Stuntflyer

Welcome back Erik!

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Absolutely, Erik. You should be👍

To finish up chapter 4 and the forward platforms,  the breasthooks were made.  There are two of them.   These are laser cut for you in two halves.  Its just easier to work with them this way.  I usually shape one half and lightly tack it in position.  Then I shape the other half and fit it in next to it.   At this point they can both be removed and joined together.  Do a quick sanding to refine everything and add the bolts.  The bolts are 30 lb. black line.  
 
The lower breast hook has etched bevel lines because the side that fits against the frames needs to be beveled.  Its just a start because everyone's model will be slightly different.
 

Lastly..to finish off this chapter I made the riding bitts.  Like the fire hearth, this wont be glued in position yet.  But its good to have at the ready.   We will need it before framing out the rest of the forecastle deck later.  So the cross beam is laser cut for you.  Just clean it up and shape to suit.  I just used some needle files, etc.   The uprights are basically made from 5/16" x 5/16" strips.   Measure against the plans and shape the tops to suit.  Use the plans as a guide.  Nothing earth shattering with these.  
 

 
 
I will paint the riding bitts red above the gun deck.  I used the plans to determine where that break would be.   Here is what it looks like after being painted and test fit.  Note the string...this is good to get in place now too.  Its glued lightly to the center of the stem and then taped to the top of the stern post.  It will help guide you when setting fittings along the center line.  It helps a lot!!!
 

The fire hearth and riding bitts have been set aside for safe keeping.
 
Next up chapter 5 which will take care of the aft lower platforms and a few other odds and ends.
 

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Just catching up, here - awesome work, as always.  The stove looks really great!  One question: after the flour/mortar application, is it even necessary to spray a final top-coat fixative, or will ambient humidity basically cement the flour in-place?

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Step by Step...
 

1. Laser cut cedar brickwork.   Lightly sand the char.  But not so much that you remove the etched mortar lines.   Just a little.  Especially on the edges of the pieces.   Many have bricks etched on both sides.
apply wipe on poly when finished...this is important to seal the wood a bit.
 

2. Yes its bright!!   But this is just the initial steps.  I used a red promarker, you can see which color to add the base coat of red to all faces of the brickwork.  Also note the two pieces that make up the sides have been glued together.  Make sure you have the holes and pieces facing the correct direction.
 

3.  Glue the sides to the back wall.  Keep nice right angles.   Also add the front piece.   This is left a bit long and you will have to trim it to fit.  DO NOT glue to the base.  This will be done much later in the project.   Much, much later.
 

4.  Using weathering powder add some red/brown colors and dark browns to suit.   It depends on how weathered you want to go with the fire hearth.  You will see this at the end.   Spray all the pieces lightly with some matte spray fixative when you are done.
 

5.  This is where the magic happens.   You could use white weathering powder but that would also pigment the bricks.  You dont really want that.   So instead use regular white flour.   Brush it on and push it into the mortar lines which are made pretty deep for you.   Dont go for a perfect even coverage here.  Experiment a little.  Push it in the cracks with your finger....pack it in there.  Then brush it off the brick faces with a light touch.  Experiment for the look you really want...use some additional weathering powders if you want to add soot and ash.   Make it a used hearth or a relatively new one!!!  Also note the frame on the base was painted black.  Dont spray with fixative.  The normal humidity in the air will fix the flour in position on its own.  It may take a day or so depending on the weather.  
 



6.  1/32" brass wire/rod (not included) were blackened and added as shown above.
 

 
7.  The hood...laser cut from 1/64" thick boxwood.   Glue the shorter back piece on the base first.  It should be a at a perfect right angle vertically and centered.

8.  Add the two sides.  You will need to bevel the bottom to sit flush on the base.
 

9.  Add the front piece...which is taller than the back piece.  Note how the front hangs over the the front of the base just a bit.  That is done on purpose.  It is correct.

10.  Finally add the top and front pieces.   apply filler to all the cracks and sand smooth for painting.   Also build the stack the same way and prepare for painting.
 

11. Hinges are laser board.   Construct them in the sequence shown above...left to right.   First add the bottom half of all the hinges.  Then the hinge pins are glued along the top edge.  Use 24 gauge black wire for that.  To finish that up,  set the top half of the hinges above the wire.  An eyebolt is also added in the center.  You can see that in the photos below of the finished fire hearth.  There are two of them shown...
 
A beat up used and weathered fire hearth....and a shiny almost new hearth.   Have fun with it and weather to your preferred tastes.  LOL
 



NOTE....the hearth is NOT glued to the base yet.  And the stack is NOT glued to the hood yet.  It is best to keep them separate for now. 
 
 
 

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike

Hull planking (prep)
One of the things I've been wanting to do was to see whether or not I could get away without having to spile the hull planks from 3/64" sheet. I was hoping that I could just edge bend boxwood planks to match a spiled shape. With that in mind I ran a test to see if indeed it could be done.
 
The sequence is a little off since I thought of taking the photos after some of the steps were completed. I retraced the steps as best I could. For better viewing I have focused in on a smaller area of the hull.
 
The first thing I did was to attach the hull template to my hull. I ran some 1/4" striping tape along the lower edge of the template and then back masked the upper edge of the tape. After that the original layer of tape was removed. You can see a bit of the back masking at the stem. I could have just drawn a line along the bottom of the template instead of using tape. Being a test of only one plank, I didn't want to do that. Hey, that's just me complicating things.

Here is the back masking (original taping removed) where the lower edge will line up with the upper edge of the plank.

 
I traced the lower edge of the tape (the shape for the upper edge of the plank). This gives me the shape needed for spiling or hopefully just some edge bending. You should be able to see the pencil marks across each frame.

The resulting shape resembles a gentle "S" curve. Something like this.

I was able to edge bend the boxwood to match the spiled shape without any difficulty. Clamping the test plank to the hull was done without having to do any twisting or bending. Mission accomplished!

Mike