Jump to content

San Francisco by vulcanbomber - FINISHED - Artesania Latina - (Original Version)


Recommended Posts

This was my very first build. It is the original version of the San Francisco, not to be confused with the San Francisco II, there are slight differences, the main one being the hull which is double planked with basswood and Sapeli veneer, whereas the San Fran II is single planked with mahogany.

 

I didn't like the gun carriages that came with the kit and with help from other members made my own which were more in keeping with the era of the ship.

 

I also made changes to the rigging, the kit instructions, for me, were too simplified so I did a lot of research and added more accurate rigging.

 

I learnt a lot from this build and she now sits in pride of place in my lounge.

 

The box:

post-3-0-78839900-1360962061_thumb.jpg

 

The Box:

post-3-0-22749800-1360962073_thumb.jpg

 

Inside the box:

post-3-0-11622000-1360962087_thumb.jpg

 

First the bulkheads were dry fitted, checking for fit and adjusting if neccessary before gluing in place. It is important to make sure the keel is straight and the bulkheads are at a 90deg angle to the keel to prevent problems with planking later.

post-3-0-53013900-1360962097_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

The next stage was to plank the decks, there were three the lower one, the beak, the forcastle, the main and the poop deck.

 

I wanted to simulate calking and the easiest method I seemed to find was by running a pencil down one edge of each plank. I cut the planks to a scale length and staggered them (I now know the pattern is incorrect, but it was a learning curve. ;) )

 

The trenails I made by using a sharp pointed object (actually a pickle fork!) then turned the point of a pencil in the hole to darken it slightly.

 

The results you can see below:

post-3-0-11724300-1360962843_thumb.jpg

 

I added the decks to the keel and bulkhead assembly:

post-3-0-58338600-1360962886_thumb.jpg

 

The bulkhead at the bow and under the poop deck were planked with sapeli:

post-3-0-46289400-1360962938_thumb.jpg

 

A close up of the main deck:

post-3-0-97543300-1360963037_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Next the quarter deck and poop deck were planked and added and the poop bulkhead planked:

post-3-0-12883600-1360963173_thumb.jpg

 

The beak had the decorative strips added:

post-3-0-21662800-1360963272_thumb.jpg

 

post-3-0-95614800-1360963295_thumb.jpg

 

post-3-0-12777700-1360963312_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Next the keel and bulkheads were sanded in preparation for attaching the bulwarks and hull planking:

post-3-0-57934800-1360963464_thumb.jpg

 

post-3-0-21226400-1360963480_thumb.jpg

 

The bulwarks were planked on the inside:

post-3-0-33475700-1361014131_thumb.jpg

 

Next I attached the bulwark (rubber bands are your friends!) The beak and gunport snapped (See red circles):

post-3-0-98753000-1360963490_thumb.jpg

 

The crack near the gunport:

post-3-0-08916200-1360963508_thumb.jpg

 

It was at this stage and with the damaged bulwark that I lost my confidence and began to dispair, No matter how I tried I couldn't seem to get it right, at this point I received so much help, support and encouragement from MSW members that they picked me up and helped me through it all. If it hadn't been for this great site, the model would have ended up in the bin!

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

With encouragement from my new found friends and some confidence returning I attached the port side bulwark:

post-3-0-05148000-1360964000_thumb.jpg

 

This is one of the differences between my San Fran and the San Fran II. The beak. The bulwarks don't end at the side of the forcastle as they do on the San Fran II, but continue all the way forward creating the beak:

post-3-0-53921100-1360964045_thumb.jpg

 

post-3-0-89216900-1360964057_thumb.jpg

 

The rear of the ship and the bulwarks:

post-3-0-35156400-1360964061_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Caroline,

So happy to see you had this log backed up and saved. Although I am currently building a II, I have been refering often to your log for inspiration and guidance.

 

Robbyn

If you risk nothing, you risk everything!

 

Current builds

Syren (Model Shipways) version 2.0

AL San Francisco II

Mordaunt (Euro Model)

Completed Builds

18th Century Longboat designed by Chuck Passaro
 

In the closet

Battle Station

Al Charles Morgan (1980s version)

 

Link to comment
Share on other sites

Hi Caroline, 

Great to see you and your San Francisco back. 

Mark
"The shipwright is slow, but the wood is patient." - me

Current Build:                                                                                             
Past Builds:
 La Belle Poule 1765 - French Frigate from ANCRE plans - ON HOLD           Triton Cross-Section   

 NRG Hallf Hull Planking Kit                                                                            HMS Sphinx 1775 - Vanguard Models - 1:64               

 

Non-Ship Model:                                                                                         On hold, maybe forever:           

CH-53 Sikorsky - 1:48 - Revell - Completed                                                   Licorne - 1755 from Hahn Plans (Scratch) Version 2.0 (Abandoned)         

         

                                                                                                                                                                                                                                                                                                

Link to comment
Share on other sites

Glad you're reposting this!! I built this kit last year and your log was a great help - I'm only sorry I never said anything about it before - but thank you!! A beautiful build looking good atop the fish tank if I remember correctly!

hamilton

current builds: Corel HMS Bellona (1780); Admiralty models Echo cross-section (semi-scratch)
 
previous builds: MS Phantom (scuttled, 2017); MS Sultana (1767); Corel Brittany Sloop (scuttled, 2022); MS Kate Cory; MS Armed Virginia Sloop (in need of a refit); Corel Flattie; Mamoli Gretel; Amati Bluenose (1921) (scuttled, 2023); AL San Francisco (destroyed by land krakens [i.e., cats]); Corel Toulonnaise (1823); 
MS Glad Tidings (1937) (in need of a refit)HMS Blandford (1719) from Corel HMS GreyhoundFair Rosamund (1832) from OcCre Dos Amigos (missing in action); Amati Hannah (ship in a bottle); Mamoli America (1851)Bluenose fishing schooner (1921) (scratch); Off-Centre Sailing Skiff (scratch)
 
under the bench: MS Emma C Barry; MS USS Constitution; MS Flying Fish; Corel Berlin; a wood supplier Colonial Schooner Hannah; Victory Models H.M.S. Fly; CAF Models HMS Granado; MS USS Confederacy

Link to comment
Share on other sites

Thanks guys, Yes, I'm going to repost my San Fran again in full.

 

Mark, yup, we're back! It's certainly bringing back memories re-posting this log. Will also start on my Pegasus soon too.

 

Robbyn, I'm glad my log helped you with your build. How far are you along and I'll try and catch up as quick as I can for you. ;)

 

Hamilton, It's good to know that it was a help to you and yes you remebre correctly, she is on top of the fish tank. :)

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

I decided to put another layer of planking inside the bulwarls, mainly to disguise the damage by the gunport and also to strengthen it:

post-3-0-59253200-1361027162_thumb.jpg

 

Next I planked the transom and attached it to the stern:

post-3-0-46177700-1361027181_thumb.jpg

 

post-3-0-97900200-1361027184_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

I was getting nearer and nearer to having to start the first planking, it was making me nervous, so to put it off for as long as I could i decided to make my own ship's boat as I hated the ugly metal one included in the kit:

post-3-0-16168600-1361027391_thumb.jpg

 

First I made it from off cuts of the deck planking strips. I made rough keel and a set of bulkheads, cuting them as narrow as I could and then planked the outside. before trying to reduce the 'ribs' the bulkheads made:

post-3-0-20559000-1361027393_thumb.jpg

 

post-3-0-79704300-1361027394_thumb.jpg

 

I wasn't happy with it and so I scrapped it, reused the keel and made new bulkheads and planked it all again, I was happier with this one and proceeded to kit it out and stain it:

post-3-0-44757400-1361027409_thumb.jpg

 

post-3-0-29587000-1361027420_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Encouraged by a very good friend who donated some cheery I made a better version, I again made a keel by gluing strips of the cherry together and made some rough bulkhead (Not shown) then I planked it. Once the planking was complete, I carefully removed the bulkheads and cut some thin strips of cherry and glued them in to simulate the 'ribs':

post-3-0-78004900-1361028294_thumb.jpg post-3-0-60032300-1361028296_thumb.jpg

post-3-0-23420300-1361028272_thumb.jpg

 

Once they were glued in I added a strip around the inside and a capping on top, just to neaten the top edge:

post-3-0-34222000-1361028298_thumb.jpg post-3-0-81676200-1361028300_thumb.jpg

 

Next I added the seats at the stern and bow and the flooring then stained the inside with cherry stain:

post-3-0-63811800-1361028303_thumb.jpg post-3-0-36839100-1361028310_thumb.jpg

 

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Finally the rest of the seats were added:

 

 

Next to version number two:

post-3-0-90357500-1361029091_thumb.jpg

 

post-3-0-56787400-1361029115_thumb.jpg

 

post-3-0-66069400-1361029117_thumb.jpg

 

Stained and varnished.... Finished!

post-3-0-62253800-1361028965_thumb.jpg

 

post-3-0-26950200-1361028969_thumb.jpg

 

post-3-0-39951700-1361028972_thumb.jpg

 

post-3-0-87692400-1361028975_thumb.jpg

 

post-3-0-84861500-1361028978_thumb.jpg

 

Now I couldn't put it off any longer, it was time to start the planking, this is where the planking tutorial helped me.

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Caroline,

Just finished the first layer of planking, I have been asking for adivice in another post as to whether my pattern is good enough to repeat for the second layer. Hoping that following the first (while avoiding the earlier troubles) will make that second layer go easier and smoothly :D  So looking forward to your reposts of your planking pics.

Robbyn

If you risk nothing, you risk everything!

 

Current builds

Syren (Model Shipways) version 2.0

AL San Francisco II

Mordaunt (Euro Model)

Completed Builds

18th Century Longboat designed by Chuck Passaro
 

In the closet

Battle Station

Al Charles Morgan (1980s version)

 

Link to comment
Share on other sites

Hi Robbyn, I'll try and do the planking stage for you.

 

Hi John, Yes, I'm getting there, slowly but surely!

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Now came time for planking.

 

After reading the tutorial I followed the advice of several members and used balsa to fill in the bow and stern to give more surface area to attach the planking to:

post-3-0-92405900-1361131305_thumb.jpg

 

Next I attached the garboard planks (The first plank next to the keel) and the first planking strip below the bulwarks. Then I measured the halfway point on the bulkhead between these two planks:

post-3-0-89191200-1361131307_thumb.jpg

 

Then I attached a plank along this line:

post-3-0-92859300-1361131309_thumb.jpg

post-3-0-95152300-1361131311_thumb.jpg

post-3-0-93004900-1361131313_thumb.jpg

post-3-0-91676000-1361131315_thumb.jpg

 

It was after posting these pics that a member pointed out that the ends finished too far up and would make the bow too crowded. I corrected this as you can see in the next pic:

post-3-0-28962500-1361131339_thumb.jpg

 

Next i measured the largest distance between the middle and the bulwark planks and divided it by the width of the planking material, this gave me the number of planks needed to fill that area. The next stage was to measure the other bulkheads and divide the result by the number of planks used, that then gave the width the plank needed to be trimmed to. Bearing in mind you shouldn't trim them to less than half their width.

 

You can see how much the planks need to be tapered at the bow:


post-3-0-62847800-1361131340_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

The stern needed less trimming:

post-3-0-28471900-1361132607_thumb.jpg

 

I continued planking the gap and when it was closed started the gap between the midway point and the keel:

post-3-0-50935700-1361132634_thumb.jpg

 

post-3-0-64646200-1361132636_thumb.jpg

 

post-3-0-21714300-1361132638_thumb.jpg

 

post-3-0-64473200-1361132645_thumb.jpg

 

post-3-0-23358000-1361132647_thumb.jpg

 

Once the planking was finished, I gave it a really good sanding. It is important to get the surface as smooth as possible to have a good base for the second planking, otherewise every dip and bump will be noticible when the second planking is finished:


post-3-0-01561200-1361132906_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

After ensuring a smooth surface I gave the hull a liberal coat of diluted PVA glue to ensure the planks were firmly attached in preparation for the gunports, I had to plan where to place the gunports, I used a piece of tracing paper and traced the upper part of the ship and the location of the ports and transferred this to the ship, then cut the ports out:

post-3-0-30538300-1361133256_thumb.jpg

post-3-0-85688200-1361133258_thumb.jpg
 

Next I attached the keel:

post-3-0-35414900-1361133260_thumb.jpg

 

Thank planked the transom:

post-3-0-90826600-1361133261_thumb.jpg

 

And added the rudder post:

post-3-0-36478000-1361133263_thumb.jpg


Now it was time for the second planking. I followed the same rules at the first planking by measuring and marking the sections, then placed the first strip of second planking tight up under the beak and let the plank run naturally along the hull to the stern:


post-3-0-06878300-1361133265_thumb.jpg

 

post-3-0-44386600-1361133774_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

I quickly found that the markings I placed on the hull didn't help me at all and it was a case of 'make it up as I go along'!

 

The first nine planks I didn't taper or tapered very little:

post-3-0-66468700-1361133990_thumb.jpg

 

It was here that I realised the planking wouldn't go as planned, the thin veneer really had to lie naturally along the hull, it couldn't as easily be shaped without it breaking. So I placed the next strips and let them lay naturally and trimmed them to fit:

post-3-0-66129300-1361134020_thumb.jpg

 

post-3-0-67045500-1361134022_thumb.jpg

 

post-3-0-56573400-1361134039_thumb.jpg

 

post-3-0-60343900-1361134041_thumb.jpg

 

post-3-0-62651500-1361134043_thumb.jpg

 

I continued planking, allowing the strips to follow the hull naturally:

post-3-0-29545200-1361134438_thumb.jpg

 

post-3-0-48416900-1361134439_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Now was the easy part, planking the bulwarks, I breathed a sigh of relief, but the planking wasn't as bad as I'd feared!

post-3-0-52608500-1361134716_thumb.jpg

 

post-3-0-31799700-1361134718_thumb.jpg

 

Now it was time for the fun parts, I completed the bow and added the capping rails:

post-3-0-72478000-1361134782_thumb.jpg

 

post-3-0-30439200-1361134784_thumb.jpg

 

Also the wales, rubbing rails and other decoration:

post-3-0-40351700-1361134786_thumb.jpg

 

post-3-0-33956700-1361134788_thumb.jpg

 

post-3-0-85959700-1361134789_thumb.jpg

 

post-3-0-55989500-1361134791_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Thanks a lot for reposting this, Caroline. I'm thinking about making the ship's boat, and your build has been very useful.

 

Tony

Link to comment
Share on other sites

Thanks for looking in on my log guys, your continued support is always welcome.

 

Now where was I? Ah yes, planking finished and decorations attached, I moved on to the guns and their carriages. As I mentioned in my first post, I didn't like the carriages provided, infact they were more like sleds, so after some discussion with other members and some research, I came up with a more probable design., based loosley on the Mary Rose cannon carriages. They were made out of balsa which was easy to carve, but also very fragile, but I liked the end results.

 

 

First prototype, unstained:

post-3-0-27292100-1361722140.jpg

 

First five stained and completed with rope bindings:

post-3-0-73418800-1361722150.jpg

 

Size comparison:

post-3-0-39805100-1361722141.jpg

 

In position on the deck:

post-3-0-83315600-1361722145_thumb.jpg

 

Next I painted the brass shields and decorations:

post-3-0-44775800-1361722137.jpg

 

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Next i added the little shaped posts and the rubbing rails and other bits and pieces on the hull:

 

post-3-0-19777300-1361722756.jpgpost-3-0-01012500-1361722759.jpgpost-3-0-09420400-1361722763.jpgpost-3-0-85403700-1361722764_thumb.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Next was making the balcony and rudder.

 

post-3-0-99629500-1361723020.jpgpost-3-0-22751500-1361723022.jpgpost-3-0-66370700-1361723023.jpgpost-3-0-07647600-1361723025.jpgpost-3-0-08394100-1361723026.jpgpost-3-0-88509600-1361723026.jpgpost-3-0-29533600-1361723031.jpg

 

And yes the brass pins were a little tight when it came to attaching the rudder, I'll remember to check that the next time! :rolleyes:

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

I didn't like the metal lantern either (what a surprise, what did I like? :rolleyes:;) ) so I made another from balsa:

post-3-0-34183700-1361723325.jpg

 

Next I varnished the hull in clear varnish:

post-3-0-81870900-1361723372.jpg

 

post-3-0-10555600-1361723374.jpg

 

Then came time to fit the balcony and its supports:

post-3-0-59246500-1361723376.jpg

 

post-3-0-52215300-1361723382_thumb.jpg

 

And the metal decoration at the stern:

post-3-0-70779500-1361723385.jpg

First Completed Build: San Francisco (Original Version)

Current build: Victory Models HMS Pegasus

Cross Stitch Project (Finished): Battle Of Agamemnon and Ca Ira

Cross Stitch Project : Victory & Temeraire

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...