Jump to content
MSW Spring Donation Drive

Timmo

Members
 View Profile  See their activity

  • Posts

    602

  • Joined

  • Last visited

 Content Type 

Everything posted by Timmo

  1. Timmo
    Thanks joe. It's a fine kit with just a bit of extra difference in the way of the mortars and the bling on the stern. I'd highly recommend it.
  2. Timmo
    Very clean build you've got there joe. Nice work.
  3. Timmo
    Nice work Chris - as always
  4. Timmo
    Thanks Alistair and very poetically put. Nice weekend for the crossing. Bet you could almost see your house from there. Irony is next on the agenda is shaping and installing swivel gun pedestals and then installing the carriage guns- read repetitive. But the head rails were always the bit I anticipated would cause the biggest block in construction and that's because I wanted to give it a bit extra. That's how we learn.
  5. Timmo
    The vertical timbers of the head rails were made up from some curved pieces of ply from the kit that were unused from the hair brackets. In a technique copied from Mitsuaki Kubota's fine Bellerophon build they were painted blue and some half mm walnut were laminated to the sides. This was sanded back to give a nice edge. Careful shaping ensured a close fit. The centre hair brackets running horizontally between the upper cheek and upper rail have been made up and painted and await cutting and fitting to slot between the verticals. I'll be glad when this lot is finished.
  6. Timmo
    That's a result to be proud of Augie. The stern looks fantastic. This kit is heading to near the top of my wish list due to yours and Ben's efforts.
  7. Timmo
    With all the changes to the head rails the bowsprit was temporarily fitted and gammoning applied to make sure there was nothing that would be in the way later. A small but nerve wracking addition was the hawse holes. I added a reinforcing plank between the cheeks as per AOTS and as a result thinned down the bolster a bit and rounded the top and semi circle edges. The bolster was held in place while holes were marked with the flat end of the 3.5mm drill bit dipped in paint. A smaller pilot hole was drilled first before the larger one. This was done with a Dremel. The bit was too long and had a little bit of wobble making the hole slightly bigger than I would have liked but nothing major. Tape on both faces prevented splintering which was my big fear. Not a lot of second chances with this area. Now the final centre head rail can be knocked up.
  8. Timmo
    Aww ok then , that's pretty good but I reserve the highest praise four your work in wood.
  9. Timmo
    Brilliant work as ever Danny. Just when I thought it couldn't get any better you knock up a ships wheel! Inspirational stuff. Great to see something next to a coin I can relate to for scale.
  10. Timmo
    Hi Jason, thanks for the comments. yes I would seriously consider boxwood or another timber next time. This is my second kit so was started without much consideration for materials etc and I've learned a lot since about the splintering and grain properties of walnut. Looking at the head rails especially I think they could have been a lot neater with a different timber but cost is a consideration so depending on what I embark on next I may be stuck with it yet.
  11. Timmo
    Too kind chaps. Thanks
  12. Timmo
    The head rails had a centre section carved out to created raise prfofiles on either side. It's a little rough thanks to the file slipping and he grain on the walnut but it'll do. The centres were painted up to match the rest Two part epoxy was used to attach the head rails. It claimed a setting time of 4 minutes but was more like an hour resulting in a lot of smearing to remove and paint over later. While the epoxy was out the remaining stern figures were added. The castings are not quite symmetrical so bit of gentle pressure bent them on the right angle to have their heads resting against the taffrail. The bases they rest on had the edge facing the hull shaped to fit neatly. The wee dolphin carvings were set further back towards the stern than the kit instructions show. According to AOTS Granado they are almost a continuation of the stern carvings. His majesty's bomb vessel Granado as she now stands
  13. Timmo
    Thanks, Alistair, Andy, Jason and all.
  14. Timmo
    More top rigging there Jason. Nice work
  15. Timmo
    Autumn is in the air for today's spell in the garage shipyard. The dregs of cyclone Lusi pass overhead bringing a gusty wind and spot of rain from the dark sky. A porter ale in hand to match the mood and On to the port headrail/ cathead knee. Symmetry is the issue here. A trace of the one already completed onto paper and a fold to invert the image to proved a template to help with the other side piece. The same method of Dremel, bench sander, file and sandpaper was used to and shape the piece. Plenty of test fitting is the order of the day. The largely finished piece, right, compared to the other. None fixed as yet. I was a bit too vigorous on it and snapped it. Easily glued back together but that spells the end of progress today while the glue sets.
  16. Timmo
    That's right Alistair, making one of something is always possible, but two the same is the issue. The other might take a bit longer as I grapple with symmetry . No turning back now since I've cut notches in the sheer rail.
  17. Timmo
    Just found your build Denis. Nice work on it all and especially the flag trick.
  18. Timmo
    A couple of bits of walnut offcuts from the kit were laminated together and cut to shape for the upper head rails. The shape was marked off the cardboard templates and the outline cut. First the outside then the inside. Constant checking ensured a reasonably snug fit to the hull, the cat head and a consistent curve. A Dremel with a sanding head followed by files and sandpaper was used to shape the piece. Notches were cut in the sheer rail and lower profiled strip on the hull to accommodate the head rail/cathead knee. It's quite a complex curve and I was going to do it in two pieces to have a better chance of success but this seems to have come out ok. A profile will be cut into the front once the other piece is shaped up.
  19. Timmo
    No response to email orders and phone calls to westbourne and after some online research there's a disturbing number in the same boat. Can't even get hold of them to confirm the presumably undispatched order is cancelled.
  20. Timmo
    Nice work. Great start to a mouth-watering kit.
  21. Timmo
    Glad you got that brass sorted Julian. Those sheer rails are looking good. Nice work with the Lego for the ladder jig. I'll have to steal that idea.
  22. Timmo
    That would be a salute to the modeller from the gun crew, Doris.
  23. Timmo
    Nice work Jan. A top quality build.
  24. Timmo
    Thanks Jack, Dominic, there were a couple of victory/amiti Granadoes on the old MSW and I'm sure many would be interested to see the differences. How about a build log?
  25. Timmo
    Top work Ray. I think I'll be making some similar blocks with hooks now.

About us

Modelshipworld - Advancing Ship Modeling through Research

SSL Secured

Your security is important for us so this Website is SSL-Secured

NRG Mailing Address

Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917

Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)

Helpful Links

About the NRG

If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.

The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.

The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.

Our Emblem ®

Modelshipworld - Advancing Ship Modeling through Research

Nautical Research Guild ® and the NRG logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,999,236 & No. 6,999,237, registered March 14, 2023)

×
×
  • Create New...