-
Posts
3,852 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by KeithAug
-
HMCSS Victoria 1855 by BANYAN - 1:72
KeithAug replied to BANYAN's topic in - Build logs for subjects built 1851 - 1900
Excellent Pat. Not sure how it is possible to clean a workshop in a few days. Certainly mine would be more of a project.- 993 replies
-
- gun dispatch vessel
- victoria
-
(and 2 more)
Tagged with:
-
Thank you for clarifying. I asked because it wasn't unusual to plate over this type of gun emplacement as generally they were of very little use in anything other than calm weather.
-
I made a start on the launch. I don't have the section lines for the hull so i needed to create these. In the following photo I have coloured in the points / lines that I could deduce from various photographs. I had a fairly good side view from which I could take the keel, waterline, and deck lines. I also had a fairly good picture of the stern and I had a dimension for the maximum beam. From this information i made a guess at the vertical section lines and then plotted the horizontal section lines. I then drew best fit curves to form the horizontal sections and transferred these back on to the vertical sections. I then smoothed the vertical section lines and plotted these back on to the horizontal sections. I iterated around several times until both horizontal and vertical section lines formed smooth curves. I then cut 1/8" plywood frames and glued on the section drawings. I then cut slots in each of the frames to take the keel. All of the frame blanks had been cut accurately to exactly the same size thus facilitating accurate cutting of the slots on the table saw. The frames were then cut out using a scroll saw. A piece of scrap wood was then slotted to take the frames and the frames were glued in pace with a keel piece maintaining alignment. Prior to fairing the frame edges were highlighted with a permanent marker. Balsa blocks were then glued in at the bow and the fairing was done with a sanding block. The position of the engine was then determined by plotting the line of the prop shaft. The bulkhead for the transverse seat position was then installed (1 frame rearward of the actual position). The stern bulkhead on the launch is quite thick so the aft most bulkhead was widened to reflect this. Finally these additional bulkheads were sanded to match the fairing of the other frames. Small hulls are much quicker to make than big ones. I must remember this thought.
-
Wonderfully precise and technically competent clinker planking job Gary. Beats my usual suck it and see approach hands down.
-
You really do crack on. Amazing speed and quality as well.
- 180 replies
-
- pilot boat
- Elbe 5
-
(and 3 more)
Tagged with:
-
Druxey - not quite sure what you mean but it is definitely the boats wheel. Hakan - I think my preference would be to invest in a couple of extra pulleys. Eberhard - I have not seen the 3 D printed engines - must look them up.
-
Thank you Gary. I am planning to cheat a little. The left hand arrow is pointing at the boats wheel. This is actually aligned fore and aft which I can't really get my head round. I suppose the crew get used to it but to me it is daft (never seen one on a car for instance). I think I am going to have to mount it on the bulkhead just in front of it. The right hand arrow is pointing the the seat under which the engine is mounted. Every time I see you guys building engines I get jealous so I am going to move this seat rearward and put an exposed engine in the launch. I know the launch should have a modern Volvo Penta but I think the owner has manage to source a 1920's twin pot petrol engine, that i think is more in keeping. I hope that going a bit of piste won't get me banned from MSW.
-
I somehow missed the completion. One of the most unusual models i have seen but nevertheless quite charming. Very well done.
-
A picture is worth a thousand words. Cairo looks amazing. Workspace is a 5/10 which is better than my usual score.
-
Brian Re - I happened by the Admirals craft room where she was hard at work making stencils for T-shirt on her Cricut. I need one of those. Must get my wife into making stencils for T shirts then I can buy her one for Christmas. Also I am always amazed that the photographs of your work space and model never have a speck of dust on them. How is this possible?
-
Thank you for commenting Michael, Richard, Pat, Keith, Druxey and Eberhard. Also thank you to everyone who has visited and liked my work.
-
Very nice little restaurant on the east coast of Just Van Dyke i recall. I was there in about 2005 - generally very nice but we found the sailing was a bit constrained by the closeness of the islands. Great snorkelling at RMS Rhone and at the Baths on Virgin Gorda. On the negative side we found the BVI's a bit over run by noisy catamaran gin guzzler types.
-
Eberhard, Sometimes they sail with it on deck. And sometimes they don't. They also seem to spend a deal of time sailing with it replaced by a dinghy. It must increase the C of G and reduce the metacentric height (while also increasing the starboard list). My guess is they take it with them on position cruises and then land it and rely on the dinghy while racing or cruising within the local area. I will also be making the RIB which sits on the port side.
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.