Jump to content

L’Etoile by glennreader - FINISHED - Billing Boats - Scale 1:50 - Updated to represent her current fitting out


Recommended Posts

At the time I got this kit I had just starting building the Caldercraft Snake. Having not built anything for over10 years I thought it might be a good idea to get some practice building the Etoile, which is not really my type of ship, so if I messed up some bits it would not really matter. Also I would not spend much money replacing what is in the kit and try to use as much of the supplied material as possible, as it turns out, now I have started my attitude has changed somewhat, more on that later.

 

The Kit

 

 

This is an old Billings kit which I do not think is still available. I was offered it by a friend who had bought it as a present for her father, a railway modeller, who hardly touched it. When I got it I did a quick inventory to ascertain if it was all present, it appeared to be. The model was sold in two parts, the basic ship and a fittings kit, both of which were present. It would have looked a bit bare without the fittings kit.

 

 

Examining it the wood seemed to be of poor quality. The edges of most planks were rough and splintering. Also the dimensions were poor. For example, there are strips of some dark wood which are supposed to be 1mm x 0.5mm x 600mm. The width varies from 1.3mm to 0.7mm along the length and this is consistent for all 14 strips.

 

 

There are also a large number of plastic parts, where appropriate I will replace these with wood, if only because there are dimples caused by shrinkage during manufacture. However where these are of suitable quality and used to represent fittings made of metal I may use them. I will certainly discard all the plastic blocks and replace them.

 

 

In general the brass fittings look reasonable or good, though there are some gears supplied for the winches that are a bit bulky and not well made.

 

 

The ship

 

 

Having got the Kit I then started to do a bit of research into it. The first thing I discovered was that it was still in service with the French navy and has a sister ship, La Belle Poule, of which there is a model produced by Dusek.

 

 

They are schooners and were launched at Fecamp in 1932. They are 37.5m long and displace 225 tons. They are built to the design of the Paimpol schooners and were used for cod fishing off the coast of Iceland up until 1938. They were at Dunkirk and can fly the Free French flag. Both of these are now in the French navy and are part of the sea training school.

 

 

Having discovered the ship was still active I got some pictures from the internet (see below).

 

 

Sources of information

 

 

I have also downloaded the instructions for the Dusek model (thank you), which represents the way these ships are currently fitted out. I am using these instructions and photographs from the internet to help me modify the model to look as the ships currently look. In reality there are only minor changes. The most notable are:

 

 

·        The ships wooden boat has been replaced with an inflatable.

 

 

·        Deck furniture – In most cases there are cosmetic differences, but in a few places they are more structural.

 

 

·        The anchor/chain gear has been updated.

 

 

In my next post I will get into the build.

 

 

Glenn

 

post-17393-0-30843700-1486045745_thumb.jpg

post-17393-0-98425300-1486045753_thumb.jpg

post-17393-0-13161300-1486045762_thumb.jpg

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

Hi Glenn,

if you would like to build the ship, I strongly recommend to get the original plans for her from here

http://www.aamm.fr/boutique/index.php?main_page=product_info&cPath=65&products_id=216

 

I have got them and they are well worth help for any serious builder. Both the kits (BB and Dusek) are in 1/50 scale and somehow based on these plans. But only if you first time see the plans you will realize the difference. Of course commercial kits need to be somehow simplified, but with the help of the plans you can really upgrade your buildto other level! Also beware, the ship appearance changed through her carrier and the plans shows her as in service in late 40ies I think....

"A smooth sea never made a skilled sailor."

 

Completed: Smuggler

 

 

 

Link to comment
Share on other sites

Thanks very much for the pointer, I had not found this. I should have realised there would be a French equivalent of the NMM.

 

I know I said originally my intention was not to spend too much money on this, but as I have got into the build I have got more and more involved and interested. The cost of the plans now seems small, I have already spent over £50 on various bits and pieces and am compiling a long list for my next order. Only little things but it soon adds up.

 

I have seen the differences in appearance in some of the online pictures I have found. I have quite a collection now. The addition of navigation aids and radar have changed significantly between refits. I think my biggest problem is trying to work out changes to the rigging from that given in the kit.

 

Thanks again,

Glenn

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

Thanks very much for the pointer, I had not found this. I should have realised there would be a French equivalent of the NMM.

 

I know I said originally my intention was not to spend too much money on this, but as I have got into the build I have got more and more involved and interested. The cost of the plans now seems small, I have already spent over £50 on various bits and pieces and am compiling a long list for my next order. Only little things but it soon adds up.

 

I have seen the differences in appearance in some of the online pictures I have found. I have quite a collection now. The addition of navigation aids and radar have changed significantly between refits. I think my biggest problem is trying to work out changes to the rigging from that given in the kit.

 

Thanks again,

Glenn

You are welcome. As you say, the plan price is not so high. They contain lots of detailed drawing for all those cabins, winches, rigging, ship boats etc etc.... everything you would need to get answers.

Edited by juhu

"A smooth sea never made a skilled sailor."

 

Completed: Smuggler

 

 

 

Link to comment
Share on other sites

Hi Glen, and welcome to MSW. I was excited to see your post because I built this model some time ago and have not seen it since. You are very lucky to have acquired such a unique kit. Mine was built pre-MSW and pre-internet, truth be told, so I built it much as Mr. Billing intended it. It is to this day, my favourite model that I have built. The lines of the hull and sail plan are a thing of beauty. The kit and instructions are pretty straightforward so you shouldn't have any issues. As you mentioned, the original wood may have to be replaced. My kit contained obechi wood and some mahogany strips, so my kit was an '80's version that I built when it was new. I shall follow along on your build log and re-live my time building this kit.

 

I wish you all the best and many hours of enjoyment.

 

Cheers,

 

Peter

 

p.s. Thanks for posting the photos of the actual ship.

Edited by petervisser

Build Log: Billing - Cutty Sark

 

In The Gallery: HMS Unicorn, HMAV Bounty, L'Etoile, Marie Jeanne, Lilla Dan, Zeeschouw "Irene"

 

A Toast: To a wind that blows, A ship that goes, And the lass that loved a sailor!

Link to comment
Share on other sites

Starting the build.

At this point my intention was still just to use this build to get in some practice before going back to the Shark.

 

I started off by cleaning up all pieces required to make the framework. There are 3 pieces that represent the keel the bow and the stern, these are the first glued together on a flat surface. No problems with warping using this method. When this was dry I did a dry run. The frames are added to the keel using spacers to get the correct separation. Then some strips are added through slots on the top of the frames, followed by the false deck to hold everything in place and give it strength and rigidity. This seemed to work very well giving a strong and stable structure.

post-17393-0-73875200-1486133934_thumb.jpg

post-17393-0-02923300-1486133948_thumb.jpg

I then marked out the line where the planking would meet the keel, bow and stern on each side. then took everything apart and chiselled a slot here to take the planking. I then reassembled everything, this time using glue.

post-17393-0-78843700-1486133948_thumb.jpg

The next step was to add some padding provided to give a greater surface area for glue where the planking meets the bow and the stern, a whole extra 2mm. I sanded these to the correct angle as best as possible before fitting.

I then got out the long sanding blocks and did the hull fairing. This really drove home to me the difference in shape between this hull and my previous 3 builds. There were no tight bends, except maybe in some small areas near the stern where some twisting is required. As I checked my progress by laying on planking strips they sat so easily. I think it was at this point that I began to get more interested in the build.

 

I had been worried about the large gaps between the frames especially because there is only 1 layer of planking. However once faired the planks bent neatly over the frames and I concluded that this would not be a problem.

Fairing complete the next step was to add the two pre-cut strips that go above the deck, then one strake below this. I would later come to realise I had just made my first mistake, but at this point I had still not got fully engaged and done enough research. If you look at the pictures of the real ship in my first post, you will see there are slots along the side where the hull meets the deck. These look like channels to let the water flow off the deck. It would have been easy to include them at this stage but by the time I found out it was too late.

 

Mistake number 2. The instructions tell you to add the first strake below the deck without reducing its width. It would have made the next few strakes much easier if I had ignored this.

post-17393-0-75098200-1486133949_thumb.jpgpost-17393-0-82053400-1486133950_thumb.jpg

I worked out how to do the planking before adding any more. At the bow all strips could be bevelled identically then cut to length when fitting. At the stern it was required to reduce the width of some planks, while in other places stealers would be required.

 

I then applied the garboard strake on each side. Then added further strakes in pairs each side, going down from the top and up from the keel.

post-17393-0-78691000-1486133951_thumb.jpgpost-17393-0-83742100-1486133952_thumb.jpg

My method of planking was to first clean up each strip by sanding to try and get a clean edge, then to soak them. I then clamped them in place and let them dry out. On taking them off they spring back a bit, but generally follow the shape required and are easy to glue in place without any worry of them springing out of place, no pins required. When gluing I found it difficult to glue a whole plank at once and did it in sections.

post-17393-0-82824600-1486133953_thumb.jpgpost-17393-0-34747100-1486133954_thumb.jpg

In the end I was fairly pleased with the way things went, though on cleaning it up a number of problems did appear, mainly caused by the poor quality of the wood. For example in the picture of the completed hull you can see that the joint between the 4th and 5th strakes from the keel is not good. However most of this will be covered up by either the coppering of the wale. I was not happy about that bit of plywood sticking out the front and the line where the planks meet it looks a bit ragged. Something needs to be done there, but I will leave that for next time.

post-17393-0-39458600-1486133955_thumb.jpg

At this point I would mention that generally I do not paint my models. There are two reasons for this: I like the bare wood finish and generally when I paint something it looks worse when I have finished than before I started.

 

Also I apologise for the poor quality of the photographs. I never was much of a photographer, but I will try and improve, or at least find somewhere better to take pictures.

 

Glenn

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

The Hull

The following pictures show the hull as it is at present. I have added the stanchions and capping rail. The stanchions were not supplied in the kit and are from 3x3mm lime. The positioning came from the instructions for the Dursk kit. I have also added the wale, again this differs from the instructions in the kit, though it does conform to the supplied drawings.

post-17393-0-85606000-1486226394_thumb.jpg

At the front I have cut off the ply stem and headpiece and replaced them with one from solid wood. Not sure what, it came from the scrap box. I have also replaced all the head timbers, which were supplied as 3mm ply, which fell apart as I tried to cut it to size or reduce it to the required thickness. These are all made with some lime that I had in stock. This also shows the wale a bit better. The pencil line is where the hull coppering extends to. I will neaten up the bottom of the stem before doing the coppering. That bit of lime on the front of the headpiece was my first attempt to carve the decoration there. I took off to much trying to carve the concave profile. I will remove it all and then try again.

post-17393-0-04268400-1486226394_thumb.jpgpost-17393-0-98183200-1486226409.jpg

A view from the rear. I have cut off the bit of wood that would have held the rudder. It was getting in the way when trying to sand the hull. It will be easy to replace and the whole thing will be covered in copperplates.

post-17393-0-32768200-1486226380_thumb.jpg

This shows a close up of the bows. In these last two pictures it is possible to see the deck planking. I am very unhappy with this and not sure whether just to do it again on top. I used the wood supplied in the kit, which was of very poor quality. It was very thin and impossible to get a clean edge. Trying to darken the edges in any way did not work, so I first tried gluing strips of black paper between the planks, which is how the raised stern in planked. But again the thickness/thinness of the wood made this very difficult.

For the rest of the planking I glued black cotton between the planks. This was much easier to do, but the thinness of the planking meant that in places the cotton was so near the top that it was damaged when finishing. Also I had calculated that there was only just enough material supplied to do the planking if I omitted areas that would not be seen.

post-17393-0-75210500-1486226395_thumb.jpg

Recently I had been working on the hull, but have stopped while I wait for the plans I have now ordered. I have gone back to making the various deck houses, winches and companion hoods. I will move onto these in my next instalment.

​Glenn

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

Nice work Glenn, and what a handsome ship. When it comes to the rigging ,you might have to pick what era of her life you want to model and stick with that. Those photos you posted would make a great reference to her rig.

Bill, in Idaho

Completed Mamoli Halifax and Billings Viking ship in 2015

Next  Model Shipways Syren

Link to comment
Share on other sites

reklein,

 

Thank you. I intend to model her as she is now; after her last refit. However the problem with using pictures from the internet is that it can be difficult to date them. for instance, if you examine the second picture in my first post, near the bottom of the main mast, just forward and to the right, you can see a sort of white dish on a pole. That is an early radar system. Then go to the next picture and look at the top of the main mast, there is dish mounted on the front of the crosstrees. This is the radar system currently mounted. so I can date these pictures, but when you get to close ups which show the rigging in greater detail there may not be any similar information in the shot. Still that's part of the fun, at the moment I am doing more research than building. I am currently waiting for the plans to arrive after the tip from juhu.

 

Here is another picture, someday I will have to translate all those sail names.

 

post-17393-0-28531600-1486295188_thumb.png

 

Glenn

 

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

Since my last post I have received the plans I ordered. They are of very high quality and come with an 8 page booklet about the ship and how to build a model. Unfortunately it is in French so very difficult for me to understand.

 

Deck fittings

 

First a few pictures of the aft cabin, which I now know contains the radio room, the wheel house and the ‘Armoire à Pavillons’. Not sure about this last one, possibly the flag locker.

 

post-17393-0-67499900-1486576151_thumb.jpgpost-17393-0-33794400-1486576169_thumb.jpgpost-17393-0-92463900-1486576169.jpg

 

This is not finished and none of this is glued in place, but there is not too much work left. The reason I stopped was that I was not sure about the brass fittings I was making to represent the door finger plate and air vents. Under a x10 eyeglass they do not look very good, but I am happy with how they look in this photograph so I will continue. I believe the Dusek model has photo etched parts (long sigh).

That pedestal in front of the wheel is the compass. The box in front of that is the ‘Panneau de cambuse’. I guess that means it’s a storage box.

Next a review of the deck fittings at the bow. I do not have a single picture that shows the real ship, just a bunch of them that all show parts. So I will just show the following pictures of the model. Again none of this is glued in place yet.

post-17393-0-20721700-1486576171_thumb.jpg

 

First nearest the bow, each side of the bowsprite are the chain stoppers, then comes the electric chain winch. All these were scratch built. I have made some brass plates, one end of which wraps round the brass rod on top of the chain stoppers and the other end has a slot for the chain. When in position these actually work and prevent the chain running out, while still allowing it to be pulled in. However I have taken them off because I keep playing with them and bending them.

post-17393-0-03536100-1486576173_thumb.jpg

 

On the chain winch, I used what was meant to be a dark metal paint to paint the chain wheels (or whatever they should be called) however they came out looking awful. They were turned from dowel using a drill and files. I will repaint these too look better and paint the rest white. Then a power cable is required which runs from the skylight behind to that box on the side of the electric motor.

post-17393-0-40822300-1486576174_thumb.jpg

 

After this is a skylight, the forward companionway hood and another skylight. The two skylights are as per the kit except that the dark plastic covers have been replaced by new ones made from walnut. The companion way hood is again made from scratch in an attempt to make it look like it does in the pictures. This one is a slightly smaller one than the main one as shown in the next picture.

That is about how far I have now got. I am currently making the ‘Grand clare-voie milieu du poste élèves’. I do not know what that translates as but it is a large skylight just aft of the fore cabin. Shown here in this picture of the Belle-Poule.

post-17393-0-19069100-1486576175_thumb.jpg

 

I have made the lower part which is just a box and am now making the ‘windows’, of which there are two each side which can be opened independently. As I cannot make working hinges at this scale, mine will remain closed and hence I have made them as one piece each side. I am currently fitting the protective bars. These are from 0.45mm brass rod and are spaced about 1.35mm between centres. Once glued I will trim them to length.

I then have to glaze them. I can use some plastic sheet I have, but I am not sure if I should try some of those thin glass plates used for making slides; of which I have a lot. Or is this asking for trouble as it will break sometime in the future. They are 0.1mm thick.

post-17393-0-39919300-1486576176_thumb.jpg

 

The difficult part here is making the strips with holes spaced to take the brass rod. I only have my Dremel drill press. I make the strips using a jig as shown below:

post-17393-0-68560000-1486576177_thumb.jpg

 

Everything is clean and firmly tightened. Also with a 0.5mm drill bit, it is mounted with only a short amount showing. Then a right angle piece of wood is clamped to the drill stand and the piece of wood to be drilled is stuck to a carrier with double sided tape. This is positioned such that the first hole to be drilled is in place when the carrier is in the corner. Then the drill is switched on and the first hole drilled, then a piece of wood is inserted between the carrier and the side of the right angle frame and the carrier pressed firmly up to it. Then the next hole is drilled. This process is then repeated until all required holes have been drilled. Taking care to drill each hole in the same way every time. Only once all holes have been drilled is the drill switched off.

To drill a second row I then remove all pieces from the end and add a piece of the required thickness at the front. Then repeat the above process. When they are this small and close, like this, I find about 2 in every 3 are useable.

 

Glenn

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

A brief update as I have finished my first sub assembly; the rear cabin. The following pictures are taken on 5mm graph paper.

post-17393-0-14001200-1486921709_thumb.jpgpost-17393-0-05883800-1486922315_thumb.jpg

 

The pictures of this in my last post convinced me that it did not look to bad, so I went back to it and completed it. The most difficult part was doing those slotted rails, even with the jig I made (see below). The dark ones are walnut and the light one is lime. These are difficult in the walnut as the small pips keep falling off. It is much easier and quicker to make these in lime. If this continues I may end up making all further strips in lime and staining them where required.

 

After failing to satisfactorily make these previously, this time a first built a jig. This has a slot for the wood strip and a profile for the wood to be removed. It then has a small notch which acts as a marker for the amount to move the strip on before cutting out the next notch. After cutting the first few notches I realised I needed something to stop the wood lifting as I cut the bottom. Hence the two pieces glued on top. I also found this made it much more difficult to push the strips through and hence there was less risk of them moving while making each notch.

 

post-17393-0-47577700-1486922319_thumb.jpg

 

It's now time to get back to the hull and finish that.

 

Glenn

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

  • 2 weeks later...

Coppering the hull.

It has been some time since my last update as I have started coppering the hull. Something I have not done before and felt I could not put off any longer. I first read all I could find on MSW on the subject. Unfortunately most of this did not relate to what to do with a 1m role of 100mm wide copper strip which is 0.05mm thick (2 thou). My guides for this are the plans from Musées de la Marine and the picture below.

p6-1.jpg.85e94948ea3b82ee5bf9007d195f3ff8.jpg

From this I decided that the copper plates on the model should be 35mm x 8mm. Working on my principal of using as much material as supplied in the kit as possible I started cutting the supplied sheet into the required plates. Once I had a few to work with I started trying out different patterns of indentations to represent the tacks that these are held on with. I finally settled on doing each plate by hand using the end of a sharp needle file to make each indentation at a spacing of about 1mm. I would put these along two sides and overlap the plates. Also these would be glued in place using CA adhesive.

 

It has occurred to me that as this ship was launched in 1932 and has been re-coppered fairly recently, the copper plates may not be attached in the same way as on a warship 200 years ago. However lacking any information on this I have proceeded in the assumption that they are still nailed in place.

 

This picture shows. In more detail, some of the plates prepared for the top band with rows of indentations on 3 sides. Below that is a cleat I am making. This goes on the bulwark stanchions, see later.

p6-3.jpg.d3cb6b0cabe174e54130a31b54ce1a1a.jpg

The next picture shows the stages of assembly, starting with a roll of copper strip, then cutting off 35mm lengths which are then cut into 8mm slices. These then have the nails embossed and are then stuck to the hull. All the tools I am using for this are also shown.

p6-2.JPG.4defb7a9e619e8cf1429f6918d5a5258.JPG

 

The first problem was plating around the propeller aperture which required many small plates cut specially to shape. This took a long time and I was not very happy with the way it looked close up. But from a distance, at least it covered everything. I did not think I would achieve much by pulling it all off and starting again. It might have been better to leave this to later when I have had some more practice, but as I am overlapping the planks it is where I have to start.

 

It was then fairly straight forward doing most of the rest of the plating on the first side. Though difficult not to get CA glue over everything, especially my fingers. I lost the line onece or twice but it is not too obvious. The main problem was I had to finish with a 2mm wide row before putting on the top band. My original plan had not included this. My overlap must have been a bit more than planned. There are 10 rows beneath this, so that is only 0.2mm extra overlap for each row.

 

For the second side I thought I would try a different method of gluing. At this point I have just started and am using some double sided tape I have. This is very sticky and holds very well. It seems ideal for the majority of panels that are flat, but does not work well with any that need to be bent, for instance those at the bow and along the keel. I am still using CA adhesive there. The problem is that using the double sided tape there is no movement possible. Each plate needs to be in the right place first time. I find in places like the bow and the keel I need some movement available to get the plate exactly where I want it.

 

As altogether there are about 400 plates, ignoring those around the propeller aperture, I am occasionally taking time out of the plating to do a few small jobs. I have added most of the points where rigging is attached to the poop deck.

p6-6.JPG.51c87b9fa16b30c64c1e1044d665e8f8.JPG

 

I have installed the chain plates, this picture shows those for the main mast. I spent a long time deliberating where these went and eventually decided they must be fitted to the inside of the bulwarks. The first 3 hidden by stanchions.

p6-5.JPG.c86b84bbd43fd892350041927338b433.JPG

Then I made these cleats, which are used to secure the sheets from the fore sails. Their positioning can be seen on the following picture of the real ship. Those supplied in the kit are small plastic things that look nothing like this. I will probably end up using some of the ones supplied, but not here when it is easy to make replacements.

p6-4.jpg.76aa8f95710a5427778a0f1bcbc1b702.jpgp6-7.jpg.9e79be6da07883caab43e73f0b210e5f.jpg

 

I will post another update when I have finished the coppering.

Glenn

 

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

  • 2 weeks later...

I have now finished the coppering and am quite pleased, at least with the second side. I still have the rudder to copper and to mount. I need to wait until I can get out and use my disk sander in the garage. I need this to taper the profile of the rudder and I am not allowed to use this in the house. This is the first time I have done this and I feel I learnt a great deal. I would like to think the next time I do this I will make a much better job.

p7-7.JPG.8e9c0e9d99280bbbcb850102f62f1b2b.JPG

 

As can be seen I have made the catheads and mounted them. The supplied instructions do not provide much help. Also the shrouds they supply are plastic mouldings, which I am replacing with wooden ones.

 

This was a bit of work deciding how to fix the shrouds. I think that in reality the bolts that hold these go through the cathead, which is made of metal, and then these bolts also act to attach the rear braces. In the end I decided to make these as 1 piece. I drilled a hole in the supplied cathead, I then put a loop in some 0.75mm brass wire which I threaded through this hole. Then when mounting this small assemble I shaped the wire as necessary to look like the rear braces.

 

To attach the shrouds I worked out what length of 0.5mm wire I needed to make a loop on the end and using a bit of string, what the length round the shroud is. I then formed the required fittings as shown below. The final bend was done using the shaft of a 3.5mm drill.

p7-4.jpg.e02d7dfbc0d99d16ad8bca61d172a785.jpgp7-5.jpg.b3a60c9bd60216584af83e30b161c96d.jpg

 

 

I then assembled these to the loops in the 0.75mm wire by using small brass planking nails as rivets and putting a blob of solder on to hold them in place. Now I have done these shrouds like this I have 20 more to do in a similar way for the shrouds that support the masts.

 

Here are some more pictures of the completed catheads. Eventually the lose end of each chain will be wound round a metal cleat attached to the centre of the extra wide stanchion where the cathead is mounted. Notice I have also mounted those cleats I made earlier. They have been pinned and glued in place.

 

p7-6.jpg.cf83c8fe9f6c02ed51a87df413e4b3c2.jpgp7-8.JPG.c05eeb71ab376700f36365ad781837ad.JPGp7-9.JPG.34ae5c7b37c34396febef6ef5b9adeae.JPG

 

I added the small rollers on the front of the catheads over which the anchor release chain passes.

 

I have no idea, when raising the anchor how it is brought back into the stored position on the cathead. There seems to be no tackle for this, though in one of the pictures below there is a ring shown on the bottom of the cathead whose purpose is unknown. This also shows the rear of the cathead where the braces are attached.

 

While I have been doing this I have been working out what eye rings, cleats etc. it is required to attach while the deck is clear making this easier. I have been doing drawings of the standing rigging and each sail showing associated attachment points for running rigging. One thing this has brought to light is that I do not know how the forward stay of the forward mast is set up. Looking in the following picture, a heavy steel rope can be seen descending from the forward mast masthead to the bow, the one that carries the staysail.

p7-3.thumb.jpg.52f0f5321edfeb67e27b46fb8c55afef.jpg

 

This seems to go into a brown ‘package’. In the next two pictures this can be seen a bit more clearly, though obscured by the sail. This in turn seems to be retained by a couple of metal bars attached to timbers mounted on top of the rails. Not sure what these timbers are called.

 

Is that it? In my eye they do not look nearly strong enough to take the strain of that heavy steel rope. Also is there something hidden in that brown stuff (leather?) that is used to tension this? Comments please.

p7-1.thumb.jpg.3a5d2be1ef60b2cc915ade122bdcff72.jpgp7-2.thumb.jpg.3ccbc958d7c8ef8614c3dd81b08d3f03.jpg

 

As suggested my next job is to fit any eye bolts, cleats etc. that can be identified and to fit the shrouds for the foremast and mainmast. After that I think it will be time to start fitting all the deck furniture I have been making.

 

Glenn

 

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

  • 2 weeks later...

A quick update to show I have not been idle since my last post.

Forward deckhouse

I have finished the forward deckhouse. This involved replacing the supplied ladder, leading to the roof, with one of my own manufacture. The picture below shows, from the left, the supplied ladder material, the one I made with some leftover 2mm * 0.5mm material supplied in the kit and the former I used to make this.

The steps for making the ladder were.

·        The rungs were all cut to 6.5mm length then inserted in the slits in the former, which were just made with a saw of the right thickness of cut. The former is about 1mm thinner than the length of the rungs, which therefore jut out slightly on each side.

·        This was then turned upside down and positioned on a flat surface and the rungs were all pushed down so they were flush with the surface.

·        The former was then turned on its side and pushed down so one end of each rung was flush with the former. The other ends are now clear of the former and a side piece can be glued in place without gluing anything to the former. This is done by turning it over so the rungs are again on a flat surface which is used to align the side piece.

·        Once this is set the first side piece is pushed in so that it is flush with the former and the other ends jut out. The second side piece is then glued in place.

p8-1.jpg.874b2fd700227d7a01af50d1a17532d2.jpg

And here it is in place along with a view of the real thing.

p8-2.jpg.42710c1a565f3b836b045afc34c703b3.jpgp8-3.jpg.fd78711219c0330ec8f57e13bdf53f90.jpg

I have just spotted the ships name and the inclinometer there. Maybe I am not quite finished yet. I will have to see if I can print something out for the name and make something for the inclinometer. Still, here are a couple of pictures of it so far.

p8-4.jpg.56c678e3a027995bc268705005f4832b.jpgp8-5.JPG.c43e2aa88d5b394bf1de80a0224c694f.JPG

Overview

The following two views show how I am getting on overall. The Hull is almost finished I have the rudder to make and a few other bits and pieces. This view makes me feel I am making some progress.

p8-6.jpg.5eaff3a1641993cd9bdd49b2fd86f75f.jpg

As for the deck furniture starting from the bow I need to finish the following, as shown in the picture below.

·        The chain winch.

·        4 storage boxes. Two of these go along the starboard side with the life rafts, one goes between the grand skylight and the companionway hood and the last by the machine hatch. I have started two of these which can be seen without their tops.

·        The companionway hood.

·        The machine hatch. Not sure if I am translating this correctly from the French. It might mean the engine hatch. It's directly in front of the main deckhouse

·        The main deckhouse.

·        The ships boat and davits.

And I thought I was getting close to finishing this stage and could start on the masts.

This picture shows all the deck furniture on a sketch of the deck. This is to scale and it is traced from the main plans and shows the positions of all the rings fitted to the deck to take blocks. I will fix this to the deck and drill through to get everything in the correct place. most of them cannot be seen in this picture, there are 24 blocks of 7 different types attached to the deck.

p8-7.jpg.05f3860a46e0213be6745b571a9dbc22.jpg

I could possibly include the bowsprit in this list as that will need to be in place to finish the deck.

Glenn

 

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

Glenn,

 

Just found your log. Excellent work indeed. Happy to follow along. Beautiful ship. It certainly helps to have photos of the original available.

 

PS: Your wood and metal skills are also very nice to look at.

 

Cheers,

Michael

Current buildSovereign of the Seas 1/78 Sergal

Under the table:

Golden Hind - C Mamoli    Oseberg - Billings 720 - Drakkar - Amati

Completed:   

Santa Maria-Mantua --

Vasa-Corel -

Santisima Trinidad cross section OcCre 1/90th

Gallery :    Santa Maria - Vasa

 

 

 

 

Link to comment
Share on other sites

Thank you for the complement and to all those who have given me likes.

 

Since my last update I have hung the rudder and made the bowsprit. I felt I needed a change from making deckhouses, skylights and suchlike.

 

Rudder

 

To hang the rudder I first had to make the gudgeons and the pintles. I had already decided I was not going to use the method suggested in the instructions which was only slightly better than bent nails and eye pins.

 

Unfortunately I become so engrossed in this I forgot to take any pictures of the process.

 

I first had to copper the rudder. Due to its shape this was not easy and the end result was very messy with CA glue everywhere. I have been trying to clean up any excess glue on the hull with acetone, but at this point I had been using some grade 0 wire wool for something else and decided to try that. This worked much better. It caught on a couple of corners which were not stuck properly, but this was quickly rectified. Very pleased with the result.

 

I have some 1.5mm outside diameter brass tube with an inside diameter of 0.75mm. I also have some 0.75mm brass wire. I cut six 1.5mm lengths of the tube. To cut the tube I first inserted the wire. This prevents the teeth of the jewellers saw catching when you break through to the inside. I insert this from the far end and make sure it is not flush with the end I am cutting. This just makes it easier to push out the small piece of wire left inside the tube.

 

I then cut some 1.5mm wide strips of 4 thou brass sheet. I just eye ball this as I cut this with scissors and know the blades are 2mm thick.

 

I then solder this together. I solder the 1.5mm sections of tube to the strip by first inserting the wire which then holds the small piece of tube in place while soldering. Three of these also need a bit of the wire soldered inside, which is no problem, but with the other three care is needed to ensure that the wire does not get soldered inside. This turned out to be easier than I thought. After this I trimmed the wire projecting from the 3 pieces it had been soldered to too 1.5mm. Then it is just a matter of cutting the brass strips to the correct length and assembling everything.

p9-1.JPG.cd2e2ede752db1d844a6830684bd8c4e.JPG

Bowsprit

 

The bowsprit came pre-shaped from Billings. It was a little thick but I decided to leave it as supplied. It then needed 3 eye bands and the martingale fitted. Billings supplied 1 brass ring with 4 holes for one of these and a chain plate which was meant to be used for another, with no instructions how this was to be used. It was not the correct length and the holes were in the wrong place and there was only 3 of them. For the 3rd I think it was just expected to fit eye pins to the bowsprit. I decided to make all 3 from scratch so they would at least look the same.

 

I first marked the position of the centre of each eye band on the bottom of the bowsprit. I then used the arrangement shown below to drill a hole for an eye pin in each of these positions.

p9-2.JPG.84d589761451d818b7d06342a553a0a4.JPG

To explain this, I have mounted the bowsprit in the chuck for my lathe. This has an adaptor, like a collet, with an 11.5 mm central hole. I have wrapped one end of the bowsprit in paper to make it a snug fit and then positioned it such that the positions of the holes I need to drill are aligned with the slots in the collet. I have then positioned the Dremel drill stand such that when it is pushed up hard against the front of the lathe stand (this view is from the rear) the drill is positioned on the centre line of the bowsprit. I then positioned the lathe chuck so that the holes to drill are along the top and can then be drilled by moving the drill stand along the front of the lathe. This picture was actually taken later in the process. Here is a closer view of the same thing.

p9-5.JPG.19e79a5eb2ed3afd3bd1ffe0164bb2d8.JPG

 

I then drilled the three holes along the bottom of the bowsprit.

 

Then I cut three small strips of paper, one for each eye band. I wrapped one of these round where each eye band will go, so the paper overlapped where each hole had been drilled and then pushed a pin through both layers of paper into the hole. I then cut some strips of brass with a width of 1.5mm from the 4 thou sheet and used the strips of paper as a template to drill two holes in each, one about 1mm from the end. I then wrapped these round the bowsprit and secured them using an eye pin in the holes just drilled, except for the inner one where I used the supplied martingale. I then trimmed the excess brass strip. It is best to leave this till now as it can be useful when securing the eye pin.

 

Finally after taking the assembly off the lathe I drilled another hole, by hand for an eye pin to secure the bobstay. Then fitted a bottlescrew and all required eye pins.. The bobstay is meant to be made from brass wire. Again no instructions on how to attach this to the bottlescrew or the cut water.

p9-3.JPG.efa9e97777b79a2c2774bb4fe125dc5e.JPG

p9-4.JPG.ad34c9d8be035ccd1cd9b7390eb6ead2.JPG

This is the first use I have made of my lathe for a number of years and I did not even have to plug it in. However I plan to use it to make the foremast and main mast. They both require tapering and holes drilled for cleats and such like. I will need some practice at spindle turning before I attempt that.

 

After doing all this I have just been looking through 'The Ship Model Builder's Assistant'; first published in 1926. This has a much superior way of making eye bands.

 

In my last post I gave a list of 6 jobs I still needed to do to complete the hull. I decided to rewrite this. I stopped at no 23, when I got to the bottom of the paper.

 

Glenn

 

 

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

Glenn, I'm happy to found this interesting and lovely build. You have some excellent detail work there, and the prototype is beautiful.

Link to comment
Share on other sites

  • 1 month later...

Eric, thanks for the comment. It defiantly makes a change to make a model of something that you can get photographs of.

 

It’s been some time since I was able to do an update. I have been busy with other things this month. As I have been unable to spend much time in the workshop I have been able to study the rigging plans, work out what needs to be done there and count how many blocks I need to make: 133. Though I think I might find a few more along the way. I have also drawn individual rigging plans for each sail.

 

I had decided to make my own blocks some time ago, as I am not happy with the plastic ones supplied (pictures curtesy of CMB website). They only supply 1 size and no triples at all.

f064-1.jpg.97c094e6da1f67b22e62b5787405fd0f.jpgf064-2.jpg.44b278f7396d9dac792faffb0e0544f8.jpg

I cannot find any commercial ones that do not have slots down the sides for a strap. Examples of the types of block I need are shown below. Incidentally I also need white rigging cord. I will probably end up ignoring the fact that some of the rigging is wire and some is chain.

p18-1.jpg.aaaadcb4d9a272c95a169e20ac76c595.jpgp18-2.jpg.3f9b6faf848925450d7cbd09c7669d12.jpgp18-3.jpg.7ffb158b33bb6bb33042a36a16e8647e.jpg

I am using boxwood to make the blocks. I bought a 3” branch many years ago and still have a small quantity left. The first job was to cut some small billets of different thicknesses for different sized blocks with either 1, 2 or 3 sheaves. In total I need

  • ·        small single                                47
  • ·        small double                                1
  • ·        medium single                           46
  • ·        medium double                          12
  • ·        medium triple                              3
  • ·        large single                                 2
  • ·        large double                                2
  • ·        large triple                                  2
  • ·        others                                       18

Small are about 2.5mm, medium about 4mm and large 5mm.

p18-4.JPG.3892a6397ce830cef2848e58f6557ca4.JPG

Then I made a jig for drilling. It looks a bit Heath Robinsonish but it works. It makes it easy to drill the holes in the right place and at the right angle.

p18-5.JPG.84330d8a726025af001b450ac6176cdd.JPG

The billets fit into the slots and once pushed home a hole is drilled. I use a pin vice as the jig is only wood and if I use a power drill I find it opens up the hole quite quickly. I then shape the block and do anything else required while the block is on the end of the billet. I am adding a small strap to one end, which can just been seen below on the bottom billet. Some require a hook instead.

p18-6.JPG.caadf19c361e17af3bec9e80a8d03c68.JPG

Then I saw off the completed block and it’s on to the next. I should get about 20 from each strip.

 

I have made 20 so far of various sizes. I am improving; getting faster and they are becoming more symmetric. The most difficult and time consuming part is fixing on the small half strap with CA adhesive.

 

They are not exactly like the real thing but I do not see how I could make the strap internal at this small size. As a final step some then require an eye-pin in the free end; so they can become half of a tackle.

 

The thing about this is that even though I have little time at the present and will not have much time until the end of the month, it is possible to sneak off for 1/2 hour occasionally and make a few blocks. Hopefully by the time I get back into the workshop on a more regular basis I will have got most of the blocks I need.

 

Head decoration

 

Another task I have completed is the head decoration. I had a go at carving this earlier from a single block, without any success. This time I built it up from 3 pieces and am fairly happy with the result.

p18-7.JPG.2f6c791659d67e10542023983e080127.JPG

Note, I have also stained the bowsprit, which was something I realised I had forgotten about before mounting all the metalwork.

 

My next main task is to start permanently mounting all the deck furniture I have made. This will be possible as I will be able to mount the required blocks on the deck at the same time, which would otherwise be very difficult if I had to work around all the other stuff.

 

Glenn

 

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

  • 4 weeks later...

 

It is some time since I posted an update; as I said I have been busy with other things. However , during this period I have been making some of the required blocks. I have now made about 40 and have the process well worked out. I will now probably just make them to replace the ones I use. I can do the singles fairly quickly and that is the majority.

 

I have started mounting the deck furniture at the stern and the bow. The stern is shown in the following two pictures. If you look carefully you can spot some of the blocks.

p15-1-1200.thumb.JPG.bfe363e592c428a25eedaf63536328d8.JPG

p15-2-1200.thumb.JPG.8e7b58a650daa71558fa103539203905.JPG

The stanchions are just pushed into the predrilled holes. These are replacements for the kit supplied ones which only had provision for one rail. I had made a little jig, with a pilot hole, that hooked over the side and ensured the holes were drilled upright and in the right place. When pressed firmly against the side the hole would be the right distance in and a mark on the jig ensured that the correct position along the side could be easily set. This was thick enough to ensure the hole would be drilled vertically.

 

When I was pushing the stanchions into place, for this picture I realised I had only drilled one side and as the jig had just been made for the task it had been discarded. However I never throw anything like this away and I eventually found it in a box of small bits of scrap wood. Phew.

 

In the bow, so far, I have mounted the bowsprit, the chain gear and the bollards. The chain gear having been made from scratch to replace that supplied in the kit, which was out of date for the period I am modelling. My intention was to rig the bowsprit, but then I realised that I needed 3 bottlescrews, which I do not have. I am now waiting for them and a few other bits and pieces to arrive from Cornwall model boats.

p15-3-1200.thumb.JPG.9c9840ce0a576dc5882613f2fcadc1cb.JPG

p15-4-1200.thumb.JPG.4dbaceef6f1d88b3e626f60ece93028e.JPG

Some time ago I had ordered some Caldercraft stud link anchor chain, to replace the ordinary chain supplied in the kit. I blackened this with Carrs products. I first cleaned it in Acidip, then used Metal Black and finally Electrofix. I then threaded this chain in a loop through both sides of the chain winch, the chain stoppers and the Hawse holes and then mounted these on the deck cutting off the excess chain from underneath the winch, where it is secured.

 

This means that at present a length of chain just loops round from one side to the other. It will be left like that until it is time to hang the anchors, which is some way off.

 

The bollards were more of a problem than the chain. The metal black did not work as well, it left a bright brass circle where each bollard fitted into the base plate. All I can think of is there may have been some residual flux from the soldering. I used Caldercraft Matt (Metal) Black paint to touch these up. I really recommend this for metal, it is very effective.

 

I have also started work on both the central companionway hatch and the machine hatch. But as neither is finished I will leave them to my next update.

 

Thanks to everyone that has given me a like,

 

Glenn

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

A quick update. I have finished mounting all permanent fixtures to the deck forward of the foremast. Before I progress further I want to make the fore mast and check its fit.

p19a.thumb.JPG.276589b7dd7ba2791720fa3cf9801083.JPG

The bottlescrews arrived so I have progressed with rigging the bowsprit. It was a lot of effort to make those chains look tight. Either they hung down or if I removed 1 link they did not reach. Eventually I had to stretch the fitting at the bottom of the martingale.

p19b.thumb.JPG.ca169f40800a1f403a01cbf849a1aebc.JPG

But I did not get very far. The rest of the rigging on the bowsprit needs to simulate steel cable. This is a problem I have been pondering for some time along with the rest of the rigging which uses rope made from synthetic fibres and is white in colour.

 

I have been trying different materials. I tried some 7 strand 0.4mm steel cable, unfortunately this would not bend tightly enough to look correct at each end though it was fabulous in between. I did find a cable made out of copper finished to look like steel (sold for AFV towing cables), but it was sold in only short lengths and the total cost was prohibitive. That leaves using light grey rigging cord to simulate steel cable. So finishing rigging the bowsprit will have to wait until I make some. I had already decided that I would need to make white rigging cord for the synthetic rope. I need to make a ropewalk.

 

The other problem here is fixing the Bobstay. The Instructions show a length of brass rod with one end attached to the bottlescrew on the bowsprit next to the martingale and the other end fixed to the cutwater with a bent chain plate. They give no clues on how this might actually be achieved. Especially attaching the brass wire to the bottlescrew.

 

If we look at the real thing: we see that the end of the bottlescrew is forked and the bobstay ends in such a way that it can be attached with a bolt. I should be able to replicate something like that. In the cutwater there is a triangular bracket which probably works in the same way. I think I can make one of these from a bit of 4mm brass I have from the old type radar system included in the kit, which was mounted on the deck and is replaced by a mast mounted system in the period I am building. So I will give that a go.

p19d.thumb.jpg.553178e1d0eeb5a238e7dd904ca2df3b.jpg

That should keep me busy some time.

 

Glenn

 

 

 

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

Glenn,

 

Just catching up. Excellent work indeed. You set the bar very high!! - always a pleasure and learning experience when I visit your build log.

 

PS: Might be "off timing" for you but Chuck (Syrene) is now stocking excellent new types of blocks.

 

Cheers,

508621253.jpg.01a61ddacb95f652af9993f758af9850.jpg

Michael

Current buildSovereign of the Seas 1/78 Sergal

Under the table:

Golden Hind - C Mamoli    Oseberg - Billings 720 - Drakkar - Amati

Completed:   

Santa Maria-Mantua --

Vasa-Corel -

Santisima Trinidad cross section OcCre 1/90th

Gallery :    Santa Maria - Vasa

 

 

 

 

Link to comment
Share on other sites

Thanks for pointing out chucks new blocks, I had spotted them myself, for the larger blocks they look really good, exactly what is needed. However he does not make them small enough for most of my requirements. I am not sure of his sizes, I think his smallest is 3/16" (4.5mm). Most of what I need are 2mm (1/12") and 3mm (1/8").

 

I do like the way he has inserted the metal strips and even doing two strips on the double block. I did think of doing a layered design, but I did not have any suitable wood and there would have been too much waste to saw the boxwood into 0.5mm strips.

 

Thanks also for your other comments, I have been keeping my eye on your Wasa, a stunning build, I have not commented myself as so many others do. I was in Stockholm about 25 years ago on business and the person I was working with took me to see the ship. Fantastic.

 

Glenn

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

Glenn,

 

I sort of thought that Chuck's blocks may be a tad too large.

Thanks as well for your kind words regarding my current build. When I was working in London in the mid-90's I took a long weekend to go see the Vasa. Yes amazing to see indeed. 

 

I had asked my son (then 12 to also come along) he declined. When he visits us now, and looks at how my build is going - he says the he regrets not having gone to the museum as well.

 

Cheers, 

Michael

Current buildSovereign of the Seas 1/78 Sergal

Under the table:

Golden Hind - C Mamoli    Oseberg - Billings 720 - Drakkar - Amati

Completed:   

Santa Maria-Mantua --

Vasa-Corel -

Santisima Trinidad cross section OcCre 1/90th

Gallery :    Santa Maria - Vasa

 

 

 

 

Link to comment
Share on other sites

Michael,

 

I guessed you had gone to see it. I could not imaging putting in all the effort you have in your build without ever having seen it. I have been trying to see if it is possible to visit either the Etoile or the Belle Poule, its sister ship, but there does not seem to be much information on their movements. Maybe because they are French navy.

 

On with the build.

 

I have completed the bobstay. I was pleased that my plan for this worked. Here is what I started with:

  • A short bit of 2mm x 4mm brass not required.
  • 0.75mm brass rod
  • 1.5mm brass tube with 0.75 inside diameter.
  • The bottle screw.

The following image shows these pieces slightly later in the game.

p20a.thumb.JPG.e205051b26d09d4be614586e7b23503a.JPG

The bottlescrew supplied had ring ends. I converted one of these to a forked end while still leaving a hole in each of the two forks. This was done by first cutting a slot using a jeweller’s saw, then enlarging the slot with a cutting disk in the Dremel and finally a needle file. I cut the slot with the saw first to act as a guide for the Dremel.

 

I then used a centre punch to mark the position for a hole near one corner of the piece of brass. This was about 1mm in from each edge, then I drilled this with a 0.8mm drill. I also scribed a line at 45 degrees from the adjacent corner as can be seen.

 

I then cut a slot in this corner using the Dremel in a drill stand. This had to be deep enough to take the bobstay, but still leave some metal before the line. It was required that this slot was wider than the thickness of the Dremel cutting tool. To achieve this I adjusted the height carefully so that it was off centre then after 1 cut I turned the brass piece over and repeated the cut. This was done by eye.

p20b.thumb.JPG.9568935ad24db7890ce094ede33ed411.JPG

I later used the jewellers saw to cut this piece off along the scribed line.

 

Then for the bobstay. I first cleaned up the ends of the rod and the tube and positioned them as shown below, at right angles poking over the edge of the table. I then soldered these together.

 

p20c.thumb.JPG.a13bf6817d4eac98220c325421438f58.JPG

p20d.thumb.JPG.4f4a2ee6e4ba7f7c0f481b096bb8b3ca.JPG

Then again using the jewellers saw I cut off the end of the tube soldered to the rod. To prevent the teeth catching when I break through to the inside of the tube I slide a bit of rod inside. I then cleaned this up and tested the fit with the previously made parts.

p20e.JPG.b1a1f361afdcf39beb5a13aaf38ce20b.JPG

Not sure about including that last picture it looks awful at this size - must be before I cleaned it up:)

p20f.thumb.JPG.10f614d7b71359d1853699df7fbc13e9.JPGp20g.thumb.JPG.6befaac1fd4c084f29c2cf54bf1c90fd.JPG

 

I then needed to measure the length required I found it easiest to fit it to the triangular piece and measure to the bobstay, the result was the rod needed to be 92mm long. I realised that any slight error would just result in the triangular piece ending up slightly offset from where it should be. Probably by an unnoticeable amount.

 

Having cut the rod to the correct length I repeated the process of soldering the tube to the other end and cutting it off. Unfortunately, in my excitement, I forgot to take a picture of this before it was fitted.

 

Having got to this stage, it was then only required to replace the bottlescrew on its fitting behind the martingale, attach the triangle to one end of the bobstay and the other end to the bottlescrew. In both cases using a nail as a bolt, secured by a small drop of CA adhesive. Then using CA adhesive fix the triangular bit to the cutwater.

p20h.thumb.JPG.90caadbdfdb2b685c7efd8709c6ba931.JPG

p20j.thumb.JPG.c868b4bbbdb31e6bc71c7e6646e76568.JPG

At this point I have to admit I dropped the triangular bit when attaching it to the bob stay and could not find it, so the one used is the second attempt. I am quite pleased with the result. You never know what you can do until you try. I had been thinking about this for some time.

 

Hopefully tomorrow will be 'make a ropewalk day'.

 

Glenn

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

  • 2 weeks later...

Thanks to everyone who has made a comment, given a like or just looked in. As it’s been a few days since my last post I thought I would do a quick update.

 

I will start with the subject of ropewalks. I made one and I made some rope, but I was not happy with it; the rope was inconsistent. I am pretty sure that this was because I could not get a ball bearing swivel for the looper and the non-ball bearing one I could obtain locally was just not up to the job; it did not turn smoothly. I now have the required part on order and am awaiting delivery. So I will leave the subject of rope walks for the moment and move on.

 

As I am stuck with finishing rigging the bowsprit and I have now installed everything on the deck forward of the foremast, I thought it is now time to start on the masts, in particular the foremast. This is what it is needed to make. Though as I will use the supplied piece of 8mm dowel, my version will not be an accurate representation.

p21f.jpg.9822e326519697080edac7c9bb93a6c0.jpgp21g.jpg.8818e0ccba12f79ee00887bdb4a5b199.jpg

As this is different from the version supplied in the kit I drew some plans. At the top is the foremast top, drawn correctly. Then beneath that sketches of the mainmast top. Basically the mainmast top is the same as the foremast top except both spreaders are the same length, there are no topmast backstay spreaders and there is a radome mounted forward. I took relative dimensions from the photograph and assumed some dimensions would be unaltered to obtain a reference.

p21h.thumb.jpg.a3ab21694d9f17c7f882950064c996dd.jpg

Here, on the left, is what is supplied in the kit, except for the length of 8mm dowel which I will leave to your imagination. Considering the kit parts are plastic mouldings all of the spreaders are different lengths. The difference between the longest and the shortest is 2mm (10%).

 

Next to this is my version made from some Basswood I managed to pick up. As I am in the UK it is more normal to find Lime, but as it states on the packaging 'Made in USA', I guess it is really Basswood. Having used it, the only difference I found is that it is white, where lime tends to yellow. It makes me wonder if some of the wood I have bought in the past as Lime is really Basswood.

p21b.JPG.71b9ca4351567734eb3b4e6e526a0638.JPG

My version is made of 5 parts.

p21a.JPG.a7279c0295794a55b997fd5ff6118fb4.JPG

I was going to try and make the spreaders for the rear stays out of brass, but I have decided I just do not have the tools for this, unless I whittle them from solid brass. So they will be wood, but given the chances of them getting broken I will leave off making and fitting them for the moment.

 

The assembled mast looks like this. The cheeks are from some 1mm x 10mm lime I have. I cut 4 pieces to the correct length and clamped them between 2 of the supplied plastic pieces. I then cut them out carefully with a jewellers saw and finished them with sandpaper. Things are really easy when a template is supplied.

p21d.JPG.80b3e58caf9376f680c7f2720124b784.JPG

And in situ.

p21e.thumb.JPG.b3a84f3f37f2cf964aae0df1082638ce.JPG

Now for some metalwork. It needs a few holes. This time I am using the indexing ring to space out holes for cleats at 45 degrees. I am also using the tool rest to support the mast. The square is being used to set the initial position using the side of the top.

p21c.JPG.60b740b1214a6b09c5284d1dbc28726c.JPG

That’s as far as I have got. Hopefully I will get a chance to finish this in the next few days

 

Glenn

 

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

The next step was to stain the mast burgundy, like the bowsprit, then give it a quick rub down. I then fixed a brass band just beneath the cheeks, with an eye pin inserted each side. At this stage I had forgotten about the truss for the yard and had to drill and fit that later.

 

The futtock shrouds are then made from 0.5mm brass rod. Round nosed pliers were used to form an eye at one end. Then the distance from the eye pin on the mast to the spreader was measured and using small pliers the rod was bent this far in from the eye. Then from experience I know that an eye in rod this thick uses 4.5mm of material and the spreader is 2mm thick. Therefore the rod was cut off 6.5mm from the bend. This was then inserted through the hole in the end of the spreader and another eye formed on the working end. It took a couple of hours to do all 4 which surprised me.

 

Note the half circular cut out just behind the square hole. Keep this in mind for a future post, all will be explained.

p22a.thumb.JPG.1e5749025ea6e796ce855242535c30bc.JPG

Then using the same brass rod I made up 4 of these for the deadeyes. This is done in a similar way. Make an eye on the end of the rod. Then cut this off the rod 16mm from the eye, 11.5mm to go round the deadeye and 4.5mm for the eye at the other end. Make the eye on the other end and then bend each eye back at a right angle, finally form it round a drill shaft.

p22b.jpg.8125ae5a5a04ff9c97b5458ba2b1ed73.jpg

This is then all assembled using brass nails. Here is an example of how I solder these in place.

p22c.thumb.JPG.b7301550fb362e7297e6083e115a3a4d.JPG

 

The cross over tweezers hold it all in position while solder is applied to the side opposite the head of the nail to solder the nail to the eye on that side. Fixing the futtock shrouds to the eye on each side of the mast was done similarly. It is really a matter of improvising something that works to hold the pieces together on a case by case basis.

 

Those with keen eyes will notice a row of 5 holes drilled in the mast head. There should only be 3, I got the spacing wrong. Of the two in the wrong place, one will be covered by a brace for the fore stay and I will fill the other before touching up the staining.

 

The alternative is to put an extra eye pin in the hole, there are always ones not being used in the rigging. For instance in pictures of the ship I can see a eye bolt under the rear port spreader with a pendant hanging from it. I have no idea what this is for as I have been unable to follow the rigging any further than the block on the pendant. It’s not in any rigging plan I have.

p22d.thumb.JPG.04cbb4edc02cb01675e3bb83ec327d9a.JPG

I have now done about as much work as I can on the forward mast before actually mounting it, most eye pins will not be mounted until I can do so with the appropriate block or other fitting attached, so I had a dummy run.

 

I have checked the waterline is correct forward-aft simply by measuring and port-starboard by using a spirit level. I then suspended a plumb line from the rear of the mast. When the mast is in the correct position this will fall 15mm behind the bottom of the mast. This ran smoothly, there is a little wiggle room for the mast, but it is easy to get it in the correct position and when it is it looks correctly aligned when sighted along with the bowsprit.

p22e.thumb.JPG.18a2e094df687bff6718826e30359043.JPG

However, now its all fitted together, I noticed that in position the mast hoops look very thick. So I took them off and measured them and found they are 2.5mm, at 1/50 scale about 5” on the real thing. I used rough sandpaper to reduce this to about 1mm. They look much better, but I do not have a picture yet.

p22f.thumb.JPG.7d1fb5687ca141c2500c023c12512fc5.JPG

The only other work required was to fit something to hold the boom. This is 2 brass bands 6mm apart with an eye pin in the aft side of each and a brace between the 2 opposite. When it comes time to fit the boom it will be supported by a pin pushed into the 2 eye pins, which will then be able to move from side to side. sorry for the poor quality of this picture.

p22g.JPG.b7c73b22e57757fb9cbb3fed57988b0e.JPG

However I have found a new source of pictures of the real thing. Each of the schooners has a Facebook page. I am not a great user of social media, hence it taking this long for me to find it. There are a lot of pictures of the last rebuild of the Belle Poule. I especially liked this one. How many different blocks do you have on your model?

p22h.thumb.jpg.18e3dde26ea40d2b44c7f74c41bd1cd4.jpg

In my day you had to have done something naughty to get a job like this.

p22i.thumb.jpg.0418b2a5b6a4adc1071c1e927f0aeaab.jpg

Hope you enjoyed that. Again thanks to all those following and posting likes. It is encouraging.

 

Glenn

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

Things are going slowly at present. I am being held up by the lack of the right coloured rigging cord; with the appearance of steel rope. The bit I need for my rope walk has not arrived. I checked up on Amazon and discovered that delivery is 1 month. I did not bother to check when I ordered, I just assume anything I order from Amazon arrives before I log off. This means I am trying to get on with some of those tasks I have been putting off. Normally I put off something because I am not sure what is required, how to do it, or I am not sure how much I can include at this scale.

 

One of these problems was exactly how the top masts are mounted. With the new pictures I have obtained I have now solved this.

 

You can see in this picture that the top mast is offset from the square hole in the top. Also from a picture I posted in my last post, of the mast lying on the ground, that hole is just too far forward. It is there for the top mast to be raised through when it is stepped. But if that is all it was for why bother?

28a.jpg.f4744e8fc4c1ffbe3d446aa2567656ca.jpg

It is also possible to see that the top mast is square at the bottom. Something that the supplied part is not. My assumption at this point was that the top mast sits on the top just back from the hole overlapping it and a block of wood is fitted into the hole. But then how is the mast held in place? The answer is simple.

28b.jpg.2d66db7dfb120fc11108d23423b157e4.jpg

It can be seen in this picture that there is a block in the hole, and in the next picture that the bottom of the top mast is not square. It has been cut so there is a lip that rests on the head with the section below in the square hole. Then once a block is knocked in to fill the hole the mast is held securely in place. Also in the first picture, a slot can be seen near the bottom of the mast. I have wondered what that is for. In the picture below it looks like the rope used to raise the mast into position goes through it.

28c.thumb.jpg.24c26371900f084df06b8541ff46510b.jpg

I have now fitted a square section to the bottom of the supplied mast. I first drilled a 2mm hole in both bits and strengthened the joint with some bamboo. I then shaped the square section as required. This also had the effect of lengthening the top mast by about 9mm, which was useful as the supplied part was about 6mm too short.

 

Going back to my previous post where I pointed out the half circular cut out just behind the square hole. This was where the round version of the top mast sat. I have now enlarged this to make it rectangular so the square bottom of the new top mast sits snuggly in it, with a section going down through the square hole.

28d.thumb.JPG.c44e716a922606a109e4077480200871.JPG

Its only dropped in place in this picture, it goes  closer to the fore mast giving a more realistic gap. Now when I mount the top mast permanently I will insert a small block to fill the rest of the hole. Problem solved. I hope that once stained the difference in materials will be hidden.

 

To divert slightly. How do you lift one of these?

28e.jpg.caac280582effd6501b17d99fc376f3c.jpg

Answer, with one of these.28f.jpg.60ab7bcfd78401b9cd6553538e6a05e1.jpg

28g.jpg.e7a0ac6c7ee5a7b6c0fabf4df31f67e5.jpg

Glenn

 

Current Builds

Scottish Maid, V108 Torpedo boat

 

Future Builds

Snake (Caldercraft)

 

Previous builds

HMS Shark (Sergal), Sirene (Coral), Armed Pinnace (Panart), Etoile Schooner (Billings)

Link to comment
Share on other sites

awesome looking ship Glenn......the model is very well done.

I yam wot I yam!

finished builds:
Billings Nordkap 476 / Billings Cux 87 / Billings Mary Ann / Billings AmericA - reissue
Billings Regina - bashed into the Susan A / Andrea Gail 1:20 - semi scratch w/ Billing instructions
M&M Fun Ship - semi scratch build / Gundalow - scratch build / Jeanne D'Arc - Heller
Phylly C & Denny-Zen - the Lobsie twins - bashed & semi scratch dual build

Billing T78 Norden

 

in dry dock:
Billing's Gothenborg 1:100 / Billing's Boulogne Etaples 1:20
Billing's Half Moon 1:40 - some scratch required
Revell U.S.S. United States 1:96 - plastic/ wood modified / Academy Titanic 1:400
Trawler Syborn - semi scratch / Holiday Harbor dual build - semi scratch

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...