Beef Wellington

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.

 

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.

 

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.

 

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.

 

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.

 

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.

 

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.

 

Thanks Andrew, Allan and Dave for your thoughts and comments regarding Diana's boats.
Dave, the Vanguard boats come with both P/E brass and wood oars in 0.6mm pearwood. For the 32' pinnace they are 67mm long. The brass oars are 64mm. I'm not sure why they are different and the wooden oars different again from seemingly the same item offered separately on the Vanguard website.
Hope this helps. 
David 

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.

 

I think Jaager is correct: turned rather than tuned. Sometimes transcribing period script is difficult.

It also may be a typo -  maybe turned up was intended?  Indicating that the plates were to be attached to the keel?

I was also impressed with their service.  If you are concerned, I would suggest ordering just one to see if you like the product before committing to the full complement.

Philip Reed's Speedwell
 
 

Many thanks Keith,
it is already displayed in my little private museum together with 8 other models...
The Gorch Fock model had (in lack of place) to be moved upstairs to my attic office
 
Nils

 

 

 
 

The casing
 
the casing is now finished the model set inside and this closes the build log
 
Nils

 
 

 

Thank you, James, those figures you directed me to turned out better than I had feared.👍
 
@ Chris, good luck with that, what you can’t see are the other models resident in my office – Norske Love, a French Seventy-four, and a Flower Class Corvette.
Apart from the Shower room and Kitchen virtually all rooms have their ship model(s). I do have an understanding wife but she draws the line at the bedroom, but I got away with a couple of ship paintings. 🤞
 
@ shipman – he is but a lowly Rear Admiral of the least senior squadron (Blue) and besides he ain’t going anywhere.😉
 
@ Jason – Thank you Jason – it looks fine providing a macro lens is not allowed anywhere near it.🙄
 
B.E

Just amazing work at 1:64.  Well done B.E.   I'm looking forward to see what's next.

I was also impressed with their service.  If you are concerned, I would suggest ordering just one to see if you like the product before committing to the full complement.

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.

 

I was also impressed with their service.  If you are concerned, I would suggest ordering just one to see if you like the product before committing to the full complement.

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.

 

I’ve had both period and modern fittings direct from Model Monkey and have found both the quality and service to be excellent.
 
Gary

Congratulations Mike, you should be very proud of the excellent result!

Thats a very nice treatise on rigging Mike!  I think your efforts to show this for future Snake builders will be very valuable.  Shes looking fantastic, very well done.

Final shaping of the hull, installation of tafferal and plansheer:
Happy New Year everyone!  Lots of work over the holidays has finally resulted in what I consider to be a major milestone, namely the final shaping of the hull, installation of tafferal and plansheer.  Before I could proceed, had to finally deal with some cannon dislocations that I had been putting off for a while - two of the rear cannons has become loose, the carriages were still firmly fixed luckily, but the barrels had broken away.  Thank goodness for those long thin CA tubes that allowed these to be re-glued through the gunport...panic over.
 
Once the volutes had been installed and the gunports were cut out and finished (photos below show the aft and fore positioning), it was possible to install the remainder of the quarterdeck drift which was installed parallel to the main wale.  This then allowed the final shape of the upper hull to be determined, once again parallel to the main wale.  The topside of the bulwarks should be horizontal, and I found that the easiest way to do this was to use a long enough file that would reach from one side to the other, fine tuning one side at a time. 

The upper edge of the tafferal was also tweaked to ensure it was parallel the keel (even on the original NMM drawings, it was not possible to determine whether this should be parallel to the sheer of the quarterdeck or keel.  After making a template, the tafferal was cut out of a pear sheet, and pre-bent on a template previously made when originally making the stern fascia - this needs to be made from 3 pieces.  This seemed the most reliable way to get this done given the compound curves, and the pear wood was soaked and steamed on the former before being left to dry for 24hrs to ensure it was fully dried.  Once the main section had been installed, the two small sections over the quarter galleries needed to be made.  To do this, a separate former was made up to introduce the different curvature - these pieces are small, and proved to be quite challenging to shape (The second photo illustrates this step, but shows a 'reject').  Painting the edge highlight also proved 'challenging' to say the least.
 

It was also realized that the rear edge of the hull planking needed to be extended further aft - this is needed to account for the counter timbers which of course are not present in the POB kit.  I debated doing this, but felt it would be necessary to ensure the tafferal fife rail can terminate properly and not be left hanging in space.  The tops of the counter timbers will not be added until the tafferal fife rail is installed down the road as I suspect this will be a magnet for damage.

Not much more to be said, here are some overall shots of the finalized stern and quarter gallery area.  I am satisfied with the way this turned out, but as anyone who has built this kit can testify, getting the positioning and sizing of all these elements 'right; is a challenge.  Overall, it has been an exercise in constant compromize and adjustment between the original plan dimensions, the AOTS diagrams (which are not all consistent or fully representative of 3D reality) and the kit dimensions.  I will likely need to reduce the dimensions shown on the plans of the decorative upper finishing fretwork that will be installed on top of the quarter gallery roof by 1mm or so to avoid it protruding above the stern fascia - another decision for down the road.

Gunports were tested with anticipated armament, in this case Vanguard 9lb carriages and Syren barrels.  Had I been only using these, I'm sure I would have used the Vanguard barrels as well, but I wanted to keep the use of brass barrels for consistency...

...and finally some overall shots of where things stand, the lights are only temporarily installed for now.