Gregory
-
Posts
3,047 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by Gregory
-
Looks way too small to me.😁 -
This might be a good start: Model Shipways 18th Century Longboat Wooden Model Ship Kit & Tools
-
The copper leaf itself is very fragile, not much thicker than a layer of paint, but the patina showed no signs of coming off when I buffed it. With something like copper tape, you might have some wiggle room to burnish some of it off, if it is too dark for your taste. It actually ended up a little darker than I planned. I did leave it overnight, but I wish I had of monitored it and checked every hour or so. This was a very small piece, and I did it inside of a zippered sandwich bag with one egg. I was thinking with something like the hull of a ship, I would make a framework to drape plastic over and put my eggs under
-
This is the cupola from my Resolution. It started out as copper leaf then treated with the boiled egg method.
-
You want quick? Overnight in an enclosure such as a plastic bag with some chopped boiled eggs.
-
I look in re-sale shops for dress shirts and dresses with a high thread count. Preferably cotton .
-
Which one? Rattlesnake, Fair American, Prince de Neufchatel , Armed Virginia Sloop ?
-
I believe the MS cradles are a bit small, but I think the Syren 1:48's might look a bit big. I will PM you later about a solution I have in mind..
-
Hey guys, the question was: " ....which have the most detailed build instruction? Can we try to answer that question, instead of launching off into our thoughts on the other pitfalls that a beginner might encounter?
-
Vanguard Models Next would be any ModelShipways kit designed by Chuck Passaro as well as any kit from Syren Ship Model Co.
-
Forming a rabbet
Gregory replied to DaveBaxt's topic in Building, Framing, Planking and plating a ships hull and deck
If you go the route of replacing the stem and keel, my FET method will work. You can see in my Resolution build where I replaced the stem and keel, but I didn't have the FET, I used an added strip to form the rabbet -
Forming a rabbet
Gregory replied to DaveBaxt's topic in Building, Framing, Planking and plating a ships hull and deck
Dave , after looking at your build log I have to ask, is the stem and keel part of the backbone? If so, my method of using the FET for the rabbet in the stem area probably would not work after all. -
Forming a rabbet
Gregory replied to DaveBaxt's topic in Building, Framing, Planking and plating a ships hull and deck
Dave , I actually used the Proxxon FET to form a rabbet on the MS 1:48 longboat, including the stem/bow. I'll have to get back to you later with some pics. -
Cordless Micro Drills
Gregory replied to CLovehitch's topic in Modeling tools and Workshop Equipment
Along with what Bob is saying, I don't see that being much more useful than a pin vise. It is going to stall very easily and the tool selection is very limited compared to devices with a 1/8 collet sharing the Dremel type tools. While not cordless, I have found this to be very useful for light work. It weighs in at 6.8 oz, so is very easy to use. Dremel 2050-15 Stylo It also takes the Dremel keyless chuck eliminating the need to change collets for the smallest drill bits on up to 1/8 for all Dremel type accessories.
-
Allan, do you disagree that block size is determined by rope size? The type of ship shouldn't matter.. Here is a basic table from Mondfeld
-
The size of the blocks are based on the rope size being used, not the other way around. You find the rope size you are using then find the block for that size rope.
-
This might help from a recent discussion:
-
Jiggling or Nibbling
Gregory replied to CLovehitch's topic in Building, Framing, Planking and plating a ships hull and deck
I have found these mini heat guns to work well. Mlife Mini Heat Gun
-
Jiggling or Nibbling
Gregory replied to CLovehitch's topic in Building, Framing, Planking and plating a ships hull and deck
The Jiggling or Nibbling didnt show up till late 18th century.. The hook method that Allan illustrated may have been used. -
Split ring making process
Gregory replied to Dave_E's topic in Metal Work, Soldering and Metal Fittings
While I'm sure soldering produces a great result it introduces a another set of tools, materials and skill set, and the result requires blackening. It might fit better in another topic, as the one who requested help said: -
Split ring making process
Gregory replied to Dave_E's topic in Metal Work, Soldering and Metal Fittings
Thanks for starting this. I have struggled with making these look good. I really like CPDDET's fine cut-off disks.. I now have some on order. Like everything he does, Chuck makes it look so easy. He's probably made thousands of these. If only he would start selling them..
-
Split ring making process
Gregory replied to Dave_E's topic in Metal Work, Soldering and Metal Fittings
Coating with CA might work as well. -
The best place could be anywhere depending on where you are located.. As for the 2nd question, a good scroll saw has been the best option for many years, decades, now. Next up would be a laser cutter, but it has a lot of accompanying skill requirements with the software it requires..
-
From the link: "The Ropewalk Machine itself is no longer available"
-
This is another excerpt from the Magoun book. While nothing specific, the impression I get from the book is that it w as an English built ship. I have no knowledge of the expertise of R.C. Anderson.
Our Emblem ®
