-
Posts
5,535 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Everything posted by BANYAN
-
I love this model Steven, especially in her quasi-diorama - a very nicely displayed model. Hopefully you won't accidently catch one of those protruding corners in her new home? cheers Pat
-
Those gripes/sea lashings look so good Eberhard, very nicely done. Now I have something to try and emulate for the Victoria's boats Can I be so bold as to ask for a link to that material for making them? cheers Pat
-
How to "unstick" this chuck from the mill spindle?
BANYAN replied to rlb's topic in Modeling tools and Workshop Equipment
Hi Ron, I have a Sherline mill also. That chuck usually comes with a draw bar (threaded on one end and a bolt type head) that you put in from the top of the spindle assembly. I partially engage the thread of the draw bar into the chuck bore, give it a tap or two with a small rubber mallet (small hammer will work also) which usually disengages the tapered (morse) chuck head. If you don't have the draw bar, putting a metal rod of suitable OD down into the spindle bore and tapping that should also work, BUT put a rag or something under the chuck so that if it dislodges completely, it will fall onto a padded surface and not damage the cross-table or the chuck etc. The rod could be one of the many different bars/rods provided by Sherline, but should be a smaller OD than the bore, but bigger than the internally threaded bore in the top of the chuck (so that you don't drive the bar into this and damage the thread). I hope that resolves the issue for you. cheers Pat -
Hi Clovehitch. I had to do these for my build at 1:72 recently. I found I had to use very dense grained wood for any success. My method was to first file flats on either side of the boom inner end. To make the jaws I printed scaled copies of each jaw set as templates l(that is, the jaws as a full integrated piece). I thicknessed the wood to the appropriate thickness, and pasted the paper template onto it; and double sided taped (low tack) a sacrificial thin piece of wood under it to keep a clean cut. I then cut these to the required shape following the outer lines. Once cut, I sliced these in half to get the individual jaw pieces and sanded the centre cut back to the required line (to allow for boom neck thickness and taper. I removed the template but before separating the sacrificial piece away, I drilled holes at the required places to simulate the through bolts (leaving the sacrificial wood in place helps with protecting these thin pieces. I then removed the sacrificial piece and edge glued (two part epoxy for strength) to the flats on the neck being sure to keep them aligned. The following shows my test boom to prove the method and the final results. I hope this helps? The outer reefing combs look slightly large, but at this scale they are quite small and look better scaled to the naked eye. cheers Pat Pat
-
Your build is coming along very nicely Harry; looking good. WRT deck furniture, basically followed the dimensions given by Marquardt in his drawing (at scale) in his "Capt. Cook's Endeavour" Revised Edition. The exceptions being that I waited until I had placed the steering wheel and other deck equipment before making the skylight to fit. cheers Pat
-
The detailing is looking superb Greg, nice work. All that extra detail really takes your model up to another level. cheers Pat
- 212 replies
-
Doing a lot better than I ever could Steven; coming on very nicely. cheers Pat
- 409 replies
-
Looking good Keith; a few pointers (about the 'inside work' as you call it) that I can take away also - thanks. cheers Pat
-
Hi Richard. This is really nice work. I have been following along in the background (Stalking ), so I thought I had better post. This a very well constructed model and a very interesting subject for a model. cheers Pat
-
I like it Glen. Wouldn't the slight opaque finish simulate running (not agitated) water in the stream and mist anyway? cheers Pat
- 174 replies
-
- Waa Kaulua
- bottle
-
(and 1 more)
Tagged with:
-
Great progress Steven, a real little gem emerging. cheers Pat
- 409 replies
-
Well the dogs at least seem to be enjoying the surf. have a great break mate. cheers Pat
- 212 replies
-
Hi Ian, overall your build is looking great. One small point that may/may not bear further consideration is the motion/force of the bow wave on the verdigris seen on the ram. Would the leading edges of the ram be more 'clean'? I would not say polished as these would never have achieved sufficient speed to polish the edges. However would a gradient leading back from the leading edges be more realistic. That said, if the vessel had been alongside for a while this gradient would be gone but more salt/barnacles seen. Only offering this as you asked and may be a little OTT. cheers Pat
- 502 replies
-
- Quadrireme
- radio
-
(and 1 more)
Tagged with:
-
Those boats look great Jerry. cheers Pat
- 524 replies
-
- sloop of war
- constellation
-
(and 3 more)
Tagged with:
-
Great to see the use of modern technologies in improving our hobby Ian. Looking very good. cheers Pat
- 502 replies
-
- Quadrireme
- radio
-
(and 1 more)
Tagged with:
-
Very nice work Steven, that very much looks like salt water bleached wood. cheers Pat
- 409 replies
-
She's looking good Keith; and looking forward to seeing the corrections/improvements. cheers Pat
-
Hi Keith. It maybe one of those 'colour shifting' paints, depending on the ambient light and viewing aspect? I know there are several model paint suppliers such as SMS, now providing these. You sometimes have to put down a series of coats to get the right effect. A chap that goes by an avatar of "Barbados Rex' on you tube has rune some extensive tests of these paints for several suppliers. May be worth investigating? cheers Pat
About us
Modelshipworld - Advancing Ship Modeling through Research
SSL Secured
Your security is important for us so this Website is SSL-Secured
NRG Mailing Address
Nautical Research Guild
237 South Lincoln Street
Westmont IL, 60559-1917
Model Ship World ® and the MSW logo are Registered Trademarks, and belong to the Nautical Research Guild (United States Patent and Trademark Office: No. 6,929,264 & No. 6,929,274, registered Dec. 20, 2022)
Helpful Links
About the NRG
If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.
The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships.
The Nautical Research Guild has published our world-renowned quarterly magazine, The Nautical Research Journal, since 1955. The pages of the Journal are full of articles by accomplished ship modelers who show you how they create those exquisite details on their models, and by maritime historians who show you the correct details to build. The Journal is available in both print and digital editions. Go to the NRG web site (www.thenrg.org) to download a complimentary digital copy of the Journal. The NRG also publishes plan sets, books and compilations of back issues of the Journal and the former Ships in Scale and Model Ship Builder magazines.