giampieroricci Posted December 15, 2013 Author #61 Posted December 15, 2013 I finally finished the job of balancing the interior of the coasts: a big job!I then set the keelson: aykutansin, mtaylor, egen and 3 others 6 Quote
giampieroricci Posted December 21, 2013 Author #62 Posted December 21, 2013 (edited) I finished the keelson, and then I started laying dormant bridge Edited September 14, 2014 by giampieroricci Wishmaster, mtaylor, druxey and 10 others 13 Quote
giampieroricci Posted December 26, 2013 Author #63 Posted December 26, 2013 (edited) I also fixed the sleepers of the formwork, but first I had to make the last beam, with a particular shape as it follows the curve of the transom and gets stuck there. I also started to open a gunboat Edited September 14, 2014 by giampieroricci Jay 1, druxey, herask and 12 others 15 Quote
druxey Posted December 27, 2013 #64 Posted December 27, 2013 Lovely work, Gianpiero! Quote Be sure to sign up for an epic Nelson/Trafalgar project if you would like to see it made into a TV series http://trafalgar.tv
giampieroricci Posted December 29, 2013 Author #65 Posted December 29, 2013 (edited) Thank you!!! I finally fixed the last beam formwork, which fits into the oarlocks of the transom: Meanwhile, I continued working on the opening of the gunboats of the bridge and the openings for the scuttles of the oars; for them I made a template sheet to try to make them all equal Edited September 14, 2014 by giampieroricci druxey, popash42, fatih79 and 5 others 8 Quote
giampieroricci Posted December 29, 2013 Author #66 Posted December 29, 2013 (edited) more.... Edited September 14, 2014 by giampieroricci Bluto 1790, mtaylor, druxey and 10 others 13 Quote
giampieroricci Posted December 31, 2013 Author #67 Posted December 31, 2013 (edited) I finished opening the gunboats and I started to prepare the thresholds, which have a particular concavity, to which I have built a custom "tool" this is the tool: Edited September 14, 2014 by giampieroricci NMBROOK, avsjerome2003, Anja and 9 others 11 1 Quote
giampieroricci Posted January 1, 2014 Author #68 Posted January 1, 2014 Today I finished working on the gunner. I have completed the thresholds and lintels. This is the window of the cabin of the Captain DmitriyMarkov, SailorGreg, avsjerome2003 and 9 others 11 1 Quote
giampieroricci Posted January 4, 2014 Author #70 Posted January 4, 2014 I finished the gunboats also from the inside I also fixed the sleepers of the castle I also started to prepare the battens of flowers: job rather difficult to prepare, especially because you do not have much space to be able to score perfectly all measures avsjerome2003, Elmer Cornish, druxey and 6 others 9 Quote
giampieroricci Posted January 5, 2014 Author #71 Posted January 5, 2014 Before continuing the work inside, I decided to finish the topsides on the outside because I want to remove all the bolts that cause me many problems and hassles by cutting the excess coast and finishing on the gunwale.I then prepared the tool, converted from an old saw blade and molded with a small disk, for the course that I started to fix O.Klausen, aykutansin, cabrapente and 9 others 12 Quote
giampieroricci Posted January 6, 2014 Author #72 Posted January 6, 2014 Now it begins to outline the final form of this corvette, at least on the starboard side: I fixed the piece of plank molded bow, prepared and glued the other strip molded, smaller, which limits the performance of the formwork and I started to cut and trim oarlocks of double coasts popash42, avsjerome2003, Bluto 1790 and 7 others 10 Quote
giampieroricci Posted January 6, 2014 Author #73 Posted January 6, 2014 more photos WackoWolf, tarbrush, CaptMorgan and 13 others 16 Quote
archjofo Posted January 7, 2014 #74 Posted January 7, 2014 Hello, it is wonderful to follow your progress. An excellent performance. Quote Best regards Johann Video: La Créole - Scale 1/48, French corvette of 1827 - naval artillery La Créole - Scale 1/48, French corvette - Construction of long boat La Créole - Scale 1/48, French corvette - Construction of the masts La Créole - Scale 1/48, French corvette - 2019 La Créole - Scale 1/48, French corvette - standing rigging - part 1 La Créole - Scale 1/48, French corvette - standing rigging - part 2 La Créole - Scale 1/48, French corvette - standing rigging - part 3 See also our german forum for Sailing Ship Modeling and History: www.segelschiffsmodellbau.com
giampieroricci Posted January 11, 2014 Author #75 Posted January 11, 2014 Thank you!! :) Small forward: I set the molded course on the left side and I started to wrap the starboard side starting with the two courses between the moldings at the stern, ebonyThis is my "powerful" cutting tool for the oarlocks of double coasts: Dubz, mtaylor, WackoWolf and 8 others 11 Quote
giampieroricci Posted January 12, 2014 Author #76 Posted January 12, 2014 (edited) some photos Edited September 14, 2014 by giampieroricci Jeronimo, WackoWolf, fatih79 and 6 others 9 Quote
giampieroricci Posted January 21, 2014 Author #77 Posted January 21, 2014 (edited) I continued with the bandage of the topsides, I realized I had made a serious error to paste the thresholds of the gunboats: the angle between the threshold and the side wall is pretty sharp and this did not allow for a perfect installation of the course below thresholds, for obvious reasons, leaving a little 'air.I removed very carefully thresholds and set the course and the joints redone, everything went perfectly, although I remove a threshold, have resulted in the rupture of an oarlock to the coast, but this will not be seen because it will be covered by the plating . Edited September 14, 2014 by giampieroricci robbl, mtaylor, Jeronimo and 8 others 11 Quote
giampieroricci Posted January 21, 2014 Author #78 Posted January 21, 2014 (edited) more photos Edited September 14, 2014 by giampieroricci NMBROOK, Bluto 1790, mtaylor and 9 others 12 Quote
giampieroricci Posted January 25, 2014 Author #79 Posted January 25, 2014 (edited) I finished the installation of the courses between the doors and started to finish with fine sandpaper to remove the glue residue and the excess of black cardboard. I also finished the edges of the gunboats and scuttles the oars. Edited September 14, 2014 by giampieroricci mtaylor, ChrisLBren, fatih79 and 7 others 10 Quote
giampieroricci Posted January 26, 2014 Author #81 Posted January 26, 2014 (edited) Little progress: Edited September 14, 2014 by giampieroricci iosto, fatih79, SailorGreg and 12 others 15 Quote
giampieroricci Posted February 9, 2014 Author #82 Posted February 9, 2014 Meanwhile, I am continuing the bandage left side and riveting to starboard. Jeronimo, dvm27, Wishmaster and 9 others 12 Quote
giampieroricci Posted February 22, 2014 Author #83 Posted February 22, 2014 small forward: I finished reinforcements in ebony at the bow on the left side and nailing on the starboard side Mirabell61, NMBROOK, cabrapente and 11 others 14 Quote
Mirabell61 Posted February 22, 2014 #84 Posted February 22, 2014 What a beautiful hull Giampieroricci ! lovely lines of that ship, and Iike the tones of the Wood used, it gives it all an authorised historic touch Well done ! Nils Quote Current builds -Lightship Elbe 1 Completed - Steamship Ergenstrasse ex Laker Corsicana 1918- scale 1:87 scratchbuild - "Zeesboot" heritage wooden fishing small craft around 1870, POB clinker scratch build scale 1:24 - Pilot Schooner # 5 ELBE ex Wanderbird, scale 1:50 scratchbuild - Mississippi Sterwheelsteamer built as christmapresent for grandson modified kit build - Chebec "Eagle of Algier" 1753--scale 1:48-POB-(scratchbuild) "SS Kaiser Wilhelm der Grosse" four stacker passenger liner of 1897, blue ribbond awarded, 1:144 (scratchbuild) "HMS Pegasus" , 16 gun sloop, Swan-Class 1776-1777 scale 1:64 from Amati plan -"Pamir" 4-mast barque, P-liner, 1:96 (scratchbuild) -"Gorch Fock 2" German Navy cadet training 3-mast barque, 1:95 (scratchbuild) "Heinrich Kayser" heritage Merchant Steamship, 1:96 (scratchbuild) original was my grandfathers ship -"Bohuslän" , heritage ,live Swedish museum passenger steamer (Billings kit), 1:50 "Lorbas", river tug, steam driven for RC, fictive design (scratchbuild), scale appr. 1:32 under restoration / restoration finished "Hjejlen" steam paddlewheeler, 1861, Billings Boats rare old kit, scale 1:50
giampieroricci Posted February 22, 2014 Author #85 Posted February 22, 2014 Thank you very much Nils!! Quote
giampieroricci Posted March 8, 2014 Author #86 Posted March 8, 2014 I finally finished the nailing of the courses of the topside and I have built a temporary basis to hold the model out of the yard popash42, fatih79, Erebus and Terror and 10 others 12 1 Quote
DorinC Posted March 15, 2014 #87 Posted March 15, 2014 Amazing work Giampiero , molto bello !!! Quote
beaver Posted March 15, 2014 #88 Posted March 15, 2014 magnificent work Giampiero. very beautiful model! Vadym Quote
giampieroricci Posted March 23, 2014 Author #89 Posted March 23, 2014 thank you very much, friends!!! I started to prepare the two courses of the battens "of the flowers" of the left side. A work quite long, since I've done all the joints by hand with a sharp knife. SailorGreg, WackoWolf, PeteB and 8 others 11 Quote
giampieroricci Posted April 6, 2014 Author #90 Posted April 6, 2014 I started covering the bottom of the hold NMBROOK, aykutansin, Dubz and 15 others 17 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.