Jump to content

russ

Members
 View Profile  See their activity

  • Posts

    3,086

  • Joined

  • Last visited

 Content Type 

Everything posted by russ

  1. russ
    John: Your build looks good so far. The hard work here will pay off down the line. Russ
  2. russ
    Bob: I always enjoy watching the careful, tedious work that will eventually make the rest of the model look so good. No one sees these steps in the finished model, but they are there and it is what makes the difference. Good work. Russ
  3. russ
    Rob: Very nice work. I like the various hull forms, especially the bottom most one in the last photograph. What ship is that, if you do not mind? I have also built small half models and they can be a lot of fun to build. Russ
  4. russ
    I am sure this has been done a number of different ways even down here and I am still learning about how everything works on these vessels. I am fortunate to have a few people who have been kind enough to talk about it. I am always learning something new on this project and that is never a bad thing. Russ
  5. russ
    John: Here they used the boards in the brackets to secure the tarps. It was usually a regular 2x4 board that fit into the brackets on each side of the hatch coaming. Russ
  6. russ
    Thanks. The tarp is pulled over the hatch and boards are placed over the tarps along the sides and into to the brackets for a snug fit. When the boards are in place over the tarps and into the brackets on all four sides, the tarp is secure. Russ
  7. russ
    Bob: They sell them in 1", 2", and 3". The price does seem dear, but they will always be correct and that is something to think about. It may be that they can gotten elsewhere for less though, so it pays to shop around. Russ
  8. russ
    Often times, any level of gloss on a model does not look good. The real ship might have had some gloss in it, but gloss tends not to translate well through the smaller scale of the model. Russ
  9. russ
    Here are the brackets on the side of the hatch coaming and how they were made. The actual brackets on these lugger hatches is made from two pieces and I have created my own two piece method to get these results. Once they are painted along with the rest of the coaming, it should look okay. I have one more bracket to fit on the forward side of the coaming. Russ
  10. russ
    You can get those from Micromark, but probably from a hardware store as well. https://www.micromark.com/2-x-2-x-2-Inch-Angle-Plate Russ
  11. russ
    John: I see the progress quite clearly. The fairing is coming along. The inside fairing looks very good right now, but I have no doubt that you will work it a bit closer as well. I am looking forward to seeing this hull planked. So far the lines are shaping up nicely. Russ
  12. russ
    Mark: You are doing very good work. I hope one day to approach this level of skill. Like the others, I have my scrap box, full of fond wishes that did not quite come true. It is indeed a special occasion when I get something right the first time. Most of my models are full of second, third, and fourth tries. Russ
  13. russ
    This looks very good so far. You did nice job with the deck planking. This is a nice old kit. I had fun building it back in the day. Russ
  14. russ
    Mike: The blue is pleasing enough, but beyond that, I really cannot say anything useful. I am not that familiar with the period colors for that region, but if you are happy with it, then I say go for it. The pastel color is probably appropriate. I have a Hobby Lobby near me where I get my paints and in this case, I would buy a few different variations and then run some tests to see what looked best. Russ
  15. russ
    Pat: Very nice paint work and coppering. This is a beautiful hull form. Great work. Russ
  16. russ
    Mike: Your model is coming along wonderfully. Very nice details. You might consider doing a mock up of the side planking using both colors to get a better idea. Just glue up several pieces of scrap planking on a piece of scrap wood and then paint the two colors on to see what you think. Russ
  17. russ
    Pat: Thanks. I have actually found a better way to make those small brackets on the side of the coaming. Shockingly, it is better and easier to make them out of two pieces, the way they were actually made. Go figure. Russ
  18. russ
    John: Thanks. It is surprising how much research has to go into what seem the smallest details. Carl: Thanks. The width of the first three hatch covers are 33 inches wide and the last one is 30 inches wide. Russ
  19. russ
    The hatch covers have been completed except for paint. I am also making the brackets for the planks that would hold the tarpaulin cover in place. There are two on each side of the hatch and the ends. I am going to live with these for a few days and see what I think of them. They may be replaced, but we will see. Russ
  20. russ
    Pavel: You should really fit the false deck and then plank it. It would be far more difficult to bend the planked deck in both directions if you plank the false deck before fitting it. Russ
  21. russ
    Sam: The masts, shrouds, and ratlines all look really good. Very nice details on the futtock shrouds. Russ
  22. russ
    Sam: Thanks. I appreciate it. Russ
  23. russ
    Eric: You should consider bracing the bulkheads to keep them square while the glue sets. Maybe clamp a machinist's square to the former to hold the bulkhead square while the glue dries. You could use a scrap wood block as well. Just something that square that you can clamp to both the bulkhead and the former to keep them square while the glue dries. After the bulkheads are glued in and the glue has dried hard, definitely glue filler blocks in between the bulkheads to help stiffen the hull. I would glue them in closer to the outside of the hull because that is where the most stress will be as you work on the hull. However, you could use blocks that are glued to the former and the bulkheads. The main thing is stiffen the bulkheads. As for beveling the bulkheads, if you can lay out the bevels on the bulkheads accurately then you can do some beveling before gluing them in, but I would not try to do it all. Always take off less than you think you should. It is easier to remove a little more but it is difficult to put it back on. Once the bulkheads are glued in and everything is nice and stiff, then you can do the final beveling. That is why those stiffeners between the bulkheads will come in so handy. Hope this helps. Russ
  24. russ
    Ken: 1/32 scale actually comes out to 3/8" = 1'. Good luck with the build. THis sounds like a scratch build rather than a kit build. Russ
  25. russ
    Pat: Thanks. I always enjoy a good jig. Russ

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...