closehaul Posted June 3, 2021 Author Share #91 Posted June 3, 2021 I started the running rigging for the downhauls (1st photo) for the staysail, jib sail and jib topsail starting at the belaying pin, reeving the line through each block made fast to the bowsprit with 26 gauge brass wire then through each block fixed to the fore top mast and down to and belayed on the fife rail (for the jib top sail only) and port and starboard bitts aft of the foremast for the staysail and jib sail downhauls. Next the lines for the peak halliards (2nd photo) were belayed at the starboard bitt aft the mast through an eye under the fife rail then relayed up and reeved between the 3 single blocks at the mast and the two bridle single blocks on the gaff then down to and belayed on the fife rail. The throat halliard is belayed on the port bitt and is reeved through triple and double blocks vertically up the mast and down to the fife rail. The topsail sheet starts and ends at the fife rail and reeved through holes (to simulate sheaves) drilled at the tips of the gaff and topmast. The third photo shows the fore boom sheet, outhaul and topping lift. Note that the vertical line running between tips of the boom and gaff is not an existing line. I put it there to indicate the leach of the sail as a suggested option in the instructions. schooner, Duanelaker, BobG and 2 others 5 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
closehaul Posted June 12, 2021 Author Share #92 Posted June 12, 2021 (edited) The running rigging has been completed (bottom photo) on the main and mizzen masts which are identical to the foremast from the previous post except for the mizzen sheet which is configured with heavier blocks and bitts for the spanker's large sail displacement (top photo). I failed to mention that the main deck furniture has been affixed in its place per the sail plan as each masts' entire rigging from the forward companionway back to the main cabin has been completed. There remains only the ships' boats flags, pennants and rope coils to be done before Atlantic is off the blocks. Edited June 12, 2021 by closehaul gieb8688, BobG, schooner and 3 others 6 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
BobG Posted June 13, 2021 Share #93 Posted June 13, 2021 What a fantastic job you are doing on this beautiful model, closehaul! mtaylor 1 Quote Bob Garcia "Measure once, cuss twice!" Current Builds: Hms Brig-Sloop Flirt 1782 - Vanguard Models Pen Duick - Artesania Latina 1:28 Completed: Medway Longboat 1742 - Syren Ship Model Co. Member of the Nautical Research Guild Link to comment Share on other sites More sharing options...
closehaul Posted June 14, 2021 Author Share #94 Posted June 14, 2021 On 6/13/2021 at 1:12 PM, BobG said: What a fantastic job you are doing on this beautiful model, closehaul! Thank you Bob for the accolades and the encouragement you’ve given me throughout the build and all others out there who’ve been commenting and reacting to the build of Atlantic. BobG 1 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
closehaul Posted June 19, 2021 Author Share #95 Posted June 19, 2021 I started the rope coils on an improvised jig for six flemish hands and 24 draping coils at a time. All coils must first have a drop of CA glue to harden the polyester line for cutting then dabbed with white glue mix to hold them to form. The flemish hand coil laid nicely on the main deck using the white glue mix to secure it in place. Once the CA hardens completely on the line between each draping coil (bottom photo) they will be severed then wrapped around their waist with a couple loops tied off and coated with white glue mix. When it drys the top pins on the jig can easily be pulled out and the coil can be placed onboard its pin. We'll see if this works out as good as it did for the Flemish hands in the next post. ccoyle, mtaylor, coxswain and 2 others 5 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
closehaul Posted July 11, 2021 Author Share #96 Posted July 11, 2021 Things were delayed on Atlantic with the holiday, out of town family and a new puppy (Buster) around the household. Rope coils have all been made fast upon the belaying pins and flemish hand coils to the deck. One note on making the coils with the polyester line is that every cut and trim required CA glue which slowed the process down. Surprisingly though the 50/50 mix of white glue & water kept every coil from unraveling yet pliable when hanging them from pins. The one problem I had with the hanging coils was tying off the line around the waist and binding the coil loops. I was only able to manage a few and the rest have to hang on the pins in an un-seaman like manner but I can live with this. bhermann, Ryland Craze, BobG and 3 others 6 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
BobG Posted July 11, 2021 Share #97 Posted July 11, 2021 5 hours ago, closehaul said: a new puppy (Buster) around the household. We need a photo of that new pup! gsdpic 1 Quote Bob Garcia "Measure once, cuss twice!" Current Builds: Hms Brig-Sloop Flirt 1782 - Vanguard Models Pen Duick - Artesania Latina 1:28 Completed: Medway Longboat 1742 - Syren Ship Model Co. Member of the Nautical Research Guild Link to comment Share on other sites More sharing options...
MrBlueJacket Posted July 12, 2021 Share #98 Posted July 12, 2021 Now that it's done, your customer file shows 10% off your next kit from us. Nic Quote Link to comment Share on other sites More sharing options...
closehaul Posted July 12, 2021 Author Share #99 Posted July 12, 2021 22 hours ago, BobG said: We need a photo of that new pup! Meet Buster! Ryland Craze, BobG, bhermann and 2 others 4 1 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
closehaul Posted July 12, 2021 Author Share #100 Posted July 12, 2021 7 hours ago, MrBlueJacket said: Now that it's done, your customer file shows 10% off your next kit from us. Nic Thank you Nic. Ordering kit now. Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
BobG Posted July 12, 2021 Share #101 Posted July 12, 2021 1 hour ago, closehaul said: Meet Buster! He's adorable! What kind of dog is he? Quote Bob Garcia "Measure once, cuss twice!" Current Builds: Hms Brig-Sloop Flirt 1782 - Vanguard Models Pen Duick - Artesania Latina 1:28 Completed: Medway Longboat 1742 - Syren Ship Model Co. Member of the Nautical Research Guild Link to comment Share on other sites More sharing options...
closehaul Posted July 13, 2021 Author Share #102 Posted July 13, 2021 14 hours ago, BobG said: He's adorable! What kind of dog is he? Shih tzu mix, adopted. BobG 1 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
closehaul Posted July 18, 2021 Author Share #103 Posted July 18, 2021 The first five photos are the final assembly steps. Atlantics' motor launch and owner's gig aft of the main mast on their davits and her jolly boats the fore of it. The second photo is the anchor tackle and davit. The third, masthead pennants and the US yachting ensign off the mizzen gaff. The stern and bow decals; the fourth and fifth photo. The final ten shots are of Atlantic finished, the last two photos in her display case and moored snug in the living room. Atlantic was the challenge I needed while sheltered in during the pandemic and proved to be that and more. Even with all the inconsistencies that made me quite aware of my skill level, I couldn't be any prouder to display her as the centerpiece in the main salon. Most of all my acknowledgements to the Admiral for her provision of time, working space, and listening to my frustrations and profanities during the build, her critiques exceeded only by her encouragement, patience and graciousness. Also In the encouragement department my appreciation to Bob G on his supportive comments to my own doubts and the contributions from his build of PenDuick. Nic of Bluejacket Shipcrafters whose advise and remedial input were indispensable, and everyone else who reacted and commented on Atlantics' build. Finally to modelshipworld which made it possible to acquire new modeling skills through their extensive data base. My next Build will be the schooner America in the same scale as Atlantic starting around late fall. Ciao Everyone! David Lester, etubino, yvesvidal and 8 others 9 2 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
gsdpic Posted July 18, 2021 Share #104 Posted July 18, 2021 Congratulations on completing this fine build! You certainly deserve to be, and have every reason to be, proud of this accomplishment! BobG and closehaul 1 1 Quote - Gary Current Build: Artesania Latina Sopwith Camel Completed Builds: Blue Jacket America 1/48th Annapolis Wherry Link to comment Share on other sites More sharing options...
closehaul Posted July 18, 2021 Author Share #105 Posted July 18, 2021 (edited) On 7/18/2021 at 1:29 PM, gsdpic said: Congratulations on completing this fine build! You certainly deserve to be, and have every reason to be, proud of this accomplishment! Thank you Gary. Your build of the schooner America concurrent with Atlantic was motivating especially when I was hung up on the anchor placement. -Ange Edited July 19, 2021 by closehaul poor composition BobG, Ryland Craze and gsdpic 3 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
markjay Posted July 18, 2021 Share #106 Posted July 18, 2021 Very nice job! Ryland Craze, closehaul and BobG 2 1 Quote Mark Phoenix, AZ Current builds; Previous builds, in rough order of execution; Shipjack, Peterbrough Canoe, Flying Fish, Half Moon, Britannia racing sloop, Whale boat, Bluenose, Picket boat, Viking longboat, Atlantic, Fair American, Mary Taylor, half hull Enterprise, Hacchoro, HMS Fly, Khufu Solar Boat. On the shelf; Royal Barge, Jefferson Davis. Link to comment Share on other sites More sharing options...
closehaul Posted July 18, 2021 Author Share #107 Posted July 18, 2021 (edited) 23 hours ago, markjay said: Very nice job! Thank you Mark. Here’s to success on our next builds.-Ange Edited July 19, 2021 by closehaul Poor composition Ryland Craze and BobG 2 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
Ryland Craze Posted July 18, 2021 Share #108 Posted July 18, 2021 Very nice model. Congratulations on completing this fine build. BobG and closehaul 1 1 Quote Ryland Member - Hampton Roads Ship Model Society - Ship Model Society of New Jersey - Nautical Research Guild Current Build - Armed Virginia Sloop, 18th Century Longboat Completed Build - Medway Longboat Link to comment Share on other sites More sharing options...
schooner Posted July 19, 2021 Share #109 Posted July 19, 2021 Congrats on a wonderful build! It's probably safe to assume that you spent more time building this model than the yacht owners ever spent onboard the real thing. BobG and closehaul 1 1 Quote Tim Current build: Continental Navy Frigate ALFRED (build log) Past builds: Steam Tug SEGUIN (build log in the kits 1850-1900 section) Liberty Ship SS Stephen Hopkins (Gallery & Build Log) USS Basilone (DD-824) (Gallery & Build Log) USS Olympia (Gallery) USS Kirk (FF-1087) (Gallery & Build Log) Link to comment Share on other sites More sharing options...
closehaul Posted July 19, 2021 Author Share #110 Posted July 19, 2021 (edited) 14 hours ago, Ryland Craze said: Very nice model. Congratulations on completing this fine build. Thank you Ryland for the compliment. The basic reason I choose Atlantic for a build was the aesthetic form of her hull. Regards, Ange Edited July 19, 2021 by closehaul Ryland Craze and BobG 2 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
closehaul Posted July 19, 2021 Author Share #111 Posted July 19, 2021 (edited) 35 minutes ago, schooner said: Congrats on a wonderful build! It's probably safe to assume that you spent more time building this model than the yacht owners ever spent onboard the real thing. I appreciate the compliment Tim. I actually thought Atlantic would be finished before spring not mid summer. Thank you, Ange Edited July 19, 2021 by closehaul Ryland Craze 1 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
BobG Posted July 19, 2021 Share #112 Posted July 19, 2021 Congratulations, closehaul! She's absolutely beautiful and your excellent craftsmanship and attention to detail is clearly on display now. The sleek lines of the Atlantic with her 3 masts are wonderful. It's one of my favorite models which just may have to be on my ever lengthening wish list. I look forward to your build of the America which is another sailing ship that I love as well. Have you decided which America model you will be building? Thank you for your kind words also. My Pen Duick has been on pause for far too long but I am determined to finish her. Ryland Craze 1 Quote Bob Garcia "Measure once, cuss twice!" Current Builds: Hms Brig-Sloop Flirt 1782 - Vanguard Models Pen Duick - Artesania Latina 1:28 Completed: Medway Longboat 1742 - Syren Ship Model Co. Member of the Nautical Research Guild Link to comment Share on other sites More sharing options...
TBlack Posted July 19, 2021 Share #113 Posted July 19, 2021 I read the first entry of your log; the trepidation comes through pretty clearly. You did it! And she looks beautiful! Stick your chest out, big guy! Tom Ryland Craze and BobG 2 Quote Link to comment Share on other sites More sharing options...
closehaul Posted July 19, 2021 Author Share #114 Posted July 19, 2021 (edited) 4 hours ago, BobG said: Congratulations, closehaul! She's absolutely beautiful and your excellent craftsmanship and attention to detail is clearly on display now. The sleek lines of the Atlantic with her 3 masts are wonderful. It's one of my favorite models which just may have to be on my ever lengthening wish list. I look forward to your build of the America which is another sailing ship that I love as well. Have you decided which America model you will be building? Thank you for your kind words also. My Pen Duick has been on pause for far too long but I am determined to finish her. Thank you Bob for the compliments and also your encouragement throughout the build of Atlantic. The Bluejacket America kit that arrived a couple days ago is the 1/8" scale model. My choice of this scale is two fold. First, I like to have a famous schooner in the same scale as Atlantic for comparative display. Second and more importantly is the fact I had never assembled a plank and frame (or bulkhead) hull before. Bluejacket rates the 1/8" model as requiring less experience than the larger 1/4" scale America which will facilitate my novice level for the plank and frame hull assembly. After I have cut my teeth on America, my long range aspiration is for a larger plank and frame vessel, possibly a warship. Ciao Bob! -Ange Edited July 19, 2021 by closehaul poor composition BobG and Ryland Craze 2 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
closehaul Posted July 19, 2021 Author Share #115 Posted July 19, 2021 1 hour ago, TBlack said: I read the first entry of your log; the trepidation comes through pretty clearly. You did it! And she looks beautiful! Stick your chest out, big guy! Tom Thank you Tom. When I first opened the box and seen all those tiny parts Got a lump in my throat the size of an apple. Persistence was the key from there on out. -Ange BobG and Ryland Craze 2 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
PRS Posted July 19, 2021 Share #116 Posted July 19, 2021 Man those rope coils look fantastic! the pup looks sweet too closehaul, Ryland Craze and BobG 3 Quote Paul Current Build: HMS Winchelsea 1764 1:48 Completed Build: HM Cutter Cheerful-Syren Ship Models 1/48 Completed Build: Artesania Latina Bluenose II Completed Build : Lady Nelson Link to comment Share on other sites More sharing options...
closehaul Posted July 20, 2021 Author Share #117 Posted July 20, 2021 (edited) 22 hours ago, PRS said: Man those rope coils look fantastic! the pup looks sweet too Thank you PRS. The flemish hand coils laying on deck were a joy to do. Buster and I have become thick as thieves. Regards -Ange Edited July 20, 2021 by closehaul Ryland Craze 1 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
bhermann Posted July 20, 2021 Share #118 Posted July 20, 2021 She is a beauty and belongs where she is, proudly displayed as the center of attention. Looking forward to your next journey with America! Bob Ryland Craze 1 Quote Current build -- MS Bluenose Future build - MS Flying Fish "A ship is safe in harbor, but that's not what ships are for." - William G. T. Shedd Link to comment Share on other sites More sharing options...
closehaul Posted July 20, 2021 Author Share #119 Posted July 20, 2021 2 hours ago, bhermann said: She is a beauty and belongs where she is, proudly displayed as the center of attention. Looking forward to your next journey with America! Bob I’m grateful for you compliment and interest in my next build of America this fall. -Ange Ryland Craze 1 Quote Completed builds - Atlantic Link to comment Share on other sites More sharing options...
Landlubber Mike Posted July 20, 2021 Share #120 Posted July 20, 2021 (edited) Ange, I'm sorry to have missed your log but wow, what a beautiful model! Fantastic job! Love the display case too. Can I ask - did you use dry transfer letters for the name? The lettering looks perfect! I'm trying to figure out what to do on my Charles Morgan but the name is so long that I worry about having the letters oriented the same/right way. Edited July 20, 2021 by Landlubber Mike closehaul 1 Quote Mike Current Wooden builds: Amati/Victory Pegasus MS Charles W. Morgan Euromodel La Renommèe Plastic builds: Hs129B-2 1/48 SB2U-1 Vindicator 1/48 Five Star Yaeyama 1/700 Pit Road Asashio and Akashi 1/700 diorama Walrus 1/48 and Albatross 1/700 Special Hobby Buffalo 1/32 IJN Notoro 1/700 Akitsu Maru 1/700 Completed builds : Caldercraft Brig Badger Amati Hannah - Ship in Bottle Pit Road Hatsuzakura 1/700 Hasegawa Shimakaze 1:350 F4B-4 and P-6E 1/72 Accurate Miniatures F3F-1/F3F-2 1/48 Tamiya F4F-4 Wildcat built as FM-1 1/48 Special Hobby Buffalo 1/48 Eduard Sikorsky JRS-1 1/72 Citroen 2CV 1/24 - Airfix and Tamiya Entex Morgan 3-wheeler 1/16 Terminated build: HMS Lyme (based on Corel Unicorn) On the shelf: Euromodel Friedrich Wilhelm zu Pferde; Caldercraft Victory; too many plastic ship, plane and car kits Future potential scratch builds: HMS Lyme (from NMM plans); Le Gros Ventre (from Ancre monographs), Dutch ship from Ab Hoving book, HMS Sussex from McCardle book, Philadelphia gunboat (Smithsonian plans) Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.