gjdale

.....two years later, I finally got around to making my own router table for the mill. I have basically copied Frank's (Mahuna) and Jay's (Modeler12). I used a piece of Melamine covered shelf for the base as it will give a nice slick surface to push stock over. The fence is 3mm aluminium angle. There are Sherline cap-screws through both the fence and on the main board that go into the mill table T-slots. For the "finger board" I used a piece of Delrin - the two screws go into T-nuts as per Frank's design. I didn't get around to adding the ball bearing "hold downs" as Jay has done, but I may get that soon. It works like a charm. Thanks Frank for your original post on this - sorry it took so long to get around to copying it!

Looking forward to watching another masterpiece evolve B.E.

Woohoo! FIrst in line for a front row seat!

Nice to see this one back on the table Wayne - looks good from here!

Thanks Mobbsie - good to see you back my friend. Thanks also to all the likes - it seems there is a bit of interest in this unusual kit. Continuing with the Fuselage..... The Neck Ring needs to be fitted to the Fuselage at a specific angle. To achieve this, the kit provides a template and instructs you to glue this to a piece of stiff card and then position the fuselage over the wing plan. Once in place, you are advised to: “prop the part at the correct angle with books etc so that it is unable to move”, then glue and clamp in place to allow the glue to dry. Hmmmm…….. I decided to try a slightly more robust approach, using a solid former. I used the kit provided template to define the angle that I cut on a piece of scrap timber, which just happened to be almost the perfect size to fit across the width of the fuselage. I had already had my wing plan laminated, so I stuck my former to the wing plan with double sided tape, and then stuck the Fuselage to the wing plan, also with double sided tape. That sucker is going nowhere in a hurry! That made attaching the Neck Ring very simple, and the next pic shows the whole set-up glued and clamped. The next components to fit to the Neck Ring are the pulleys and cable guides. The pulleys were fairly straight forward, being attached in the same way as the earlier ones on the underside of the fuselage. The cable guides are formed by gluing a bead on the shank of a cotter pin, then bending the cotter pin to the angle provided in the scale drawing in the instructions. So far, so good. Then you are invited to glue the newly constructed cable guide to the aft edge of the Neck Ring, such that the eye of the cable guide is aligned with the groove in the pulley. Once in place, the legs of the cable guide are wrapped in thread. To achieve this, I had to resort to using CA glue (which I generally avoid as I have become sensitized to it). The CA glue was just a temporary hold until I could get the thread “seizing” in place. I used some diluted PVA glue under the thread to help keep it in place as I was wrapping it, and then once the “seizing” was complete, I gave the whole thing another coat of diluted PVA. Here is relative close-up of the pulley and cable guide on one side. And here is an overview of the completed Neck Ring: And finally, here is an overview of the fuselage as it now stands. In this shot you can see where the Neck Ring has been trimmed flush with the fuselage and three nails (left over from a previous ship kit) inserted to “finish” the join. Leather straps are next on the agenda!

Congratulations on yet another fine piece of work B.E.

Great work Danny, and as always, instructional too. Looking forward to following your Bismarck build.

Chris, I think the material you are referring to might be Ezy-line - Greg Lester uses it on his magnificent builds. I believe it comes from the model rail road community.

I'm taking a seat in the front row too, Nils - always instructional to follow your builds.

Thanks Rusty and Mike. Rusty - I'm looking forward to sea trials too - won't be long now as the weather is starting to warm up down here. Mike - overalll, I think the kit is quite good. The use of Sintra (plastic) for the sub-planking is a little unusual for this type of build, and there are both pros and cons for it. You could make this model straight out of the box and have a reallly nice looking boat at the end. Or you can bash to your heart's content. Me? I couldn't help myself. I blame the CDO (that's like OCD, only with the letters in the right alphabetical order!!!!)

Great to see you bring this one home Mobbsie. She looks terrific and is a credit to your workmanship - be proud my friend. I look forward to the commencement of Pickle.

Thanks Steven, Nils, Sam, Ken, Richard and Carl for your interest, and also to the "likes" for looking in. Fuselage Construction Construction begins with the Fuselage. Here is a picture from the Instruction Manual of the overall completed assembly: My first task was to cut a new piece for the fuselage base, replacing the kit-provided wood with Cherry of the same thickness (3/16”). Prior to cutting to shape, I laid out all the markings per the instructions and drilled the holes (4 x 2mm and 6 x 1mm diameter). I finished the surface with two coats of shellac and a coat of furniture wax. This is something I’ve picked up recently from doing some 1:1 scale woodwork. The advantage of shellac is that it dries very quickly, is dead easy to apply, and provides a repairable finish. It also highlights the natural beauty of the timber. Here are the prepared base and the kit provided part side by side. Next up was making some cleats. The kit provides some stock wood cut roughly to shape and then instructs you to finish the shaping with files and stain them walnut. I replaced these with straight walnut, which again got the shellac/wax treatment after final shaping. Here’s a shot showing the raw kit parts and my finished parts: The next step was to fit one cleat, four cable guides, two pulleys and the crankshaft. The cable guides are simply cotter pins, cut off so as not to protrude through the base to the other side. The pulleys are small brass parts that are secured with a small brass nail, again cut to length. The crankshaft is made from a piece of piano wire that is first bent to shape following a template in the instruction book. Four beads are glued in place on the crankshaft as seen in the pictures below. A small recess was filed into the fuselage base to allow the beads to seat and the crankshaft to sit flush against the fuselage. The two clamps holding the crankshaft in place were again replacement parts made from cherry, using the kit parts as templates for sizing. Here’s another view using a different background: Forming the Neck Ring is the next step. The kit provides some cherry veneer to this, which it then tells you to stain walnut. I used walnut instead. Two pieces of 1/64” thick by ¼” wide walnut strip are laminated by bending around a former cut from a scrap piece of 1/2" plywood, using a template provided in the kit. I wet these and then hit them with a heat gun to set some initial curve in them. Then I applied some PVA and re-clamped to the former and left them to set. Next up is the Fulcrum Mount. Again, simply made from Cherry using the kit part as a template. The bottom edge is filed to a curve to match the Neck Ring. A large cotter pin is then then inserted in the centre of the top edge, and finally the cotter pin is wrapped in thread. That’s as far I have progressed to date.

Nice to see an update Gil - she sure is looking sweet.

Nice to see you back at it Rusty.

Just superb Nils, and what a collection!

I'm in too Ken - always interested to follow your thoughtful solutions to the inevitable challenges ahead.

Thanks Popeye, I'm looking forward to the weather warming up so that we can go for "sea trials".

Thank you very much Lawrence - you are very kind to say so.

Thank you very much Nils and Elia.

Thanks very much Gary, Dave and Zappto.

This kit was a Christmas present from my wife in 2013. It has sat in the “stash” since then, calling to me occasionally. I originally came across this on the previous MSW site. We had recently returned from a European holiday where Da Vinci’s art had featured quite strongly, so naturally I was drawn to this kit. The kit is produced by The Imagination Factory, but a recent check of their website (www.davincistore.com) site suggests that the kit is either temporarily or permanently unavailable. The kit was designed by artist Robert Coyle, based on his extensive research of Da Vinci’s drawings. What’s in the box? The kit box is quite large, but there is a lot a free space inside. It seems that the box length was determined by the lithograph wing plan, which is both required for building, and a lovely piece of art in its own right. So the main box contained the lithograph, some tulle-type of fabric (for the wings), a couple of longer dowels (also part of the wings), the display base (in two parts), the instruction manual and a much smaller box containing the majority of the kit parts. Opening the smaller box, we find most of the parts ‘carded’ with a small drawing to help identify part numbers. I immediately re-packaged all of the small parts into labelled zip-lock bags. The wood appears to be mainly bass wood, and although it appears to be reasonable quality, I had made up my mind that I would replace all of the kit-provided wood with a mixture of Boxwood, Cherry, and Walnut, all of which I ordered from Jeff Hayes at Hobbymill before he closed the business. The plan is to use the pre-cut parts as templates to make my own from the new wood. The instruction manual is interesting in that all of the drawings look like they are hand-drawn. It really adds a very nice artistic flair to the entire kit. Here’s a couple of pictures from the manual: That’s about as far as I got today. Building will commence in earnest shortly, so stay tuned….

Looking good Slog - your care and effort is really paying off.

Nice to see back in the shipyard Hamilton. Glad to hear the surgery was a success and hope the recovery continues to go well for you. Don't get lazy with the exercises either - they will make a huge difference in the long run!

Sorry to hear you've been under the weather Danny - there's been some really nasty flu bugs going around this year. Glad to hear you're on the mend though. And the build is looking outstanding!

Lovely work as always Bob.