Jump to content

La Mahonesa by KLarsen - Scale 1/48 - stern cross-section


Recommended Posts

Very nicely done! Can't believe it is your first POF and you started with the stern section, probably the most challenging part of the hull :) 

Link to comment
Share on other sites

10 hours ago, Mike Y said:

Very nicely done! Can't believe it is your first POF and you started with the stern section, probably the most challenging part of the hull :) 

Thanks! That's exactly why I chose the stern, if I can build that I can build the whole ship 😄

Link to comment
Share on other sites

Such a nice looking model.  You are really doing a fine job.  I will be following along.

Link to comment
Share on other sites

6 hours ago, dvm27 said:

You know, you could just scarph that keel joint and add the midsection and, if that goes well...

Hahaha, trust me, I've thought about it 😂

Most likely though my next project will be La Diligente, a french tartane from the Ancre monograph. Lateen sailed boats are my favourite so it's something I'd like to "specialise" in.

 

6 hours ago, Chuck said:

Such a nice looking model.  You are really doing a fine job.  I will be following along.

Thank you! 😊

Link to comment
Share on other sites

Hello, I am of the same opinion as KLarsen and before starting a long-term project of a complete ship, with all that it implies (time, money...) I must know if I have the minimum and necessary skills to solve complex and important issues and not have a lot of wood for firewood. I have read some threads in which problems have made them abandon the project. There are people who are just starting their tests like KLarsen and others like me who have been trying for a long time

Congratulations KLarsen, I have been following your project and it is great

Link to comment
Share on other sites

After posting the pictures the other day I found out I'd installed the lower decks clamps a little too high up, though I was able to remove them using a hair drier and reinstall them a little lower. I also installed the thickstuff (I think they're called?), the 2 x 3 planks running along the inside. This is most likely all the inner planking I'll add.

PXL_20240816_180820163.thumb.jpg.4e96408158a3fc888884b56cfa158b31.jpg

I also added nails on the upper bulwarks. I used 0,3mm copper wire here, the 0,5mm I've used elsewhere seemed a little too think for these planks.

PXL_20240816_180017434.thumb.jpg.6e0a79a55f247eed0b4feed942cc3d78.jpg

With this I can get started on the decks, first will be the platform in the bottom where the powder room is. I've yet to decide how many bulkheads I'll install, I want the interior to be visible while also giving an idea of how cramped it was.

 

Again, thanks everyone for the kind comments and likes, it's much appreciated! 😊

Link to comment
Share on other sites

  • 3 weeks later...

It's finally time to get started on all the interior stuff. I've installed the platform for the powder and munitions room, and today I finished the bulkhead between the powder room and the lantern room. I won't be adding any glass in the panes, I think that'll just distract from the look.
I'm really happy with how the window turned out, if I can do as well with the big stern windows I'll have no complaints!
The only thing I'm not happy with is how the inner planking terminates at the very stern; it was difficult to bend them and almost impossible to sand them there. However, most likely it won't be seen at all when the bulkheads and deck planking is in place. It's always nice when you can just hide your sloppy craftsmanship! 🤣
PXL_20240826_140030536.thumb.jpg.41fcf277ee37d2b2ccb32a7bbcc2797f.jpgPXL_20240901_145331889.thumb.jpg.06844fc0a051cf193191dd3dcaa0c8b6.jpgPXL_20240901_145511521.thumb.jpg.0268ced26ecfa7b9a792684618cbfc21.jpg

Link to comment
Share on other sites

  • 4 weeks later...

I'm finishing the munitions and lantern room and planking the platform above them. I haven't decided if I'll fully plank that deck or not, planking it will completely hide the lantern room but will make it easier to install the bulkheads above.
I'm also fitting the beams for the orlop deck which are necessary to install the pillars supporting the mizzen mast. It really is a puzzle finding out which pieces to install and when.
The deck is planked with wooden nails but they are hardly visible (like on a real deck).
PXL_20240928_163215199_MP.thumb.jpg.9868886e7dabb2c40e9640d9649e74da.jpg

Link to comment
Share on other sites

  • 2 weeks later...

I decided to go ahead and fully plank the platform as well as install all the panels separating the rooms and corridors.

I'm well aware that it'll hide a lot of the details like the lantern room, but it seemed the best way to show how cramped the ships interior was.

I'll also install the bulkhead behind the platform (the lower plank is already in place) even though it will completely hide the sail room behind.

PXL_20241011_173557787.thumb.jpg.37f2862e04fc80fa5c5d4d689a45504f.jpgPXL_20241012_164906529_MP.thumb.jpg.f0390bd087b1d146389dfafe5447c0ed.jpgPXL_20241012_165140499.thumb.jpg.04d8236677e769644e01ff5ded0ea945.jpg
With this, I can install the last deck beams for the orlop deck and decide how much to plank it, whether entirely or just a few planks.

Link to comment
Share on other sites

While I won't be installing any LEDs I couldn't resist simulating the light coming from the light room.

PXL_20241016_204644135_1.thumb.jpg.7b65b6885525fbc219373c81e755b337.jpg

Also, I installed the last deck beams for the orlop deck. Now comes the difficult task of creating the crazily curved waterways. I'll probably have to cut it from a sheet as there's no way I'll be able to bend a strip to follow those curves at the stern.

PXL_20241016_115527870.thumb.jpg.2f5e44ca47c3ad8bb571e7f920d3a637.jpg

Link to comment
Share on other sites

  • 2 weeks later...

To create the waterways for the orlop deck I first built up a template from thick crafting paper, then cut out the piece from wood and shaped it. It was the only way I could think of to get the complex curves correct.

The plans don't show how the deck planks would be fastened at the very end, so I created a small piece and put it on the deck clamp. It's far from perfect but it won't be possible to see it once the deck is planked.

I'll most likely plank the whole insides of this deck up to the main deck clamp, including the stern. Especially because I don't like the way the stern is looking right now where you can see the back of the outer planking.

PXL_20241026_164416020_MP.thumb.jpg.1568ae425ebbe6e30867aeb7697e0ff7.jpgPXL_20241026_164446714.thumb.jpg.c21beb9034e6526da7f6a151482d62b0.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...