Jump to content
MSW Spring Donation Drive

allanyed

NRG Member
 View Profile  See their activity

  • Posts

    8,149

  • Joined

  • Last visited

 Content Type 

Everything posted by allanyed

  1. allanyed
    VERY interesting. What a great find!! Allan
  2. allanyed
    Phil Are you asking about for the Revenge 1577, or later, 1652, 1654 or 1699? Not sure it matters, but I am also curious to see an answer based on contemporary sources. Allan
  3. allanyed
    Depends. For the magazines there were light rooms that sealed off the actual light source from the magazine. For the Fly 1776 you can see one on the internal profile drawing. https://www.rmg.co.uk/collections/objects/rmgc-object-84458 For the gundecks the tin lantern from the Victory may help. https://www.sothebys.com/en/buy/auction/2022/treasures-2/a-painted-tin-and-horn-lantern-from-the-gun-decks It looks a lot like the one in the photo you posted. Hope this helps Allan
  4. allanyed
    Thanks Toni, I looked in every logical book that I have except my own! Thanks again. Allan
  5. allanyed
    Noticed the same thing Mark and the running line is tarred. I figured it was just a test set up. Good point though. Glenn, beautiful work and thanks for posting the photos. I wonder though about the second photo in post #1. I always thought there would be an eye, with or without a thimble, rather than the line being forced under the strop around the block. (Right side of the photo) Allan
  6. allanyed
    Are you speaking about the shape of the waterway? (outboard most piece) Depending which ship, era, nationality and deck, the planking may very well have been done as shown on the following rough sketch. Allan
  7. allanyed
    AH100 and Eberhard With all these small wire sizes, there is no reason to be overscale up to about 1:200 but I cannot imagine making rings at that scale. With these old eyes, I would want to work under a microscope!! Allan
  8. allanyed
    I like to use this method as well in a number of situations. I have used an iron and hair dryer but find a hot air gun from the hardware store to be easier than a hair dryer or an iron. It gets hot enough to burn wood at the highest control setting so I go to just under that setting and it works really well and quickly. In the end, whatever works is a good way to go and it is nice when we have choices. Allan
  9. allanyed
    What ship/year/nationality? I scoured my books but cannot find a chart so far on the chain link diameters for various size deadeyes, etc, but the following pic from RMG may help you. If the below deadeye was 12" real world the link material diameter would be ABOUT 1.25" so at a scale of 1:85, the diameter of the wire for the links would be about 26 or 27 gage. Give consideration to the shape and lengths of the chain plates as they varied quite a bit as well as the number links when the width of the channels changed a lot around the end of the 17th century and the channels were raised by a deck in the early 18th century. Allan
  10. allanyed
    Hi Shipman Just do not use it for ships built from 1670 through 1710 as Danny used his own formula and it is useless for those years. Otherwise it is good to go as it is an easy version of the David Lees formulas used in The Masting and Rigging of English Ships of War, 1625-1860. Go to the articles database in the upper ribbon here at MSW or just click --> https://thenrg.org/resource/articles and scroll down to the spreadsheet by Danny Vadas in the Masting and Rigging section, then click on it and it will open. Allan
  11. allanyed
    K, For blocks and deadeye, it as Keith posted. What ship/year/nation? Blocks are sized for the line size which is based on a formula involving mast size, hull size and so on. It is not as hard as it sounds as there is a spread sheet here at MSW that will crank out everything you need once you put in the few initial figures. Same goes for cannon and ship's boats. It depends on the nation, size of the ship and era. If you can indicate which ship, the answers to your questions are not really that difficult to find. Bells varied a bit as well and I for one would love to know if there was a regulation in the past for various nations as there has been for U.S. Coast Guard regs in recent years: §83.33 Equipment for Sound Signals (Rule 33) Allan
  12. allanyed
    I agree Syren makes beautiful things, including the carriages. It is hard to tell from the photo but the brackets look like they are parallel rather than angled as in the drawing below. From Volume 2 of The History of English Sea Ordnance, by Adrian Caruana, page 373. There are a number of other examples in the book as well. Allan
  13. allanyed
    Do you know if they make it in smaller diameters? 0.011 is too large for some rings for scales of 1:64 or smaller. Copper comes in smaller sizes and is easy to solder (soft or silver bearing) and can be blackened with liver of sulfur or painted once cleaned up. Allan
  14. allanyed
    CH Did you follow up on the responses to this same question that you posted two days ago or do any research of this topic here at MSW? If you use the search box for joggling you will get 9 pages of posts on the subject. Allan
  15. allanyed
    Ten down, forty to go. Don't even THINK about retiring Chuck, you will disappoint a LOT of folks out there. Congrats!
  16. allanyed
    Hi Clovehitch Do you mean joggling? There are a number of posts here at MSW on joggling the deck planking including (https://modelshipworld.com/topic/21231-uss-syren-1803-by-overworked724-–-model-shipways-–-scale-164/page/16/#comment-791103) as well as detailed drawings in volume I of the Fully Framed Model and The Construction and Fitting of the English Man of War to name two. Allan
  17. allanyed
    Clovehitch You will KNOT be disappointed for joining the fray here at MSW Welcome Allan
  18. allanyed
    The drawings show a platform aft that sits about 15 inches above the keel. Hard to tell if that is the case in your photo. That gives room for the davit chocks that hold the pivot rod beneath the aft platform. There would be a rectangular hole in the aft platform that is large enough for the davit to go through to the rod. Your model is exceptional Craig, kudos!! Allan
  19. allanyed
    Kevin, PMing you. THANK YOU Allan
  20. allanyed
    Copper wound around a drill bit as mentioned then cut with scalpel or chisel as also mentioned. Holding the ring with tweezers and using low temp silver solder paste works beautifully. I have been using Solder It Silver Bearing paste which melts at 450F (232C) with great success. A tiny dot of the paste is all that is needed especially with #33 gage copper which would be 1/2" at 1:64. Allan
  21. allanyed
    Hi Bill, I may be wrong but I don't think the foremast and fore topmast nor the main mast and main topmast and mizzen masts were ever connected this way on a ship, it does not look to be strong enough to hold them together with the weight of spars, sails, and force of the wind. I am pretty sure they would be set up in manner similar to the picture below. The below is from the cover of R. C. Anderson's book The Rigging of Ships in the Days of the Spritsail Topmast 1600-1720 but I would think for the 15th century they would have had something similar, utilizing trestle trees on which the tops rest and a mast cap for support rather than just a rope. I realize this is probably the kit design but hopefully some member will have more information for you and confirm the design one way or another. Allan
  22. allanyed
    I have found that the method Roger describes is pretty much full proof. I mark the spot with a fine tip marker pen then use a tiny burr which will get the hole started without wandering. Then all that is needed is to finish the hole with a drill bit. Allan
  23. allanyed
    As an update, there are now several folks that have offered help in converting 2D to 3D. 2D drawings of 9 and 12 pounder Blomefields in various lengths have been forwarded to them for conversion to 3D. Will continue to update as we move along. Hopefully the full set will wind up covering a long period of time and sizes and benefit scratch and kit builders alike in using appropriate cannon for at least English ships and cover 150 years or more. If anyone has 2D drawings (based on contemporary information,) of French, Dutch, Spanish or other nationalities, these can be added to the mix as well. Allan
  24. allanyed
    Hi Peter, Glad I was able to give a little help. I have been using the Veritas Mark II Standard Honing Guide for years with a Japanese wet stone that has two grits. I am guessing many folks have gone to ceramic stones in recent years, so there are a lot of choices. Regarding the Veritas set up, I assume there are other brands with similar designs, but this one has been great for me. IF the edge is in really bad shape with a chip or similar issue I would take it to a professional for the first grinding and sharpening then use the Veritas for maintaining the edge. I do strop with a piece of leather at times and can literally shave hair off my arm after it is honed. Of course a chisel with good quality steel is a key factor. Cheers Allan
  25. allanyed
    Sending you a PM Gray. Thanks! Allan

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...