thibaultron

Yes, the pool is full of water, and yes, he is barefoot!

 

After the first Iraq war the Iraqis set many of the oil wells in the occupied countries on fire as they retreated, prompting stories of the coming apocalypse of the wells burning for decades, as there were so many, and standard methods took a lot of time per well. Well as you can see that didn't happen. One of the most innovative ways to put them out, was a Polish (I believe) company that thought way outside the box, and built a frame with one or two jet engine mounted with the exhaust pointing toward the rear. They would back the running engines toward the flames and the oxygen poor massive flow output would smother the flames, while massive amounts of water cooled the metal end of the well, so the oil would not be reignited,

Well, thanks! I can now remove that one from my wish list on Amazon! Glad It didn't waste my money on it!

I too had chemistry sets as a child. I bought one for my son in the early 90s. They had made it so safe (most of the chemicals were bottled as pads "Soaked" in the chemicals, rather than liquids) that we could not get any of the experiments to work! I took chemistry classes in both high school and first year of college, so had a decent idea of what we were doing, still no luck.

You may also want to get Badger's Regdab, or what ever their name is spelled backwards. It is a solution you dip your needle in to help keep the paint from drying on it. Dip the needle and wipe it off. It will leave a film that lasts for a while.

As to the accuracy of the boat. He pulled the design from a reputable source, and apairently the Santa Maria replica has one.

Pavel Nikitin (https://shipsofpavelnikitin.com/shop) is a ship kit manufacturer in the Ukraine that makes a series of well designed laser cut wooden ship and small boat kits.  This kit is a 1/48^th scale (136mm length) model of, I believe, a ship's boat from the Santa Maria from plans by H. E. Adametz. The kit costs ~$20 US, He also produces a larger 1/24^th scale (272 mm Length) kit with mast and sail “The “Santa Maria” Caravel Boat” for ~$66 US that looks to be the same boat as this smaller kit, sans the mast and sail.

 

The kit comes in a small box about 6 inches long.

 

 

Opening the box there are a four page set of plans/pictorial instructions, and two plastic wrapped packages of laser cut wood parts.

 

 

The instruction sheets have pictorial type instructions similar to a plastic kit. There are no written directions, so some modicum of wooden ship model knowledge is needed. Perusal of a few build logs on this forum, would provide the needed knowledge.

 

Here are pictures of the cover sheet and a sample page of the instructions.

 

 

The kit is built upright, in a cradle, the parts for which come in one of the wooden packages.

 

 

Opening the bundle of the parts for the boat itself reveals 7 sheets of laser cut parts. Sheets 1 through 6 and sheet 9. I’m assuming the sheets 7 and 8 are the cradle parts, thought these are all separate parts, not two sheets of parts.

 

Sheet 1 has the keel, stem, stern post and display cradle parts.

 

 

Sheet 2  has the frames, stern, and some smaller parts. The frames have secondary lines for beveling the frames before installation for the initial fairing of the hull.

 

 

Sheet 3 has the engraved planking for the final stern layer, the gunnels, seats, and floor.

 

 

Sheet 4 has more frames, small parts, and the rudder.

 

Sheets 5 and 6 contain the pre-cut planking.

 

 

Sheets 7 and 8 are the parts for the construction cradle.

 

 

Finally Sheet 9 has the oar blanks.

 

 

The kit has no metal parts, but other than perhaps rudder pintles, which can be made from paper, you really don’t need any for this small model.

 

This kit should build a nice display piece for a small space.

 

 

My kit arrived two days ago!

As an added note, one of the survivors was the Bismarck's ship cat, who the crew kept, and named Unsinkable Sam. When the cruiser was later torpedoed and sunk, the cat again survived. He then was put on another ship, which was also sunk, and survived again. After that he was sent to an old folks home, where he lived out the rest of his life comforting the patients.

Having looked at the Constitution photos above, it seems to me that the seams are invisible, when first coppered, and only really show once the weathering gets advanced and the seam lines pop out, like on a weathered aircraft..

For the char, you can scrape it off with a blade held perpendicular to the surface. Its faster and removes less material.

Leave the parts clamped for several days, so that they completely dry in the clamped position. I know that you want to get right back to the model, but you will waste much more time fighting the warps later. For scribing the deck, I use the tip of a razor saw drawn along a straight edge to grove the lines. Be careful to pull the tip so the grain of the wood pulls the tip into the straight edge. If it wanders out of line stop and run your finger nail over the mistake to flatten the wood back down. When done run a pencil along each line, erase any mistakes. Then sand lightly. A clear finish will seal everything (varnish, or even thin CA spread with a bit of cardstock). On my RC Warships, the Ca coating has held up over 30 years. Do the scribing before installing the deck.

If the metal primer is enamel it should be alright, avoid lacquer based ones on plastic.

As long As it goes on with a lot of build up it will work well.

CA glue or epoxy to attach the wood and metal parts to the resin. Primer is needed for the resin and metal, if using acrylic paint.  As to wood sealer, someone else will have to chime in.

Soak the hull in IPA for a while, this generally will soften and remove most paints.

Might I suggest, if the trusses are going to line up with the vertical studs, widening the bottom of the truss and running it down 3" or so and screwing it ti the stud. You could also run a straight strap across the side of the stud, and the side of the truss, instead of screwing through the edge of the plywood. This would solidly tie them together, and lock them from allowing the base to spread. Not being famillar with UK weather, I don't know if you have to deal with snow loads or not.

For the intermediate trusses, are you going to build actual trusses, or just place rafters? If just individual rafters, it would be much quicker to just measure and cut them in place. Cut a board a little long, drop it in place above the wall and center ridge beam, then run lines onto the board with a straight edge. This will also take into account any warpage in the walls. This should take a fraction of the time to design the rafters.

Try Vallejo or Tamiya acrylic paints. The tube stuff is craft paint, with a much larger "grain" size than the true model paints. With acrylics you need to prime the plastic, before the color coats go on. You also need to wash the pieces in soapy water, rinse, and then use gloves until the painting is complete. The oils from your fingers can cause adhesion problems with the water based paints. Vallejo sells two types of paint, Model Color (for brush painting) and  Model Air (for airbrushing). The Model Air is already thinned for airbrushing, though you still may have to add thinner. It depends on temperature, humidity, and airbrush type and air pressure. Acrylics dry much faster then the old style enamels, so you have to work a little faster with the airbrush. YouTube has many airbrushing videos, that can help you if you want to use one.

 

Vallejo's Primers don't sand well. I use Stynylrez primers from Badger. Their Red Brown is perfect as the red anti-foul paint color, without having to use an additional color coat. Note that I bought both the Model Color and Model Air Hull Reds, before I found the Stynylrez primers, and they are a slightly different shade of red. I bought them several years ago, so they may have corrected this. The Stynylrez primers are made for styrene, vinyl, and resin, I don't know how well they work on metals. For wood, no primer is needed.

 

Here are a couple of links that are helpful:

 

The Barbatos Rex YouTube Channel

 

And an Interview with the Owner of Badger Airbrush Company, which is very informative. Note that in this video, he says that all the manufactures buy their airbrush compressors from the same factories in China, and that, unless you want the Brand Name Tag, buy the cheaper Chinese brands.

 

 

 

My heating system has a self regulating mobile heating unit system! The colder the room gets the more mobile units move to your location.

Mine has been sitting in the New York USPS import station for the last 10 days! Hurry up and send it to me NY!

For fine detail, you need a resin 3D printer. I have a 4K resolution one, and I'm presently printing passenger car sides in HO (1/87.1), with well defined scale 1" hemispherical rivet heads and 1/4" layers between steel side and trim.

What flux is that? I have a large number of HO track switches to build, that will be soldered to PC board ties, during construction. A nice cleanable well working flux would be helpful.

Welcome!

https://nscaleships.com/n-z-scale-ship-index/hulett-automatic-unloader/