glbarlow

Isopropyl alcohol will loosen the glue so you can reset the bulkhead. You want to do everything you can to have a squared up frame.

There are a full range of prices on Amazon. Frankly I'm not sure what justifies a high priced one. They are a basic tool, the ones I've had for years are still fine. They just have to tightly hold a bit. It is worth it to get multiple sized ones to accommodate multiple sized bits - I have four sizes, they're all I need. The larger ones, no matter how small a bit they hold, get in the way of small tight areas. I have these, or a version of them Amazon Pin Vise Set they have yet to fail me. I've never had nor understand the need to put a hand drilling device into a mechanical one. It's worth noting I've never seen an expensive tool I didn't like and in quite often buy (like Veritas mini-chisels for example), but in this case...

Just be sure the bulkheads are squared up completely before, during and after the glue is added. Fair them so you have a smooth run of a plank bow to stern. One way to make sure you don't over-do or under-do that task is to remove all the char others than a line of it on the the stern-facing edge forward of midships and the bow-facing for the bulkheads aft of midships. Take your time with fairing and take your time with your first planking. Study the other logs for a technique and don't be mislead by well-intentioned advice. There are many ways to plank, but mixing them is the worst way to go - choose one and stay with it. I've seen a lot of entry level modelers think there in a race to get past these first steps, but just like the concrete in a house the foundation is critical to future success, rush it and everything after is a mind-numbing challenge to correct. Planking is a skill, its fun when you do it right, it's misery when you try and force the planks to fit. It is not natural for a flat rectangle to fit opposing curves. Plank bending is an easily learned skill. My advice is to find and read Chuck Pasarro's tutorials, you can look at my LN, Cheerful, and now Winchelsea logs to see how I apply his techniques.. On the plans for LN, as you will see noted in other logs, two of the bulkheads are labeled incorrectly. It's fairly obvious they don't fit that way. The biggest flaw, though it will be a long while before you get there, is the forward bits are out of scale and incorrectly sized so badly the bowsprit won't fit. Some have just cut them down, I chose to scratch build a new set. You'll see this in other LN logs including mine. It's great you started a log - between that and using others that have gone before you can get plenty of advice to make up for the lack of quality instructions with the kit. Be sure to use the plans, even though they aren't crucial for this build, learning to follow along with the plans and use them when possible is excellent instruction and learning for more complicated models as you grow with the hobby. Welcome to modeling, we're glad you've joined us. I'll follow along with your build

Very creative cleat installer tools, that’s a very tight area.

I understand I’m about one millionth done with planking

Building this model as we know requires patience and perseverance. Rigging all the cannon doubles that requirement, well done. Not to set you back, but it’s not 22 more it’s 30 including the eight on the QD 😊

That’s a nice job on some tricky planks. Doing them will make a big difference on the final deck. When I made these for Cheerful I made sure the joints were between ports so a cannon didn’t cover them up.

I covered this in my LN log

any progress?

Thank you, I’m glad you found it. Cheerful was a joy to build.

So much nice detail work. Very well done!

The second layer and paint makes it look so much more like a ship. Fun stuff😊 Your planking looks great.

Cool, I like the entry way sign to the “factory.”

Thank you Frank! Thank you Dusan. You, Frank, and I are all about the same place. We’ll continue on together.

Thank you, but it’s far from that. I feel every mistake

Speaking of literal. This is a feel thing and it isn’t hard, just practice it some. I use a travel iron for bending (right on the wood of course) and just recently added a small crafters hot air device, not a hot air gun, for twisting. I use NO water, sometimes I may wet my finger and rub it over the wood. Just heat the wood, slowly bend it, hold it with clamps. I don’t bother letting it cool completely, it may spring back some or not. I can bend a blank in about a minute start to finish, a plank with two bends and a twist may take 3-4 minutes. If I don’t bend enough or bend it too much I just do it again. How long depends on the wood and the amount of bend. Again it’s a feel thing, it comes with practice. Read too many options here and there’s a danger of becoming paralyzed. I show my (actually Chuck’s) method in my current and previous two build logs.

Wales and upper planking complete The wales are now painted and finished. Before I move on to planking the rest of the hull I thought I’d pause and capture a few current state photos. Just on a simple blue background and with my iPhone, I’ll bring out the camera gear and white backdrop when I finish the hull. I chose to stay with my favorite Admiralty Ironworks Black. While purposed for simulating metal, I like the deep black matte finish it provides on wood. I started and finished with a coat of WOP. I like the smooth semi-polished finish the AYC wood allowed me to achieve. I sanded between coats with 400, then 800, and finally with 1200 grit sandpaper. Admiralty Paints come ready to use, but I thinned that a little more with distilled water. I feathered the wales and the black strake into the stem. It's nice to remember the top two rows will be covered by paper friezes later in the build, it made the surgery I did earlier easier to complete not worrying about color match. The black strake started at 1/32, I ran it through the thickness sander to about .63mm. Which I learned is about as thin as the sander can go. It stands proud of the planking and the wales stand proud of the strake, not by much but enough to look good, or so I think. Just to show my ship does have two sides. From the bow dead on. What is that dude looking at. The quarter shots - which does such a nice job showing the graceful lines. One from slightly above. A couple from full profile. And finally, the position my Winchelsea will be in for about the next 6 months. I’m taking a brief pause to take care of some neglected home chores, like tax prep. My photos won’t be very exciting for a while but I’ll post some progress photos from time to time just so you know I’m still here. Thank you for your support, comments, and likes. They are always appreciated.

I hope those hooks work out. I’m all for making our own hooks but the ones needed for cannon rigging would just look out of scale for anything we could practically make. I will vicariously enjoy the rigging watching yours develop 😊.

Really amazing work, such patience, diligence, and technical skill! Actual working door latches, wow.

Well done!

Thank you. The so far part is my ongoing challenge, I have a lot of planking in front of me😊

Thank you. Those are two words I’m always striving to achieve, planking is a great opportunity to practice both.

There are a lot of great Winnie builds, I’m doing my small part to encourage more. 😊

Thanks Rusty. Planking is still the thing that scares me most, I really don’t want to hold it up to the light and find I see through it 😳 so far so good.

I enjoy seeing what I hope mine will look like some far distant day, we’ll done Bob.