Jump to content

Grand Banks dory by Cap'n'Bob - FINISHED - 1:32 - SMALL


Recommended Posts

As part of my last build, Joshua Slocum’s Spray, I built a dory and then cut it in half because he used half a dory as his “ship’s boat”.   I thought at the time a complete dory would be fun to build.

 

So, now, how were the old Grand Banks dories built? 

 

My research showed that during the 1880’s-1890’s the dory was built by the thousands, and was probably the first boat to be mass produced.  Each fishing schooner that went out carried as many dories and fishermen on board as it could.  This got me thinking.  The ship owners would be looking for the lowest price and the dory builders would be building as simply as possible to lower their cost.

 

The modern dory is a different boat.  The modern dory is long pieces of plywood and a few frames.  They have little rocker to almost flat on the bottom, and the chine strake is large at the ends and narrow in the middle.  This wastes wood and is something the dory builders of old would not have wanted to do. 

 

The written descriptions and pictures of the old dories show a boat with a deep rocker to the bottom and the chine plank is straight from bow to stern.  The old dory should be a simple boat to build. 

 

Now to this build.  Let’s have fun.  I will make the planks equal in width and straight from end to end and we will see what happens. 

 

post-513-0-87721200-1362862023.jpg

The half frame is a great advantage to mass production.  Several half frames can be made in advance and adjusted to fit at time of assembly. 

I made the half frames at 120 degrees. 

 

post-513-0-85043200-1362862084.jpg

post-513-0-43205800-1362862145.jpg

post-513-0-28619600-1362862146.jpg

Dories are made with lap strake construction.  The brass mounted on the angle prevents the angle from changing during sanding.  The brass is also mounted slightly above the angle to leave about .010” on the edge of the plank.

 

post-513-0-87437400-1362862146.jpg

post-513-0-41518000-1362862147.jpg

I did not know how much rocker there would be in the bottom so I could not mount the frames on a building board before mounting the chine strake.

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Bob,

The Grand Banks Dory was my first scratch build. In fact it is my first completed boat. I just completed it last week.

I used the plans from the Shearwater site but built it half size at 1:24 scale.

http://www.shearwater-boats.com/doryinst.html

I am going to try to attach a photo taken with my iPad - not the best quality but I'm pretty proud of this little guy.

Pete

post-274-0-94194700-1362895189_thumb.jpg

Link to comment
Share on other sites

Bob, great I will be following along.

 

Nice looking dory Pete.

 

Michael

Current builds  Bristol Pilot Cutter 1:8;      Skipjack 19 foot Launch 1:8;       Herreshoff Buzzards Bay 14 1:8

Other projects  Pilot Cutter 1:500 ;   Maria, 1:2  Now just a memory    

Future model Gill Smith Catboat Pauline 1:8

Finished projects  A Bassett Lowke steamship Albertic 1:100  

 

Anything you can imagine is possible, when you put your mind to it.

Link to comment
Share on other sites

Hi Pete,

              Your dory is well done. Glad to have another scratch builder aboard. 

 

Michael,

              Glad you found me.

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Interesting, Bob.  I'll be keeping an eye out to see how she goes together.

Augie

 

Current Build: US Frigate Confederacy - MS 1:64

 

Previous Builds :

 

US Brig Syren (MS) - 2013 (see Completed Ship Gallery)

Greek Tug Ulises (OcCre) - 2009 (see Completed Ship Gallery)

Victory Cross Section (Corel) - 1988

Essex (MS) 1/8"- 1976

Cutty Sark (Revell 1:96) - 1956

Link to comment
Share on other sites

Bob, this looks to be a fun build.  Mind if I follow along?

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

Augie,  Mark,

 

Thanks for stopping by.

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Elia,

 

I saw you lovely schooner the other day and was wondering how many dories she would have.

 

My dory for the Spray was 1:48.  Thay're a fun build.

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

]It’s amazing what you learn when you build a boat the way they were actually built.  I had always wondered why lap strake.  It seems like a difficult way to build a boat.  But then I decided to build a dory and guess what, they were lap strake built.  The building taught me why. 

 

The planks of a dory were only 5/8” thick, and the only way to get enough surface area between planks and provide a good seal is to put matching angles on planks so that instead of 5/8” surface you end up with about 1½”. 

 

 Here is the dory hull, still a long way to go. 

 

Bob

 

post-513-0-50995300-1363047811.jpg

 

post-513-0-23187800-1363047812.jpg

Edited by Cap'n'Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Yep, my coworker asked me why I wasn't overlapping my planks, and I asked why I would - he, having been a sailor most of his life until he moved to aerospace in his early 50's explained that it is authentic to the real ship's boats (in many cases) to have the planks overlap to create a seal. 

 

That looks pretty good there....nice and even.

-----------------------------------------------------------------------------------------------------

-Sarah

Current Build:

Krabbenkutter CUX-87

Harriet Lane

Fishcutter GO-38

 

In the Wings:

Corel Victory Cross section

 

Completed Build:

USS Missouri minimissouri.jpgHMS Bounty's Jolly Boat thumbnail.jpg Peterboro Canoe tiny.jpg

Link to comment
Share on other sites

Very nice Bob, I must have a go at the lapstrake method.

 

Michael

Current builds  Bristol Pilot Cutter 1:8;      Skipjack 19 foot Launch 1:8;       Herreshoff Buzzards Bay 14 1:8

Other projects  Pilot Cutter 1:500 ;   Maria, 1:2  Now just a memory    

Future model Gill Smith Catboat Pauline 1:8

Finished projects  A Bassett Lowke steamship Albertic 1:100  

 

Anything you can imagine is possible, when you put your mind to it.

Link to comment
Share on other sites

Thanks Michael,

 

Lapstrake is a lot easier then I thought it would be. 

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Bob:

This is a beautiful model. The paint work so far looks very clean. Very good job.

 

Russ

Link to comment
Share on other sites

Gerty,  Russ,

 

Thanks for stoppong by and your kind words.

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

hey there Bob.......glad to see you have another build in the works :)   I like the way you beveled those planks......If I had seen this earlier,  I could have done a better job with the AmericA  {I tried something similar}  I'll look forward in following your build......nice looking so far!...;)

I yam wot I yam!

finished builds:
Billings Nordkap 476 / Billings Cux 87 / Billings Mary Ann / Billings AmericA - reissue
Billings Regina - bashed into the Susan A / Andrea Gail 1:20 - semi scratch w/ Billing instructions
M&M Fun Ship - semi scratch build / Gundalow - scratch build / Jeanne D'Arc - Heller
Phylly C & Denny-Zen - the Lobsie twins - bashed & semi scratch dual build

Billing T78 Norden

 

in dry dock:
Billing's Gothenborg 1:100 / Billing's Boulogne Etaples 1:20
Billing's Half Moon 1:40 - some scratch required
Revell U.S.S. United States 1:96 - plastic/ wood modified / Academy Titanic 1:400
Trawler Syborn - semi scratch / Holiday Harbor dual build - semi scratch

Link to comment
Share on other sites

Thanks Michael,

 

Lapstrake is a lot easier then I thought it would be. 

 

Bob

Bob, lapstrake is not only easier but much more authentic. I love what you are doing.

 

It reminds me of the little sailboat I had in the SF Bay. It was a 'junior folkboat' (built in Denmark) and had mahogany lapstake planking on the hull. The 'problem' was that the outside was varnished and we had to haul her out twice a year to redo the hull and topsides. Lot's of sanding, but boy did it get some attention!!!

 

Are you familiar with the dories used by Powell when he went down the Colorado River? They look about the same????? 

Jay

 

Current build Cross Section USS Constitution  http://modelshipworld.com/index.php/topic/10120-cross-section-forward-area-of-the-uss-constitution/

Finished USS Constitution:  http://modelshipworld.com/index.php?/topic/103-uss-constitution-by-modeler12/

 

'A picture is worth a  . . . . .'      More is better . . . .

Link to comment
Share on other sites

Jay,

 

Thanks for looking in.  Sailing the SF bay must have been fun.

I know that some of todays Grand Canyon boats are dories but I thought Powell's boats were round bottom instead of the hard chine.

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Finally I was able to do a little more on the dory. 

I started to paint the inside the same blue as the outside, but everything I saw showed the inside tan, yellow or yellow-orange.  So I painter it a warm yellow.  

 

post-513-0-53775600-1364146015.jpg

 

I also added the lifting ropes in the bow and stern.

 

post-513-0-25643900-1364146016.jpg

post-513-0-89733800-1364146016.jpg

post-513-0-36767600-1364146017.jpg

 

Now I need to put the boat aside and make all the things that the fisherman needed I n the boat.

 

Later, Bob

 

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Looking great Bob.  That sure is YELLOW!!!!

Augie

 

Current Build: US Frigate Confederacy - MS 1:64

 

Previous Builds :

 

US Brig Syren (MS) - 2013 (see Completed Ship Gallery)

Greek Tug Ulises (OcCre) - 2009 (see Completed Ship Gallery)

Victory Cross Section (Corel) - 1988

Essex (MS) 1/8"- 1976

Cutty Sark (Revell 1:96) - 1956

Link to comment
Share on other sites

Augie,  Russ,

 

Thanks for looking in and your kind words.

 

I suspect it helped make them more visable.

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Now that, sir, is an excellent observation.

Augie

 

Current Build: US Frigate Confederacy - MS 1:64

 

Previous Builds :

 

US Brig Syren (MS) - 2013 (see Completed Ship Gallery)

Greek Tug Ulises (OcCre) - 2009 (see Completed Ship Gallery)

Victory Cross Section (Corel) - 1988

Essex (MS) 1/8"- 1976

Cutty Sark (Revell 1:96) - 1956

Link to comment
Share on other sites

Looks great Bob, I am suddenly hungry for a banana.

 

Michael

Current builds  Bristol Pilot Cutter 1:8;      Skipjack 19 foot Launch 1:8;       Herreshoff Buzzards Bay 14 1:8

Other projects  Pilot Cutter 1:500 ;   Maria, 1:2  Now just a memory    

Future model Gill Smith Catboat Pauline 1:8

Finished projects  A Bassett Lowke steamship Albertic 1:100  

 

Anything you can imagine is possible, when you put your mind to it.

Link to comment
Share on other sites

Michael,

 

Through some icecream and syrup on that banana and I'll join you.  :)

 

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Bob,

 

Love your build, and it's colours. Though you can keep the icecream ... currently between 0 and -7 Celcius here, and I detest the cold.

Carl

"Desperate affairs require desperate measures." Lord Nelson
Search and you might find a log ...

 

Link to comment
Share on other sites

Carl,

 

I agree whole heartedly with you about the cold.  That's why I live in Arizona.

 

Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Today I made a couple of buckets for the dory.  There are many methods, but this is the way I did it.

 

 

First I cut 12 staves the same size and mount them on a piece of masking tape.  These are .03” X .50” X .16”.  

post-513-0-16680500-1364242602.jpg

I sand a slight taper from end to end so one end is narrower than the other.

post-513-0-79943000-1364242602.jpg

Then one by one I sand the edges so the cross section is a trapezoid.

post-513-0-69482600-1364242603.jpg

Place them side by side on clear tape with the smaller face pointing up and the narrow ends all at the same edge.  You can see how the taper causes a curve.

post-513-0-34948000-1364242604.jpg

Cut off one end of the tape flush with the edge of the last stave.

post-513-0-01983800-1364242605.jpg

Now roll the tape with the wood inside until the first and last pieces of wood meet and the tape on the end goes around the outside to hold it all together.

post-513-0-84702300-1364242605.jpg

Make a disc of wood to fit inside the smaller end and glue it into place.

post-513-0-43643900-1364242606.jpg

The bands are made from narrow strips of card stock.  After cutting I stained them.

post-513-0-21425700-1364242607.jpg

Cut the tape off the lower part of the bucket and glue the card stock to look like a band.

post-513-0-97469400-1364242607.jpg

Remove the rest of the tape and glue the other band around the top.

post-513-0-73401600-1364242608.jpg

I didn't measure the taped staves for the diameter of the bottom but you could measure everything carefully and use geometry.

 

 

Bob

Edited by Cap'n'Bob

Every build is a learning experience.

 

Current build:  SS_ Mariefred

 

Completed builds:  US Coast Guard Pequot   Friendship-sloop,  Schooner Lettie-G.-Howard,   Spray,   Grand-Banks-dory

                                                a gaff rigged yawl,  HOGA (YT-146),  Int'l Dragon Class II,   Two Edwardian Launches 

 

In the Gallery:   Catboat,   International-Dragon-Class,   Spray

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...