Jump to content
MSW Spring Donation Drive

druxey

NRG Member
 View Profile  See their activity

  • Posts

    12,403

  • Joined

  • Last visited

 Content Type 

Everything posted by druxey

  1. druxey
    That's the good thing about poor castings - no waste! Back into the melting pot they go. That is a graphic demonstration of the use of talc, BTW. I think that the stiffer Hydrostone mix would probably be OK. I usually dry my casts in a warming oven. That drives off the moisture more quickly than simple air-drying. Make sure that it is only just warm, not hot!
  2. druxey
    I suspect that an expert builder like Michael will use fillers, Dan.
  3. druxey
    If tapping on a lathe, surely turning by hand and not under power!
  4. druxey
    Actually, miniature left-hand taps and dies are available - if you are prepared to pay the price!
  5. druxey
    I think that you have done a fine job there, Kortes!
  6. druxey
    Love the 'same angle' photos of the ship and comparison to the model, Dan.
  7. druxey
    Interesting and tricky technique! Thank you for sharing this, Kortes.
  8. druxey
    Great come-back, Carl! Thank you. But, we digress....
  9. druxey
    Usually on merchant craft there were no limber boards or channels above the floors. The drainage channel consisted of notches in the floors on their undersides, next to the garboard. Water flowed along under the frames, along the garboards, to the lowest point in the ship. Bilge water was then removed by the pumps.
  10. druxey
    That flower pot seems to be 'clogged' up with earth! Sorry, I couldn't help that.
  11. druxey
    Laminated wood need an odd number of layers (3, 5, 7, etc.), each layer with grain at right angles to the next. Or - well, you've already discovered the result! A simplified frame structure such as shown above will work. It's a bit wasteful of wood, though. Do you have any way of modifying and controlling the humidity in the home? Where I live we need a humidifier in winter and A/C in the summer.
  12. druxey
    Certainly the result was worth the effort, Vaddoc.
  13. druxey
    Nice, Kurt, if you can make functional scale turnbuckles!
  14. druxey
    Nice going, Bill!
  15. druxey
    Glad the walnut hoops worked out for you in the end.
  16. druxey
    How disappointing! My first suspicion would be that the wood was improperly dried or poorly seasoned. Either that, and/or the log the wood was not quarter cut. In my own experience, wood will move where it wants to. You could try the remedy suggested above, but this may prove to only be a temporary solution. In 'real' boats, wood grain more or less follows the contour of the frame which is built in sections. There are no cross-grained areas. This gives maximum strength, as well as minimizes the problem of warpage. Perhaps you might want to rethink how you are going to construct your model.
  17. druxey
    That's a very useful 'how to', Frank. Steel wire is a beast to work with!
  18. druxey
    Lovely work with the brass fittings! Had you considered rolled paper for mast bands, then painting them? Walnut is certainly unsuitable for the job.
  19. druxey
    Well, Bob is almost correct; but once you lick the cotton swab, you don't put it back in your mouth again! Or, if you do, you will only do it once.... I would only add that if you take the time and trouble to restore the model, put them in cases; or they will simply get dusty and damaged again.
  20. druxey
    Perhaps we can advise you better if you can post some photos of their condition to begin with.
  21. druxey
    You wrote: " I needed to walk away and shake my head clear a few times, review a number of books and re-read passages many times. This is the kind of stuff that cranks me up and gets me jumping for more! Yes I really enjoyed it that much." Oh, you've got it bad, Alan!
  22. druxey
    Barque? Schooner? Why not a Scuaque (as in The Hunting of the Snark)?
  23. druxey
    Nice to see you back in the saddle after your move, Bill! Looking forward to seeing further progress soon.
  24. druxey
    I think what you are seeing is the edge of the bearding back or bevel that allows the rudder to turn freely. It is not a separate part.
  25. druxey
    Lovely, Ed, simply lovely.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...