 1mm wider, the ship would have slipped in the normal way with all masts folding to stern.  1mm narrower and I'd be starting the whole thing over!  All of that speaks to my poor planning up front.  From now on, I just need to make my ships 10% smaller than my original design.

I don't think that's poor planning at all. It's basically the point of SIB's. If it's not hard or just straightforward, then what's the point?

Adjusting the bottle or the scale just makes it easier and that gives a less brilliant effect. 

Having all those pieces fit nicely would also require so much planning and even construction that you'd already be halfway in the build before you discover all possible issues... That way you'd never really start a build! ( and that's not your style is it? 😋) 

Edited Wednesday at 02:52 PM by Javelin

[Glen McGuire]

1 hour ago, Javelin said:

It's basically the point of SIB's. If it's not hard or just straightforward, then what's the point?

Adjusting the bottle or the scale just makes it easier and that gives a less brilliant effect. 

Words of wisdom.  Come to think of it, they do call the SIB genre "Impossible Bottles", don't they?  Thank you for your perspective, Roel!

[FriedClams]

Nice progress!  Tricky figuring for unfolding the Dutchman.  Sails look appropriately tattered - nice.  Only a modeler would look at a dryer sheet and say to himself - "hey now, look at this material".  You got the disease bad, Glen.

 

Gary

[Glen McGuire]

On 11/2/2024 at 1:53 PM, FriedClams said:

Only a modeler would look at a dryer sheet and say to himself - "hey now, look at this material".  You got the disease bad, Glen.

Takes one to know one, Gary!!  

[FriedClams]

22 hours ago, Glen McGuire said:

Takes one to know one, Gary!!  

 

Very true, Glen.  And as a sufferer myself, I was only offering some friendly intervention before it gets out of hand.

 

Gary

[ccoyle]

1 hour ago, FriedClams said:

 

Very true, Glen.  And as a sufferer myself, I was only offering some friendly intervention before it gets out of hand.

 

Gary

 

Model builder's wife, upon viewing [insert name of junk item here]: "I think this needs to go (in the trash / to Goodwill)."

Model builder: "But that could come in handy for a model some day!"

[Ian_Grant]

28 minutes ago, ccoyle said:

 

Model builder's wife, upon viewing [insert name of junk item here]: "I think this needs to go (in the trash / to Goodwill)."

Model builder: "But that could come in handy for a model some day!"

In the case of Glen and his wife, "junk item" could be construed as "a short section of railway track".